Tiptop Audio 245t Manual

Tiptop Audio Tastatur 245t

Læs gratis den danske manual til Tiptop Audio 245t (2 sider) i kategorien Tastatur. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om Tiptop Audio 245t, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

SEQUENTIAL VOLTAGE SOURCE - MODEL 245t

Eurorack 200 series

Buchla 245t has two sections: Pulser and Stored Voltage Stages.

SEQUENTIAL VOLTAGE SOURCE MODEL 245

advance

OUT

pulseanalog

PULSER

OUT

ref pulse

PULSE LENGTH

of period

0 100

INTERNAL TIME

.002

.005 .5

The Pulser generates

a control pulse which

can be used to

advance the stages

in the Voltage Stage

section.

The Voltage Stage

section has 5 stages

that store 4 voltages

per stage.

Pulser Section:

Pulse - output generates a pulse with a 10V initial stage that lasts for 100uSec (0.1ms) followed by a

5V gate stage length determined by the Pulse Length control.

Ref - outputs a ramp wave that descends from 10V to 0V at the rate of the pulser.

Pulse Length - sets the length of the 5V stage of the pulse from 0 to 100% of the duty cycle.

External CV control is added to the knob setting.

Internal Time - controls the period of the pulser output from 10 seconds (full CW) to a few

milliseconds (full CCW). External CV has an attenuverted control to either add (CW) or subtract

(CCW) external voltage from the knob setting. External CV can increase the maximum and

minimum period of the pulser to approximately 50 seconds to 1ms (1kHz) (*).

Start - Pressing this button starts generating a pulse and reference ramp at those outputs. A pulse

on the Start input also begins pulser generation.

Stop - Pressing the button or sending a pulse to the input jack stops the pulser if already running.

Additional presses or pulses to the Stop input will manually trigger a single pulse output from the

pulser.

PULSER

OUT

ref pulse

PULSE LENGTH

of period

0 100

INTERNAL TIME

.002

.005 .5

Eurorack 200 series

Ref Out 0 - 10V

Pulser Out 0 to 10V

Pulse Length CV 0 - 10V

Internal Time CV 0 - 10V

Start Pulse In 0 - 10V

Stop Pulse In 0 - 10V

SEQUENTIAL VOLTAGE SOURCE - MODEL 245t

SEQUENTIAL VOLTAGE SOURCE MODEL 245

advance

OUT

pulseanalog

Stored Voltage Stages:

Advance In - accepts a pulse from the Pulser or external source

(281t EOC for example) and each pulse advances to the next stage

from 1 to 5. The switches in the Stage Select section can control

the number of stages played back.

Note, with all stage switches in down position playback will be

on hold.

Stage Gate Output - Each stage has a dedicated gate output that

produces a high voltage (10V) when that stage is active. This gate

can be used to trigger events like envelopes.

Out - the voltage output of the current active stage. Each of the

outputs has an independent voltage.

Stored Voltages - 4 rows of 5 locations of stored analog voltages

set by a control knob.

Analog (In) - CV input (0-10V) that addresses the stages.

When the voltage is above the O range the Analog input is active

and the Advance and Stage Select Inputs are disabled.

Ranges are approximately(*): O (0V - 0.75V), Stage 1 (0.75V - 2.5V)

Stage 2 (2.5V to 4.25V) Stage 3 (4.25V to 6V) Stage 4 (6V to 7.75V)

Stage 5 (7.75V to 10V)

Stage Select Inputs - Pulses on these 5 inputs will immediately set

the active Stage to the corresponding input. Using these inputs

can create a type of analog preset memory for 4 CV settings in

your modular system.

Stage Switches - These 4 switches enable or disable the stage

transitions. Switch 1 controls Stage 1 to 2 transition, switch 2 Stage

2 to 3 and so on. By disabling a stage transition the length of the

sequence can be shortened or captured.

* Note: due to the analog nature of the design speciﬁcations for pulser timing and length and Analog In will slightly vary from

unit to unit.

Advance In 0 - 10V

Analog In 0 - 10V

Stage Select In 0 - 10V

Stored Voltage Out 0 - 10V

Stage Gate Out 0 - 10V

Size: 30HP - Depth: 25mm

Power: +12V 63mA / -12V 28mA

Speciﬁcations:

Produkt Specifikationer

Mærke:	Tiptop Audio
Kategori:	Tastatur
Model:	245t

Har du brug for hjælp?

Hvis du har brug for hjælp til Tiptop Audio 245t stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Tastatur Tiptop Audio Manualer

Tiptop Audio HATS808 Manual

13 August 2025

Tiptop Audio Mariana Trench Manual

13 August 2025

Tiptop Audio 207t Manual

13 August 2025

Tiptop Audio Z2040 Manual

12 August 2025

Tiptop Audio Trigger Riot Manual

12 August 2025

Tiptop Audio Chorus Manual

12 August 2025

Tiptop Audio µZEUS Manual

12 August 2025

Tiptop Audio Control Path Manual

7 Juli 2025

Tiptop Audio QART-QNTZ Manual

4 April 2025

Tiptop Audio SD808 Manual

4 April 2025

Tastatur Manualer

Nyeste Tastatur Manualer

Polyend Tracker Manual

15 September 2025

Kurzweil Artis 7 Manual

14 September 2025

Ibm ThinkPad UltraNav Manual

14 September 2025

AMX Metreau MET-13X Manual

14 September 2025

Kawai Z1000 Manual

14 September 2025

Kawai CP185 Manual

13 September 2025

Kawai MR380C Manual

13 September 2025

Ibm Fingerprint USB, US Manual

13 September 2025

Kawai P2500 Manual

13 September 2025

Kawai CP205 Manual

13 September 2025