Switel DH-100 Manual

Switel Alarmsystem DH-100

Læs gratis den danske manual til Switel DH-100 (2 sider) i kategorien Alarmsystem. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Switel DH-100, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
MA-600 is a plug-in receiver, it can carry two wireless transmitters
such as doorbell buttons with two distinguishable flash pattern.
The first coded transmitter will flash rapidly; the second coded
transmitter flashes slower.
Step 1: Press & Hold the Learn button
fo r 3 se co nd s. Th e re d L E D
indicator inside the lens will blink.
(if the red LED indicator lights
Please see section 3)
Step 2: Press the Melody selector button ♫
to scroll through the melodies.
Once you hear a melody you
prefer, do not press any button as
t h e m e l o d y i s s e t f o r t h a t
transmitter.
Step 3: Once the melody is selected, trigger the transmitter to
pair. If successful, the receiver (chime unit) will
generate a short tone. Press the Learn selector
button to exit the pairing mode, the system is now
ready to use.
PARTS & FUNCTION
MOUNTING & POWER
Flasher
Indicator
Function
switch
Speaker
Melody
button
Learn
button
Wall plug
(AC plug)
Press & hold the Learn button for 3 seconds to enter the pairing
mode. Press the Learn button to scroll between 1 and 2
transmitters , press the Melody selector repeatedly until you ♫
have found the desired melody.
Trigger the transmitter to confirm the melody, when you hear a
twice short tone press the Learn button to exit.
1. ASSIGNMENT OF THE TRANSMITTER
3. CLEAR THE TRANSMITTER FROM THE RECEIVER
MEMORY
Press & hold the Learn button for 3 seconds to enter the
pairing mode. Press & hold both the Learn button & the ♫
Melody selector together for 3 seconds to delete the memory.
The re ceiv er wil l g ener ate a bee p tone to in dica te all
transmitters on the memory is deleted. The red LED will change
to blink. Now you can pair the new transmitters to the receiver
as per the previous section.
Melody
Learn
USER MANUAL
4. TRA NSMI TTER B ATTE RY LOW
When the indicator lights constantly after triggered, it indicates this
transmitter is battery low. Please replace its battery as soon as possible.
This receiver works with AC 80V to 240V. Simply plug into a well
visible AC wall socket, it'll turn on.
* PLEASE NOTE THE TRANSMITTER & RECEIVER ARE
READY TO USE
Two transmitters can be assigned to the receiver by sequence.
The transmitter can only be assigned if it is not yet known in the
memory of the receiver.
2. CHANGE THE MELODY
PAD TRANSMITTER
Part & Function
Battery installation
Mono jack for
External sensor
Battery
compartment
* Unlock the screw
* Slide to open the cover
* Insert a CR2032
Battery "+" face up
Switch for
Fall Mat or
Bed Pad +
Delay
If the coding is the same as another transmitter universal transmitter
you must change the code. When you have changed the code re-pair
the . universal transmitter
Open the cover
Remove the battery
Press and hold the test button, insert
the battery whilst holding the button
for 5 seconds. The LED will flash 5 times
when a new code is generated
+
+
+
+
+
Setting
+
Pad
Mat
+ 3S
+ 10Min
Temporary Cancel Call Button
To cancel the call button function, press and hold the call
button 5 secons. The LED will blink 4 time to indicate the call
button is disable.
To enable the call function, press and hold the call button 5
seconds again. The LED will blink 2 time to indicate the call
function is enable.
Call
Button
Open the battery cover and slide the switch
to pad or mat position
Mat: for fall mat (normal open)
Pad: for Bed pad or chair pad (normal
close)
+3S: Alert after the person leave the pad
more than 3 seconds
+10Min: Alert after the person leave the
pad more than 10 minutes seconds
OPERATION
Pad
Connection
Mat
1. open the battery cover
2. Connect the pressure pad to the
transmitter
3. close the battery cover
o 2.5 mono plug
/
The elder person normally lay on the mat, when the person leave the mat
more then 2 second, the transmitter will send out the alert signal to the
receiver
EXIT
The transmitter will send out the alert signal to the receiver, when some
step on (fall on) the mat The universal transmitter can connected to other
type of sensor such as a switch.
Code Conflict
Paring to the receiver
The Sensor is already paired with the receive. You can add (pair) one more
transmitter to the system follow the instructions of the receiver.
DH-100

Produkt Specifikationer

Mærke: Switel
Kategori: Alarmsystem
Model: DH-100

Har du brug for hjælp?

Hvis du har brug for hjælp til Switel DH-100 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Alarmsystem Switel Manualer

Switel

Switel DH-100 Manual

11 December 2024

Alarmsystem Manualer

Nyeste Alarmsystem Manualer

Abus

Abus Smartvest Pro FUMK45000 Manual

29 Oktober 2025
B.E.G.

B.E.G. PD11-KNXs-FLAT-ST Manual

8 Oktober 2025
Hikvision

Hikvision DS-PD201MC-WB Manual

30 September 2025
Evolveo

Evolveo Alarmex Pro Manual

18 September 2025
Kemo

Kemo M062 Manual

18 September 2025
Velleman

Velleman K8093 Manual

17 September 2025
Smartwares

Smartwares FGA-13091 Manual

16 September 2025
Brandson

Brandson 304339 Manual

15 September 2025
Kidde

Kidde SM120X Manual

14 September 2025
Elektrobock

Elektrobock ELBO-073 Manual

14 September 2025