Supermicro SuperServer 2028TP-HC1TR Manual

Supermicro Server SuperServer 2028TP-HC1TR

Læs gratis den danske manual til Supermicro SuperServer 2028TP-HC1TR (1 sider) i kategorien Server. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Supermicro SuperServer 2028TP-HC1TR, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

http://www.supermicro.com MNL-1659-QRG

Board Layout

SuperServer 2028TP-HC1R/HC1TR/HC1FR Quick Reference Guide

Rear View

BIOS Beep Codes

Beep Code/LED Message Description

1 beep Refresh Circuits have been reset.

(Ready to power up)

5 short beeps + 1 long

beep

Memory Error

5 beeps and 2 short

beeps

Display memory

read/write error

CPU Installation

Beep Codes

Front view & Interface



Heatsink Installation

1. Place the heatsink on top of the installed CPU.

2. Align the four screws to the socket.

3. Holding the heatsink in place, screw down as shown

(cross pattern, in order: A, C, B, D).

4. Note: Only use 6-8 lb/f of torque; otherwise, hand-tighten

each screw to avoid damaging the CPU.

MEMORY

Caution

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning

before connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING

To reduce risk of electric shock/damage to equipment,

disconnect power from server by disconnecting all power

cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap

CAUTION

Always be sure all power supplies for this system have

the same power output. If mixed power supplies are

installed, the system will not operate.

Align CPU to socket;

install CPU straight down

For more information go to :

http://www.supermicro.com/support



No memory detected

NOTE:

Do not bend pin inside socket



Processors and Memory Module Population for Optimal Performance

Number of

CPUs + DIMMs

CPU and Memory Population Configuration Table

(For memory to work properly, follow the instructions below)

1 CPU & 2 DIMMs CPU1: P1-DIMMA1/P1-DIMMB1

1 CPU & 4 DIMMs

1 CPU & 5~8 DIMMs

2 CPUs & 4 DIMMs

2 CPUs & 6 DIMMs

CPU1: P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1

CPU1: P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1 +

Any memory pairs in P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2 slot

CPU1 + CPU2: P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1

CPU1 + CPU2: P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1

2 CPUs & 8 DIMMs

2 CPUs &

10~16 DIMMs

2 CPUs & 16 DIMMs

CPU1 + CPU2: P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1

+ Any memory pairs in P1, P2 DIMM slots

CPU1 + CPU2: P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1,

P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-DIMME2/P2-DIMMF2/P2-DIMMG2/P2-DIMMH2

Processors and their Corresponding Memory Modules

CPU# Corresponding DIMM Modules

CPU 1 P1-DIMMA1

CPU 2 P2-DIMME1

P1-DIMMB1

P2-DIMMF1

P1-DIMMC1

P2-DIMMG1

P1-DIMMD1

P2-DIMMH1

P1-DIMMA2

P2-DIMME2

P1-DIMMB2

P2-DIMMF2

P1-DIMMC2

P2-DIMMG2

P1-DIMMD2

P2-DIMMH2

Motherboard Drawer Locations in the Chassis

Motherboard B

Controls HDDs B1 to B6

Motherboard D

Controls HDDs D1 to D6

Motherboard A

Controls HDDs A1 to A6

Motherboard C

Controls HDDs C1 to C6

Nodes and Corresponding Hard Drives

Hard Drive Signal

Hard Drive Fail

Power Button

LAN LED

Alert

UID Button

Description

No.

DescriptionNo.

SXB1: S-SATA 0-2/PCI-E 3.0 p1-x16 Slot supported by CPU2

P2-DIMME1/P2-DIMME2 slot

P2-DIMMF1/P2-DIMMF2 slot

Slot1: CPU2 Slot1 PCI-E 3.0 x16

JBT1: CMOS Clear

Slot2: CPU2 Slot2 PCI-E 3.0 x8

CPU2

InfiniBand (FDR) Connector (2028TP-HC1FR only)

Gigabit LAN1/LAN2 or 10G Base-T Connector (2028TP-HC1TR only)

S-SATA3: SATA DOM (Disk_On_Module) with Power-pin Connector

JSD1: SATA DOM (Device_on_Module) Power Connector

P2-DIMMH1/P2-DIMMH2 slot

P2-DIMMG1/P2-DIMMG2 slot

P1-DIMMA1/P1-DIMMA2 slot

P1-DIMMB1/P1-DIMMB2 slot

CPU1 (Install CPU1 first)

P1-DIMMD1/P1-DIMMD2 slot

P1-DIMMC1/P1-DIMMC2 slot

SXB2: I-SATA 0-5/PCI-E 3.0 p1-x8 Slot supported by CPU1

Low-Profile PCI-E Slot

IPMI LAN Port

Power Supply Module

UID Button

VGA Connector

InfiniBand Port (2028TP-HC1FR only)

