Teradek Slice 776 Manual

Teradek Digitale decoder Slice 776

Læs gratis den danske manual til Teradek Slice 776 (2 sider) i kategorien Digitale decoder. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Teradek Slice 776, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Stream/Menu Control dial:

▲: Go live, start/stop push, start/stop recordings, select characters

, , : Selects options from streaming/recording prompts▼

: Back, move to higher menu level

● (Control dial button press): Confirm selection, enter main menu, open selected menu

▲

NETWORK CONNECTION

Connect A/C power to the Power Input . Attach the included Wireless antennas via the threaded (E)

RP SMA connectors .- (L)

Connect the SDI output from your video source to the HD SDI , or the HDMI input on the Slice -(F) (G)

encoder.

Connect Slice to your network via the 10/100/1000 Ethernet port .(H)

A: Power button

B: USB ports

C: Reset button

D: Stream/menu control dial

E: A/C input

F: SD/HD/3G−SDI input/output

G: HDMI input/output

H: 10/100/1000 Ethernet

I: Reset button

J: Headphone audio output

K: Mic/Line stereo input

L: RP SMA connectors-

E I

AC adapter

WiFi antennas

Connect to Slice’s Wi−Fi network (AP mode): Teranet−XXXXX (serial number of the device). If Slice has

already been configured to connect to another network (Infrastructure mode), connect to that instead.

Plug an Ethernet cable into Slice’s 10/100/1000 Ethernet port and connect it to an Ethernet switch

or router. Use the Menu joystick to navigate to the Network Setup menu, and verify that Ethernet is

enabled and set to DHCP.

Open a web browser and navigate to http://172.16.1.1, or find Slice using Bonjour.

Connect your computer to the same network as Slice. From the main status screen, press on Slice’s menu ▼

joystick to display Slice’s IP address on the front panel.

Slice’s Wi−Fi can also be configured to join your network via the web UI or front panel.

Open a web browser and navigate to Slice’s IP address, or find Slice using Bonjour.

Slice has a built in web user interface (web UI) for configuring stream destinations, encoder

parameters, and other settings. The interface can be accessed by connecting via Wi−Fi or Ethernet.

CONNECT VIA WI FI−

CONNECT VIA ETHERNET

Slice 700 series encoders support 1080p, 60fps encoding using both HEVC and H.264 codecs. HEVC

provides the most efficient encoding for both low bitrate and high quality applications, while H.264

supports a wider variety of streaming platforms and is one of the most common video codecs worldwide.

The codec can be switched between HEVC and H.264 from the Encoder Settings and Video Stream Output

settings pages on the web UI, or from the Video Setup menu on the front panel.

NEED MORE HELP?

1. Support: http://support.teradek.com Contains tips, information and all the latest firmware & software updates. →

TERADEK SUPPORT STAFF: support teradek.com or call 888 941 2111 ext2 (Mon Fri 9am to 6pm PST)@− − −

POWER AND CONNECT

HEVC AND H.264

STREAM TO THE INTERNET

RECORDING

Download VUER from the iTunes App Store.

Connect your iOS device to the same network as

Slice, then launch VUER.

From the VUER app, tap on the upper, left-hand CAMERA

corner, choose your device(s), then tap Done. VUER can

monitor up to four devices simultaneously (iPad Air and

newer).

• Recordings can be manually triggered via the front panel, or by the broadcast state in Internet

Streaming mode. Each time a broadcast starts, a new recording is created.

• If a broadcast is interrupted for connectivity reasons, recording continues.

• If a recorded file exceeds your storage media’s file size limits, a new file will be created and

recording continues.

• Recording resolution and quality matches your configured Broadcast settings.

Slice supports broadcast recording to an external USB drive. To enable recording:

RECORDING CONSIDERATIONS

DECODER SETUP

Insert a compatible USB drive into one of the USB ports . (B)

When prompted, select Yes to enable recording.

You can also enable or disable recording from the web UI.

Select the recording trigger you would like to use. Recordings can be triggered from a

compatible camera (ARRI/Canon, RED, or SONY), automatically when you begin a broadcast,

or manually via the control dial’s Select button. Once enabled, recordings are saved to the

selected storage media when triggered.

MONITOR WITH AN IOS DEVICE

Open Slice’s web UI, then select the Video Stream Output menu if it is not already displayed.

Select Internet Streaming as the Stream Mode and choose a platform − Facebook,

Ustream, Livestream, YouTube, Twitch − or select manual RTMP.

Open the Encoder settings menu and select your desired bitrate and resolution.

Enter your credentials and choose a channel/event, or enter the RTMP destination info and click Apply.

Go Live by clicking the Broadcast button , or press the front panel Stream Joystick.

Connect to Slice encoder (see previous sections) and open the web UI.

Open the Video Stream Output menu, then select MPEG Transport Stream as the streaming mode

(the protocol value will be set to UDP by default when you select MPEG Transport Stream).

Enter the decoder s IP address in the Host field, then set the port, if desired. The default port is 9710.'

Connect to Slice decoder (see previous sections) and open the web UI.

Open the Video Stream Source menu, then select MPEG Transport Stream as the streaming mode. Adjust

the protocol and port values so that they match the values entered in the Slice encoder’s web UI, then

click .Apply

Ensure that Slice’s encoder and decoder are on the same network. To configure:

NEED MORE HELP?

1. Support: http://support.teradek.com Contains tips, information and all the latest firmware & software updates. →

TERADEK SUPPORT STAFF: support teradek.com or call 888 941 2111 ext2 (Mon Fri 9am to 6pm PST)@− − −

Click .Apply

Produkt Specifikationer

Mærke:	Teradek
Kategori:	Digitale decoder
Model:	Slice 776
Bredde:	248.92 mm
Dybde:	431.8 mm
Højde:	43.2 mm
Vægt:	4082 g
Produktfarve:	Sort
Understøttede videotilstande:	480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Ethernet LAN-porte (RJ-45):	1
Antal USB 2.0-porte:	2
Understøttede videoformater:	H.264, H.265, HEVC
Ethernet LAN-datahastigheder:	10, 100 Mbit/s
Husmateriale:	Aluminium
Indgangsspænding for vekselstrømsadapter:	110 - 240 V
Strømforbrug (maks.):	8 W
Understøttede netværksprotokoller:	TCP/IP, UDP, HTTP, DHCP, NTP, SSL, IGMP
Maksimal videoopløsning:	- pixel
Ethernet-grænsefladetype:	Hurtigt ethernet
Antal kanaler:	- kanaler
Antal HDMI-udgange:	1
Stativ-montering:	Ja
Rackkapacitet:	1U
Strømforbrug (min.):	7 W