Steren SN74LS47N Manual


Læs gratis den danske manual til Steren SN74LS47N (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Steren SN74LS47N, eller vil du spørge andre brugere om produktet?

Side 1/8
Semiconductor Components Industries, LLC, 1999
December, 1999 – Rev. 6
1Publication Order Number:
SN74LS47/D
The SN74LS47 are Low Power Schottky BCD to 7-Segment
Decoder/Drivers consisting of NAND gates, input buers and seven
AND-OR-INVERT gates. They offer active LOW, high sink current
outputs for driving indicators directly. Seven NAND gates and one
driver are connected in pairs to make BCD data and its complement
available to the seven decoding AND-OR-INVERT gates. The
remaining NAND gate and three input buers provide lamp test,
blanking input/ripple-blanking output and ripple-blanking input.
The circuits accept 4-bit binary-coded-decimal (BCD) and,
depending on the state of the auxiliary inputs, decodes this data to
drive a 7-segment display indicator. The relative positive-logic output
levels, as well as conditions required at the auxiliary inputs, are shown
in the truth tables. Output congurations of the SN74LS47 are
designed to withstand the relatively high voltages required for
7-segment indicators.
These outputs will withstand 15 V with a maximum reverse current
of 250 µA. Indicator segments requiring up to 24 mA of current may
be driven directly from the SN74LS47 high performance output
transistors. Display patterns for BCD input counts above nine are
unique symbols to authenticate input conditions.
The SN74LS47 incorporates automatic leading and/or trailing-edge
zero-blanking control (RBI and RBO). Lamp test (LT) may be
performed at any time which the BI/RBO node is a HIGH level. This
device also contains an overriding blanking input (BI) which can be
used to control the lamp intensity by varying the frequency and duty
cycle of the BI input signal or to inhibit the outputs.
Lamp Intensity Modulation Capability (BI/RBO)
Open Collector Outputs
Lamp Test Provision
Leading/Trailing Zero Suppression
Input Clamp Diodes Limit High-Speed Termination Effects
GUARANTEED OPERATING RANGES
Symbol Parameter Min Max UnitTyp
VCC Supply Voltage 4.75 5.0 5.25 V
TAOperating Ambient
Temperature Range
0 25 70 C°
I
OH Output Current – High
BI/RBO
– 50 A
IOL Output Current – Low
BI/RBO
BI/RBO
3.2 mA
VO(off) O–State Output Voltage
a to g
15 V
IO(on) On–State Output Current
a to g
24 mA
LOW
POWER
SCHOTTKY
SOIC
D SUFFIX
CASE 751B
http://onsemi.com
PLASTIC
N SUFFIX
CASE 648
16
1
16
1
Device Package Shipping
ORDERING INFORMATION
SN74LS47N 16 Pin DIP 2000 Units/Box
SN74LS47D 16 Pin 2500/Tape & Reel
SN74LS47
http://onsemi.com
2
LOGIC SYMBOL
CONNECTION DIAGRAM DIP (TOP VIEW)
BCD Inputs
Ripple–Blanking Input
Lamp–Test Input
Blanking Input or
Ripple–Blanking Output
Outputs
A, B, C, D
RBI
LT
BI/RBO
a, to g
0.5 U.L.
0.5 U.L.
0.5 U.L.
0.5 U.L.
1.2 U.L.
Open–Collector
0.25 U.L.
0.25 U.L.
0.25 U.L.
0.75 U.L.
2.0 U.L.
15 U.L.
NOTES:
a) 1 Unit Load (U.L.) = 40 A HIGH, 1.6 mA LOW.
b) Output current measured at VOUT = 0.5 V
b) The Output LOW drive factor is 15 U.L. for Commercial (74) Temperature Ranges.
HIGH LOW
(Note a)LOADING
PIN NAMES
14 13 12 11 10 9
1 2 3 4 5 6
VCC
7
16 15
8
f g a b c d e
B C LT BI / RBO RBI D A GND
VCC = PIN 16
GND = PIN 8
7 1 2 6 3 5
13 12 11 10 9 15 14 4
A B C D LT RBI
a b c d e f g
BI/
RBO


Produkt Specifikationer

Mærke: Steren
Kategori: Ikke kategoriseret
Model: SN74LS47N

Har du brug for hjælp?

Hvis du har brug for hjælp til Steren SN74LS47N stil et spørgsmål nedenfor, og andre brugere vil svare dig