Teledex BTX4750 Manual

Teledex Telefon BTX4750

Læs gratis den danske manual til Teledex BTX4750 (3 sider) i kategorien Telefon. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Teledex BTX4750, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

CONNECTING THE BTX4750

Included with the BTX4750 are (one each):

• Base unit • Coiled handset cord • User guide

• Handset • Clear plastic overlay • Line cord

Contact your supplier or Teledex for information on ordering

custom designed and printed faceplates to enhance the look of your

Teledex BTX4750 telephone.

1) Located on the left side of the BTX4750 is a modular jack

labeled TO HANDSET. Insert one end of the coiled handset cord

into this jack (until you hear it click).

2) Insert the other end of the coiled handset cord into the modular

jack on the handset.

3) Turn the telephone so the back panel is facing you. Insert either

end of the line cord into the jack on the back of the telephone

this jack is labeled TO TEL.

4) Insert the other end of the line cord into a telephone wall jack.

5) The overlay is easiest to remove by, with your fingers, squeezing

the outer edges causing a slight bow in the middle, then carefully

remove one side of the overlay from the 3 tab guides. The over-

lay is easiest to insert when; The left or right side tabs are insert-

ed first, and the middle part of the overlay is slightly bowed to

allow for insertion of the other tabs.

SELECTING LINE 1 AND LINE 2

Line 1 or Line 2 is selected by depressing one of the latching line

keys. The line key that is depressed is the active line when using the

handset. Pressing the alternate line key will make the other line

active. Use the key to place callers on hold while connectingHOLD

to the other line.

ADJUSTING THE RING VOLUME

The BTX4750 has two ring volume settings.

To change the ring volume:

Locate the adjustment control on the back of the telephone labeled

RINGER LOW/HI. There are two controls (labeled L1 for Line 1 and

L2 for Line2). Slide the switch to the desired LOW or HI ring vol-

ume for each line.

RECEIVING A CALL

1) Press button for Line 1 or Line 2 to activate the ringing line. A

red flashing LED indicates which line is ringing.

2) Lift the handset to connect to the ringing line.

3) To end the call, hang up by replacing the handset.

PLACING A CALL

1) Select Line 1 or Line 2 (if not previously selected).

2) Lift the handset. The line LED will turn green indicating line in use.

3) Listen for dial tone, dial the desired number, or press an autodial

key to automatically dial a number.

4) To end the call, hang up by replacing the handset.

VISUAL RING INDICATOR AND MESSAGE WAITING

LIGHT

The raised red lens is a Visual Ring Indicator and Message Waiting

light. The lens will flash when the telephone is ringing. Additionally,

some telephone systems permit an operator or message center to turn

on the red Message Waiting light to alert you that you have a message.

USING THE HOLD KEY

To place a call on Hold for Line 1 or Line 2:

Press the red key. The Line LED light will change to red andHOLD

Line key will un-latch. The handset can be replaced without discon-

necting the call.

USING THE DATA PORT

The DATA PORT is a modular jack, located on the right side of the

telephone, labeled DATA. The DATA PORT provides convenient

access to the telephone lines for connecting modems, fax and

answering machines or other telephone components (Line 1 can be

used for

voice calls and Line 2 can be used for data calls simultaneously).

To use the DATA PORT:

Insert the modular line cord from your facsimile machine, modem,

etc., into the jack labeled DATA. The DATA PORT will only access

Line 2. When using the telephone for voice communications and

data communications at the same time, use Line 1 for your voice

communications.

HANDSET VOLUME KEY

The HANDSET VOLUME key will increase the handset volume.

Pressing this button during a call will increase the receive volume,

pressing the key again will return the volume to the normal level.

The handset volume is reset to normal with each new call.

REDIAL

To REDIAL the last telephone number dialed:

1) Press Line 1 or Line 2 to select a line.

2) Lift the handset.

3) Press the REDIAL key. The BTX4750 will dial the last number

dialed.

AUTO DIAL KEYS

The BTX4750 has 11 programmable AUTO DIAL keys. These keys

can be programmed to automatically dial telephone numbers or acti-

vate telephone system features.

Some of the AUTO DIAL locations may have been preprogrammed

before installation.

STORING AUTO DIAL KEYS

The telephone must be connected to a telephone line.

1) Lift the handset.

2) Press the STORE key and release it.(see diagram for key location).

3) Enter the telephone number including PAUSE or FLASH* as

required The dialing sequence can be up to 15 digits.

4) Press the AUTO DIAL key where the number is to be stored.

5) Hang up the handset.

*A 3.6 second pause is entered in a dialing sequence by pressing the

REDIAL key for each PAUSE required.

FLASH KEY

Pressing the key initiates a 600ms hookflash. Typical usage isFLASH

to access PBX/CO features like transfer and conference call.

STORE KEY

This key is used when storing numbers in the AUTO DIAL keys.

MUTE KEY

Press the Mute key, the red LED below the key will light. TheMUTE

party on the other end will not hear you when the MUTE key is

depressed. Pressing the key again will release the key. This willMUTE

allow the other party to hear you. This is for both handset and

speakerphone calls.

PLACING A CALL ON THE SPEAKERPHONE

1) Without lifting the handset, press the SPEAKERPHONE key. The

red Speaker LED will light.

2) Listen for dial tone. Dial the desired number, or press an AUTO

DIAL key to automatically dial a number.

3) To end speakerphone calls, press the key . TheSPEAKERPHONE

LED will go out.

TIPS FOR USING THE SPEAKERPHONE

1) Face the telephone to talk (the microphone is located on the

front edge of the telephone).

2) To go to handset mode, lift the handset, the speakerphone will

automatically go off. To return to speaker mode, press the

SPEAKERPHONE key, the LED will light. Replace the handset

(hang up).

3) To end a speakerphone call, press the SPEAKERPHONE key.

ADJUSTING SPEAKERPHONE VOLUME

To increase/decrease speakerphone volume:

BTX4750

GUESTROOM TELEPHONE

USERS GUIDE

Produkt Specifikationer

Mærke:	Teledex
Kategori:	Telefon
Model:	BTX4750

Har du brug for hjælp?

Hvis du har brug for hjælp til Teledex BTX4750 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Telefon Teledex Manualer

Teledex A105 Manual

6 November 2025

Teledex SIP ND210L Manual

12 Januar 2025

Teledex A110 Manual

6 September 2024

Teledex SIP ND2105 Manual

18 August 2024

Teledex Pearl S Manual

18 August 2024

Teledex SIP LD4210S Manual

18 August 2024

Teledex SIP ND2105S Manual

18 August 2024

Teledex SIP ND2110 Manual

18 August 2024

Teledex SIP ND2110S Manual

18 August 2024

Teledex SIP LD4105S Manual

18 August 2024

Telefon Manualer

Nyeste Telefon Manualer

Kensington H3005 Manual

6 December 2025

HMD Barça 3210 Manual

4 December 2025

Panasonic KX-TS2350 Manual

29 November 2025

Huawei nova 14i Manual

23 November 2025

Soundcore Life P2 Manual

22 November 2025

Panasonic KX-TGE260 Manual

16 November 2025

Gigaset N530 IP PRO Manual

16 November 2025

Gigaset SL850H PRO Manual

12 November 2025

LG KG200 Manual

10 November 2025

Telycam SONO Manual

9 November 2025