TOA HY-CL10B Manual

TOA Højttaler HY-CL10B

Læs gratis den danske manual til TOA HY-CL10B (1 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 2 anmeldelser. Har du et spørgsmål om TOA HY-CL10B, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

133-01-00121-00

4.2. HY-CL20B

Mount all 4 speakers to the cluster bracket before suspending

them.

If conditions require that the cluster bracket be suspended first,

take s c l c e g a y g to t ce pe ia ar durin ssembl owin weigh balan

instability until all 4 speakers have been mounted.

Tip

The wall bracket supplied with each speaker is not used.

Step 1. h the ker t to the r of h of the 4 Attac spea bracke rea eac

s k cpea er abinets. Use t s she screw upplied wi he th t s ker. pea

(HY-CL10B: 2 x 4 HYpieces ; -CL20B: 4 pieces x 4)

Note

Mount the bracket so that the speaker is suspended in a

vertical orientation.

Step 2. Attach a joint bracket (4 brackets in total) to each of the 4

cluster bracket sections using the 16 screws supplied with

the cluster bracket.

Note

Before starting the work, ensure that all the screws used

for assembling the cluster bracket are firmly tightened.

Step 3. Mount the 4 speakers to the joint brackets.

Insert the speaker bracket into the joint bracket and put the

fixing bolt through the joint bracket.

Adjust each speaker's vertical orientation, then tighten the

fixing bolt.

The speaker angle can be adjusted in 7.5º steps within the

range as follows.

F-1000/2000 series: 15º to 45º downward

F-1300 series: 15º to 30º downward

Step 4. Lift the speaker cluster up to the installation position using

a suspension wire.

Step 5. ct e s ker s to e r t Conne th pea cable th speake inpu

terminals. For connections, refer to the instruction manual

enclosed with the speaker.

INSTALLATION MANUAL

CLUSTER BRACKET HY-CL10B

HY-CL20B

• re n or , be re to r y ad l e Befoinstallatio use su ca efull re al th

instructions in this section for correct and safe operation.

• Be sure to follow all the

precautionary instructions in this section,

whi on ai impor an warning and au ion regardinch c t n t t s /or c t s g

safety.

• After reading, keep this manual handy for future reference.

1. SAFETY PRECAUTIONS

Indicate potentiall haza dou situatio whis a y r s n ch, if

mishandled, could result in death or serious personal injury.

WARNING

• Refer all installation work to the dealer from whom the speaker

was purchased. Installation for flying requires extensive technical

knowledge and experience. The speaker may fall off if incorrectly

installed, resulting in possible personal injury.

• Flying Precautions

Be e to f w the t s w. se, the sur ollo ins ru ionct belo Otherwi

su pensio wire bel ma na an peas n s or ts y be off or s p d the s ker

may fall off, causing personal injury.

· Chec on ir ha uspensio wire an bel ark to c f m t t the s n s d ts e

strong enough to withstand the load.

· The c s of the s n s d ts st be onne orct su pensio wire an bel mu

securely linked with those of the load.

• Install the unit only in a location that can structurally support the

weight of the unit and the speaker. Doing otherwise may result in

the s r f g n d g l i y /or peake allin dow an causin persona njur and

property damage.

• S ce the t is s d for r use, do t l it in uni de igne indoo no in alst

outdoors. I

f d rs, e g of rts s e installe outdoo th agin pa cause th

speaker to fall off, resulting in personal injury.

• Owing to the speaker's size and weight, be sure that at least two

person ar availabl ins al uni ailur couls e e to t l the t. F e to do so d

result in personal injury.

• Do t e r s n f d to t e t. no us othe method tha speci ie moun th uni

Extreme force is applied to the unit and the speaker could fall off,

possibly resulting in personal injuries.

• Use nuts and bolts that are appropriate for the ceiling's structure

and composition. Failure to do so may cause the speaker to fall,

resulting in material damage and possible personal injury.

• Tighten each nut and bolt securely. Ensure that the unit has no

lo e jo ts a r i t la on to nt acci s at ld os in fte ns al ti preve dent th cou

result in personal injury.

• Use the specified speaker in combination. Doing otherwise may

cause the speaker to fall off, resulting in personal injury.

• Do not mount the unit in locations exposed to constant vibration.

Th uni ca damage ce ibration potentialle t n be d by ex ssive v , y

causing the speaker to fall, which could result in personal injury.

• Do not use anti-rust lubricant. If it

contacts resin or rubber parts,

t y d t te d e the t to f , s y he coul de eriora an caus uni all pos ibl

resulting in personal injury.

Indicate potentiall haza dou situatio whis a y r s n ch, if

mi handled oul resul modera mino personas , c d t in te or r l

injury, and/or property damage.

CAUTION

• Avoid touching the unit's sharp metal edge to prevent injury.

• Do not stand or sit on, nor hang down from the unit as this may

cause it to fall down or drop, resulting in personal injury and/or

property damage.

