Supermicro SuperServer 5019P-MT Manual

Supermicro Server SuperServer 5019P-MT

Læs gratis den danske manual til Supermicro SuperServer 5019P-MT (14 sider) i kategorien Server. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Supermicro SuperServer 5019P-MT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/14

Information for Lot 9 of d )ErP (Eco esign

This addendum addresses E European Union (EU) codesign requirements for servers and storage

products addendum product. All and ratings within this data are in reference only Supermicro to the (s) in

the manual. The below information conforms ommission to requirements laid down Cin Annex II of the

R . egulation 2019/424

3(1)(a): e See Section 1.1 of th system manual for the product type.

3(1)(b): See the title page and preface of the system manual for the trademark and

manufacturer’s address.

3(1)(c): (s). See the title page of the system manual for product model number

3(1)(d): . See the serial number on the physical system to determine the year of manufacture

3(1)(e-j): PSU E actor V ) (F fficiency and Power F alue (Table rom 80 Plus report)

PSU Model #: PWS- -350

Watts: 350W

PSU Efficiency

Power orFact

% of Rated Load

% % % %10 20 50 100

50 %

Single -Output (AC DC)

86.10%

91.00%

92.51%

90.18%

0.99

E P System (EUT) fficiency in I Sdle tate ower (Table)

Representative

Configurations

Measured Idle State

Power (W)

Calculated Idle Power

Allowance (W)

High-End Performance

Configuration

106.6

2 72.0

Typical Configuration

N/A

Low-End Performance

Configuration

6 2.1

23 3.6

System E P(EUT) fficiency in A Sctive tate ower (Table)

Representative

Configurations

Active tate S

E Score fficiency

(Effserver)

Minimum A Sctive tate

Efficiency

High-End Performance

Configuration

21.9

Typical Configuration

N/A

Low-End Performance

Configuration

19.0

3(1)( is k): The operating condition class A2.

Dry bulb °Ctemp

Humidity range, non condensing-

Operating

condition

class

Allowable

range

Recom

mended

range

Allowable range

Recommended range

Max dew

point (°C)

Maximum

rate of

change

(°

C/hr)

15- 32

18 27-

–

12 and °C Dew P oint (DP)

8 % (RH) relative humidity to

17 80 ° C DP and % RH

–

9 °C DP to

15 °C DP and

60 % RH

5/20

10 35-

18 27-

–

12 and to °C DP 8 % RH

21 °C DP % RHand 80

Same A1as

5/20

5-40

18 27-

–

12 and to °C DP 8 % RH

24 °C DP % RHand 85

Same A1as

5/20

5-45

18 27-

–

12 and to °C DP 8 % RH

24 °C DP % RHand 90

Same A1as

5/20

3(1)(l): The idle state power at the higher boundary temperature of the operating conditions

class is 125.79W.

3(1)( ism): The active state efficiency and performance a minimum of 1 . 9.0

3(1)(n): There are two methods by which a user can securely delete data from this system. The

user performing secure data deletion should be an IT professional.

The first is with a Unified Extensible Firmware Interface (UEFI) shell utility. This utility

works on X10/X11/H11/H12/M11 motherboard series with onboard SATA/NVMe devices.

Any user may access and download this utility through following link:

https://www.supermicro.com/about/policies/disclaimer.cfm?url=/wftp/utility/Lot9_Secure

_Data_Deletion_Utility/

Download the shell utility package and extract it to a USB flash drive, then plug the drive

into the server for which secure data deletion is necessary. Then turn the system on.

Navigate to the BIOS setup menu, then place the server system into the UEFI shell

environment. Follow the instructions in the README file to invoke the utility and

complete the deletion.

The second method is through the secure data deletion tool provided by the original

manufacturer of the hard drive. This should be used in a scenario where the shell utility

is not applicable. Each manufacturer should have the tool available on their website. If

needed, please look on the hard drive label for the name of the manufacturer and model

information.

3(1)(o): List of recommended combinations of blade servers with chassis: N/A.

3(1)(p): . List of all current SKUs within this product family: N/A

3(3)(a): There is no use of cobalt in batteries in this product.

Produkt Specifikationer

Mærke:	Supermicro
Kategori:	Server
Model:	SuperServer 5019P-MT

Har du brug for hjælp?

Hvis du har brug for hjælp til Supermicro SuperServer 5019P-MT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Server Supermicro Manualer

Supermicro SuperServer 6028TR-HTR Manual

30 Januar 2025

Supermicro SuperServer 6019U-TR4 Manual

30 Januar 2025

Supermicro SBA-4119S-T2N Manual

11 Januar 2025

Supermicro A+ Server 1024US-TNR Manual

11 Januar 2025

Supermicro SuperServer 2028U-TNRT+ Manual

11 Januar 2025

Supermicro SuperServer 2028TR-HTFR Manual

8 Januar 2025

Supermicro SuperBlade SBI-4129P-C2N Manual

28 December 2024

Supermicro SuperServer F619P2-RC1 Manual

28 December 2024

Supermicro SuperServer E300-9A-4C Manual

28 December 2024

Supermicro SuperServer 5029AP-TN2 Manual

28 December 2024

Server Manualer

Nyeste Server Manualer

15 Juni 2025

7 Juni 2025

1 Juni 2025

9 Marts 2025

9 Marts 2025

9 Marts 2025

23 Januar 2025

23 Januar 2025

23 Januar 2025

23 Januar 2025