G_LAN or 10G Base-T Connector

USB Ports

Video adapter missing or with faulty

memory

SNK-P0057PS for CPU2

SNK-P0047PSM for CPU1

(Close to fan)

Screw #B

Screw #D

Screw #C

Screw #A

58 6

MB:D

MB:B

MB:C

MB:A

Node A

Node B

Node C

Node D

2 1

1 continuous beep System Overheat System Overheat

JBT1

P1-DIMMB2

S-SA TA3

COM1

JIPMB1

FAN3

FAN4

JSD1

JTPM1

JF1

UID_LED1

BMC_HB_LED1

JPG1

JPB1

JVRM2

JVRM1

JWD1

JPL1

/CPU2 PCI-E 3.0 X16)

(CPU2 SLOT1 PCI-E 3.0 X16)

PCI-E 3.0 X8)(CPU2 SLOT2

UID SW

BATTERY

BIOS

BMC

QSFP

LAN1/LAN2

10G/1G

(3.0)

USB0/1

IPMI_LAN

SATA DOM+POWER

TPM/PORT80

CPU2 VRM_HS1

CPLD

P2-DIMMG1

P2-DIMMH2

P2-DIMMH1

P2-DIMMG2

P2-DIMMF2

P2-DIMME1

P2-DIMME 2

P2-DIMMF1

P1-DIMMD2

P1-DIMMD1

P1-DIMMC2

P1-DIMMC1

P1-DIMMB1

P1-DIMMA2

P1-DIMMA1

/CPU1PCI-E 3.0 X8)(I-SATA0~5

CPU2

CPU1

LAN CTRL

PCH

IB_LINK LED1

IB_ACT_LED1

(S-SATA0~2

SXB1 SXB2

Slot1 Slot2

X10DRT-P Series

Rev. 1.02

1516

1819

VGA

SXB1

SXB2

5 6 7 8 119 10

ID tag

Note:

1. Install CPU1 first.

2. In order to support PCI-e slots, two CPUs must be installed.

Populating RDIMM/LRDIMM DDR4 Memory Modules

Type

Ranks

Per DIMM

and Data

Width

DIMM Capacity

(GB)

Speed (MT/s); Voltage (V); Slots per Channel (SPC) and

DIMMs per Channel (DPC)

2 Slots per Channel

1 DPC 2 DPC

E5-2600 V3 E5-2600 V4 E5-2600 V3 E5-2600 V4

4 Gb 8 Gb 1.2 V 1.2 V 1.2 V 1.2 V

RDIMM SRx4 8 GB 16 GB 2133 2400 1866 2133

RDIMM SRx8 4 GB 8 GB 2133 2400 1866 2133

RDIMM DRx8 8 GB 16 GB 2133 2400 1866 2133

RDIMM DRx4 16 GB 32 GB 2133 2400 1866 2133

LRDIMM QRx4 32 GB 64 GB 2133 2400 2133 2400

LRDIMM 3DS 8Rx4 64 GB 128 GB 2133 2400 2133 2400

Rev 1.0a

ÌMNL-1659-QRG-10anÎ

Screw #B

Screw #D

Screw #A

Screw #C

Produkt Specifikationer

Mærke:	Supermicro
Kategori:	Server
Model:	SuperServer 2028TP-HC1TR

Har du brug for hjælp?

Hvis du har brug for hjælp til Supermicro SuperServer 2028TP-HC1TR stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Server Supermicro Manualer

Supermicro SuperServer SYS-221BT-HNC8R Manual

23 Juli 2025

Supermicro SuperServer 1019S-MC0T Manual

6 Juli 2025

Supermicro SuperServer 2028U-TR4T+ Manual

25 Juni 2025

Supermicro SuperServer SYS-2029U-E1CRT Manual

19 Juni 2025

Supermicro SuperServer 6028TR-HTR Manual

30 Januar 2025

Supermicro SuperServer 6019U-TR4 Manual

30 Januar 2025

Supermicro SBA-4119S-T2N Manual

11 Januar 2025

Supermicro A+ Server 1024US-TNR Manual

11 Januar 2025

Supermicro SuperServer 2028U-TNRT+ Manual

11 Januar 2025

Supermicro SuperServer 2028TR-HTFR Manual

8 Januar 2025

Server Manualer

Nyeste Server Manualer

Asus TS300-E6/PS4 Manual

14 August 2025

Asus TS500-E6/PS4 Manual

14 August 2025

Asus RS161-E5/PA2 Manual

13 August 2025

Asus P5BV-C Manual

13 August 2025

Asus RS540-E8-RS36-ECP Manual

13 August 2025

Asus RS300-E6/PS2 Manual

12 August 2025

Asus RS120-E5/PA4 Manual

12 August 2025

Asus P5BP-E/4L Manual

11 August 2025

Dell PowerEdge M915 Manual

9 August 2025

Dell PowerEdge R360 Manual

9 August 2025