TOA HY-TB1 Manual

TOA Højttaler HY-TB1

Læs gratis den danske manual til TOA HY-TB1 (1 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om TOA HY-TB1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

1. SAFETY PRECAUTIONS

• Be sure to read the instructions in this section carefully before use.

• Make sure to observe the instructions in this manual as the conventions of safety symbols

and messages regarded as very important precautions are included.

• We also recommend you keep this instruction manual handy for future reference.

INSTALLATION MANUAL

TILE BAR BRIDGE HY-TB1

Please follow the instructions in this manual to obtain the optimum results from this unit.

We also recommend that you keep this manual handy for future reference.

Indicates a potentially hazardous situation which, if

mishandled, could result in death or serious personal

injury.

WARNING

Indicates a potentially hazardous situation which, if

mishandled, could result in moderate or minor personal

injury, and/or property damage.

CAUTION

• Leave the installation to your TOA dealer because the installation requires expert

knowledge. Improper installation may cause the speaker to fall, resulting in personal injury

and/or property damage.

• Install the mounting hardware in a location that can structurally support the weight of the

mounting hardware and the speaker. Doing otherwise may result in the speaker falling

down and causing personal injury and/or property damage.

• Do not use other methods than specified to mount the unit. Extreme force is applied to the

unit and the unit could fall off, possibly resulting in personal injuries.

• Tighten each screw securely. Ensure that the unit has no loose joints after installation to

prevent accidents that could result in personal injury.

• Use the specified speaker in combination. Doing otherwise may cause the speaker or

component to fall off, resulting in personal injury.

• Avoid touching the unit's sharp metal edge to prevent injury.

2. GENERAL DESCRIPTION

TOA's HY-TB1 Tile Bar Bridge is a 603 mm (23

/64") long support frame (set of 2 rails)

designed to provide secure support for flush-mounted ceiling speakers while preventing the

speaker's weight from being directly applied to the ceiling panels. Its support rails are

designed to act as mounts for the ceiling reinforcement ring supplied with each speaker.

Ceiling tile )rekaeps htiw deilppus( gnir tnemecrofnier gnilieCdirg-T

Reinforcement ring mounting screw

Tie-plate mounting screw

Tie-plate

(preinstalled on Bridge rail)

HY-TB1

(optional)

Bridge rail

Ceiling panel

Reinforcement ring mounting screw

Ceiling reinforcement ring (supplied with speaker)

Ceiling frame

max. 32 mm*

Tie-plate mounting screw

Tie-plate

(preinstalled on Bridge rail)

* This length can be extended to up to 58 mm by turning the tie-plate upside down.

HY-TB1

(optional)

Bridge rail

Before installation, a qualified architect or engineer should first determine whether the ceiling

frames and panels are strong enough to withstand the added weight of ceiling speakers.

Refer to the speaker's instruction manual for information.

[Completed installation figure]

•

For Dry Wall Ceilings

• For Drop Ceilings

3. SPECIFICATIONS

4. INSTALLATION

Note: The design and specifications are subject to change without notice for improvement.

Finish Steel plate, plating

Weight 500 g (2 pieces)

Usable Speaker F-122C, F-122CU, F-2322C, F-2352C, F-2852C

T-grid

600 mm tile HY-TB1

10° – 15°

Step 1. Install the HY-TB1 in the ceiling.

• For Dry Wall Ceilings

Insert the Tile Bridge rails through the mounting hole in the ceiling and lay them

across the ceiling frame in the orientation shown in the figure below. Loosen the two

reinforcement ring mounting screws in each tie-plate to the point that they do not fall

out of their holes.

Note: Only install the Tile Bridge on ceiling frames that can structurally support the

full weight of the speaker(s) to be installed.

• For Drop Ceilings

[Mounting to 2-foot tiles]

Align the two bridge rails as shown

in the figure at right.

[Mounting to 600 mm tiles]

Align the two bridge rails diagonally

at an angle of 10° – 15°.

T-grid

2-foot tile

HY-TB1

Ceiling frame

Mounting hole

Reinforcement ring

mounting screws

(Leave these screws loose.)

Tie-plate

HY-TB1

F-122C, F-122CU,

F-2322C, F-2352C

F-2852C

ø200 mm (7

/ ")8

ø250 mm (9

/ ")32

Ceiling reinforcement

ring

Reinforcement ring mounting screw

Tie-plate

Fit closely to the back surface

of the ceiling panel.

3-1

3-2

Step 4. Align the ceiling reinforcement ring

with the mounting hole.

If the ceiling reinforcement ring does

not line up accurately with the ceiling

mounting hole, adjust its position by

e i t h e r l o o s e n i n g t h e t i e - pl a t e

mounting screws and sliding the tie-

plate into correct position, or by

sh ifting t he ti e-plate mount ing

screws to the appropriate holes in

the Tile Bridge rails. The ceiling

reinforcement ring can be moved in

the direction indicated by the arrows.

Note

Be sure to tighten the tie-plate mounting screws after completing the adjustment.

Step 2. Install the ceiling reinforcement ring

supplied with the speaker.

To insert the reinforcement ring

through the ceiling mounting hole,

first fold the ring in half, then insert it

through the mounting hole and

re-open it with its tabs facing up.

Align the ring with the mounting hole.

Step 3. Attach the ceiling reinforcement

ring to the each tie-plate .

Note

Tighten the reinforcement ring

mounting screws while pressing

the ceiling reinforcement ring

snugly against the back surface

of the ceiling panel.

URL: http://www.toa.jp/

133-01-00126-00

Ceiling reinforcement

ring

Tie-plate mounting screw

Tie-plate

Mounting hole

Ceiling reinforcement ring

(supplied with speaker)

Reinforcement ring placed on ceiling panel

These tabs must

face upward,

away from the hole.

Produkt Specifikationer

Mærke:	TOA
Kategori:	Højttaler
Model:	HY-TB1

Har du brug for hjælp?

Hvis du har brug for hjælp til TOA HY-TB1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler TOA Manualer

TOA PE-154BS Manual

10 Oktober 2025

TOA TZ-406BWP AS Manual

10 Oktober 2025

TOA CS-761BS-W Manual

10 Oktober 2025

TOA BS-4W Manual

10 Oktober 2025

TOA TZ-606W AS Manual

10 Oktober 2025

TOA BS-634T Manual

10 Oktober 2025

TOA TZ-200BS Manual

10 Oktober 2025

TOA TZ-606WWP AS Manual

10 Oktober 2025

TOA PC-275AB-EB Manual

10 Oktober 2025

TOA CS-761B Manual

10 Oktober 2025

Højttaler Manualer

Nyeste Højttaler Manualer

Energy Sistem TempoRave Manual

11 December 2025

RCF C 5215-W MKIII Manual

10 December 2025

RCF X 28 L Manual

10 December 2025

Fostex PM0.4d Manual

8 December 2025

Amphion Argon 3LX Manual

8 December 2025

Amphion Argon 7LX Manual

8 December 2025

8 December 2025

8 December 2025

7 December 2025

7 December 2025