TOA SR-TB3 Manual

TOA Højttaler SR-TB3

Læs gratis den danske manual til TOA SR-TB3 (1 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 2 anmeldelser. Har du et spørgsmål om TOA SR-TB3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

INSTALLATION MANUAL

WALL TILT BRACKET SR-TB3

The SR-TB3 is a Wall Tilt Bracket designed to install the Line Array

Speaker SR-H2L, SR-H2S, SR-H3L or SR-H3S vertically on a wall.

It allows the speaker direction angle to be adjusted in the range of

0° to 5° downward and 0° to 15° leftward or rightward.

2. SPECIFICATIONS

Note: The design and specifications are subject to change without

notice for improvement.

Note: Only 1 speaker can be installed using the SR-TB3.

Step 1. Assemble the Bracket base, then install it on a wall.

1-1. Attach the Brackets A and B loosely to the Joint bracket to

make up a bracket base.

Determine Bracket A and B mounting positions (top or

bottom) depending on which the speaker is to face left or

right.

Note

The figure below shows an example when facing the

speaker rightward. Change the mounting positions of the

Brackets A and B with each other when facing the speaker

leftward.

Hex bolt M6 x 16

(supplied with the SR-TB3)

Bracket A

Note: Fix the bolts loosely.

Bracket A

Joint bracket

Bracket B

Wall

Note:

Overhead view of the speaker

Joint bracket

Horizontal angle: 15°

Speaker

1-2. Install the Bracket base on a wall.

1-3. Determine the speaker's horizontal angle by adjusting the

angle of Joint bracket.

Horizontal angle can be adjusted from 0° to 15°. After the

speaker's horizontal direction has been determined,

securely tighten 4 bolts loosely fitted in Step 1-1.

Step 2. Attach the Speaker mounting bracket to the speaker's

rear surface.

2-1. Remove the specified screws on the speaker's rear

surface, then use their screw holes to secure the Speaker

mounting. In this event, the removed screws are not used.

Unit: mm (inches)

4-ø7

(4-ø0.28)

40 (1.57)

278 (10.94)

WARNING

Bracket

Joint bracket

Bolts and nuts used to fix a

bracket base on a wall are

not included.

Use bolts and nuts that are

appropriate for the wall

material and structure.

Bracket base wall mounting dimensions

Speaker mounting bracket mounting position

[SR-H2L]

Speaker mounting

bracket

Hex bolt M5 x 25

(supplied with the SR-TB3)

Note

Remove the attached screws.

The removed screws are not used.

[SR-H2S] [SR-H3L] [SR-H3S]

502.2 (19.78)

422.2 (16.62)

718.2 (28.28)

680.2 (26.78)

Unit: mm (inches)

Speaker mounting bracket

About 5 – 7 mm (0.2" – 0.3")

Hex bolt M6 x 16

(supplied with the SR-TB3)

Fix the hex bolts leaving about 5 – 7 mm

(0.2" – 0.3") protruding.

Speaker (rear)

Step 3. Install the speaker body to the Joint bracket.

3-1. Insert the hex bolts loosely fitted to the Speaker mounting

bracket into the Joint bracket's slots.

3-2. Fix the Speaker mounting bracket to the Joint bracket

loosely with the 4 supplied hex bolts.

Step 4. Connect the speaker cable to the removable terminal

plug.

For connection, refer to the instruction manual enclosed

with the speaker.

Step 5. Adjust the downward angle by moving the speaker

body.

Downward angle can be adjusted from 0° to 5°.

After the speaker's vertical direction has been determined,

securely tighten 6 bolts loosely fitted into the Speaker

mounting bracket.

Joint bracket

Insert into the Joint

bracket's slots.

Speaker mounting bracket

Removable terminal plug

-2

-1

Hex bolt M6 x 16

(supplied with the SR-TB3)

Speaker

Joint bracket

Speaker mounting

bracket

Hex bolt

0° to 5°

These screws (one each on both sides)

serve as fulcrums, on which speaker

downward angle can be adjusted.

2-2. Fix 2 hex bolts (one each) loosely in the

center bolt-holes on both sides of the

Speaker mounting bracket.

133-05-446-40

URL: http://www.toa.jp/

1. SAFETY PRECAUTIONS

3. INSTALLATION

• Before installation or use, be sure to carefully read all the

instructions in this section for correct and safe operation.

• Be sure to follow all the precautionary instructions in this section,

which contain important warnings and/or cautions regarding

safety.

• After reading, keep this manual handy for future reference.

• Install the unit only in a location that can structurally support the

weight of the unit and the speaker. Doing otherwise may result in

the unit falling down and causing personal injury and/or property

damage.

• Since the unit is designed for in-door use, do not install it

outdoors. If installed outdoors, the aging of parts causes the unit

to fall off, resulting in personal injury.

• Do not use other methods than specified to mount the bracket.

Extreme force is applied to the unit and the unit could fall off,

possibly resulting in personal injuries.

• Use nuts and bolts that are appropriate for the wall material and

structure. Failure to do so may cause the speaker to fall, resulting

in material damage and possible personal injury.

• Tighten each nut and bolt securely. Ensure that the bracket has

no loose joints after installation to prevent accidents that could

result in personal injury.

• Use the specified speaker in combination. Doing otherwise may

cause the unit or component to fall off, resulting in personal injury.

• Do not mount the unit in locations exposed to constant vibration.

The mounting bracket can be damaged by excessive vibration,

potentially causing the unit to fall, which could result in personal

injury.

• Avoid touching the unit's sharp metal edge to prevent injury.

• Do not stand or sit on, nor hang down from the unit as this may

cause it to fall down or drop, resulting in personal injury and/or

property damage.

• Have the unit checked periodically by the shop from where it was

purchased. Failure to do so may result in corrosion or damage to

the unit or speaker that could cause the unit to fall, possibly

causing personal injury.

WARNING

Indicates a potentially hazardous situation which, if

mishandled, could result in death or serious personal injury.

CAUTION

Indicates a potentially hazardous situation which, if

mishandled, could result in moderate or minor personal injury,

and/or property damage.

Applicable Speaker SR-H2L, SR-H2S, SR-H3L, SR-H3S

Finish Rolled steel plate, white, paint

Dimensions 64 (w) x 296 (h) x 50 (d) mm

(2.52" x 11.65" x 1.97")

Weight 1.4 kg (3.09 lb)

Component Speaker mounting bracket ............. 1,

Bracket A ........... 1, Bracket B ...... 1,

Joint bracket ...... 1

Accessories Hex bolt M5 x 25 (with washer) .......... 4

Hex bolt M6 x 16 (with washer) ........ 10

Produkt Specifikationer

Mærke:	TOA
Kategori:	Højttaler
Model:	SR-TB3
Bredde:	64 mm
Dybde:	50 mm
Højde:	296 mm
Vægt:	1400 g
Produktfarve:	Hvid
Materiale:	Stål
Hældningsvinkelområde:	-5 - 15 °
Kapabilitet:	SR-H3S, SR-H3L, SR-H2S, SR-H2L