• Have the unit checked periodically by the shop from where it was

purchased. Failure to do so may result in corrosion or damage to

the t t t d se the t to f , s y c s g uni ha coul cau uni all po sibl au in

personal injury.

T h e H Y B t e r - C L 1 0 C l u s

Bracke allow totat s a l of 4

F / 0 S s s ker -1000 130 erie pea

sy em uspendest s to be s d

fro ceilin inglm a g in a s e

multi-directional cluster.

T h e H Y B t e r - C L 2 0 C l u s

Bra et is used r c s r ck fo lu te

c e i l i n su s p e n s i og n o f 4

F-2000 Series speakers.

2. GENERAL DESCRIPTION

[Finished assembling diagram]

4. SPECIFICATIONS

Note: The design and specifications are subject to change without

notice for improvement.

4.1. HY-CL10B

5. INSTALLATION

30°

15°

Speaker bracket

[F-1000/2000 series: 15° to 45° downward]

[F-1300 series: 15° to 30° downward]

Joint bracket

45°

30°

15°

Refer to the figures below for the positional relationship

between the speaker bracket's "groove" and the joint

bracket's "indentation."

Note

The mating surfaces of the speaker bracket and joint

bracket are designed to interlock.

Ensure that both parts are securely engaged with each

other after mounting is complete.

Fixing bolt

(supplied with the speaker)

Fixing bolt

(supplied with the speaker)

Speaker system

F-2000 series

Speaker system

F-1000 series

Speaker bracket

(supplied with the speaker)

Speaker bracket

(supplied with the speaker)

Screw M5 x 20

(supplied with the speaker)

Screw M5 x 20

(supplied with the speaker)

• HY-CL20B

• HY-CL10B

Joint bracket (supplied with the speaker)

Accessory screw M5 x 10

Suspension wire

Note

Use the outer 4 holes

for wire connections.

Suspension wire

Note

Use the outer 4 holes

for wire connections.

Cluster bracket HY-CL10B

Cluster bracket HY-CL20B

The figure at left

shows the screw

mounting positions

for the F-1300

series.

URL: http:// w. a.jp/ww to

Applic le Speakerab

F-2000B, F-2000BT, F-2000W, F-2000WT

Fi lanish Steel plate, b ck, paint

Dimensions

904 (w) x 395 (h) x 904 (d) mm

(Maximum dimensi s when the installed on

4 speakers face 37.5° downward)

Weight

27.4 kg (When 4 F-2 0Bs 0Ws are00 /200

clust ed)er

30 kg (When 4 F-2 0BTs 0WTs are00 /200

clust ed)er

Accessories

Machine screw M5 x 10 with washers … 16

Applic le Speakerab

F-1000B, F-1000BT, F-1000W, F-1000WT,

F-1300B, F-1300BT, F-1300W, F-1300WT

Fi lanish Steel plate, b ck, paint

Dimensions

492 (w) x 214 (h) x 492 (d) mm

(Maximum dimensions when the installed 4

F-1000 se es speakers face 30 downward)ri °

568 (w) x 263 (h) x 568 (d) mm

(Maximum dimensions when the installed 4

F-1300 serie speakers face 30 downward)s °

Weight

7.3 kg (When 4 F-100 000Bs/1 0Ws are

clust ed)er

8.1 kg (When 4 F-1 0BTs/1 0WTs are00 00

clust ed)er

12.5 kg (When 4 F-1300Bs/1300Ws are

clust ed)er

14.3 kg (When 4 F-1300BTs/1300WTs are

clust ed)er

Accessories

Machine screw M5 x 10 with w hers … 16as

Produkt Specifikationer

Mærke:	TOA
Kategori:	Højttaler
Model:	HY-CL10B
Bredde:	109.3 mm
Dybde:	109.3 mm
Højde:	39 mm
Produktfarve:	Sort
Materiale:	Stål

Har du brug for hjælp?

Hvis du har brug for hjælp til TOA HY-CL10B stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler TOA Manualer

7 Oktober 2025

7 Oktober 2025

7 Oktober 2025

7 Oktober 2025

TOA F-08WT-WP-UE Manual

7 Oktober 2025

7 Oktober 2025

7 Oktober 2025

7 Oktober 2025

7 Oktober 2025

7 Oktober 2025

Højttaler Manualer

Nyeste Højttaler Manualer

Tracer Powervox P1 TWS BT Manual

7 Oktober 2025

Russound Acclaim 5 Outback 5R82Mk2 Manual

7 Oktober 2025

Tracer Quasar TWS BT Manual

7 Oktober 2025

Blue Tees Golf Player Go Manual

7 Oktober 2025

Soundcore Rave 3S AI Manual

7 Oktober 2025

Klipsch Courtyard 4.1 Manual

7 Oktober 2025

Speco Technologies SPCBC5 Manual

7 Oktober 2025

Speco Technologies SP-8CLW Manual

7 Oktober 2025

SmallHD 1703 P3X Manual

7 Oktober 2025

Fusion MS-OS420 Manual

7 Oktober 2025