Totolink EX200 Manual

Totolink Wifi repeater EX200

Læs gratis den danske manual til Totolink EX200 (1 sider) i kategorien Wifi repeater. Denne vejledning er vurderet som hjælpsom af 58 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 29.5 anmeldelser. Har du et spørgsmål om Totolink EX200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

For more information, please go to www.totolink.net

Product Introduction

Method One: Quick Setup by Smart Phone

FAQ(Frequently Asked Questions)

Method Two: Wi-Fi Extension by WPS Button

Power on. Plug the device into any wall

socket that near the router. Wait until the

System LED blinks slowly.

1Press WPS button on Extender for about 2 seconds.

SSID: TOTOLINK_EX200

The Extend LED flash when

connecting and turns to solid

light when connected

Press WPS button on your router for about 2 seconds.

RST/WPS

Wi-Fi: Upper router’s SSID and password

The Extend LED turns to solid light, Wi-Fi extension successful. Please refer to to place the Extender.Relocate

EX200's default Network Name (SSID) is TOTOLINK_EX200 (no encryption).

With success repeater connection, this SSID (TOTOLINK_EX200) will change

to the same SSID (with same encryption) of upper Router/AP. After deployment,

just connect to the Router/AP's SSID. Congratulations, you have extended your

WiFi coverage successfully.

What should I do if I cannot access the extender’s web management

page?

A1: Make sure you have connected to the wireless network name of

the extender.

A2: Open any browser, enter 192.168.0.254 in the address bar and

press Enter.

A3: Reset the extender and connect to it again.

How to reset the extender to factory default settings?

Keep the extender power on, use a pin to press the RST button

on the bottom of device. When both System and Extend LED blinks,

release the button. The device will restore to factory default settings.

Quick Installation Guide

Wireless N Range Extender

Model No.: EX200

V1.0 | 1712

Information in this document is subject to change without prior notice.

On: The device is starting up or waiting for

extending.

Slow-blinking: The device is working normally.

Quick-flashing: The device is to restart.

Off: The device is power off.

On: Extending successfully.

-Good; -Normal; -Bad.Green Yellow Red

Slow-blinking: The device is extending to

upper Router/AP.

Quick-flashing: The device is to restart.

Off: No extending.

WPS: Press the button for about 2-3 seconds

to enable WPS.

LAN port: This port is used to connect to PC.

RST: Press the button for about 10 seconds, the

device will restore to factory default settings.

RST

Power on. Plug the device into any wall

socket that near the router. Wait until the

System LED blinks slowly.

1Connect to the Extender. Using your

smart phone to search Wi-Fi

TOTOLINK_EX200. (Settings—Wi-Fi)

2Login. The Setting page will turn up automatically.

Click . If below window doesn’tExtender Mode

appear, please open a browser and enter

192.168.0.254 manually.

3Extend Wi-Fi. Wait for a while, the Extender

auto-detects APs nearby. Choose your

router’s 2.4GHz SSID.

4 6 Verify. Check the LED status to verify

whether the Wi-Fi extension is

successful.

Configure . Enter its wireless password. Either keep

the default SSID or customize it for extended 2.4GHz

wireless network. Verify your settings and click Connect.

Relocate

Horizon Line

Host Network Extended Network

Vertically place the Extender

Wall Socket

Plug the extender into wall socket that halfway between your

router and the Wi-Fi dead zone. Wait about 30 seconds until

the Extend LED light turns solid green or yellow. If not, please

relocate it closer to your router to achieve better signal quality.

In order to make full use of extender, please keep the antennas

of the extender perpendicular to the horizontal plane. See blow:

Produkt Specifikationer

Mærke:	Totolink
Kategori:	Wifi repeater
Model:	EX200
Type:	Netværkssender & -modtager
Produktfarve:	Hvid
Wi-Fi:	Ja
Opbevaringstemperatur (T-T):	-40 - 70 °C
Relativ luftfugtighed ved drift (H-H):	5 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	5 - 90 %
Ethernet LAN-porte (RJ-45):	1
Wi-Fi-standarder:	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Driftstemperatur (T-T):	0 - 40 °C
Ethernet LAN-datahastigheder:	10, 100 Mbit/s
Sikkerhedsalgoritmer:	64-bit WEP, 128-bit WEP, WPA-PSK, WPA2-PSK
Husmateriale:	Acrylonitrile butadiene styrene (ABS), Plastic, Polycarbonate (PC)
Hurtig start guide:	Ja
Kabler inkluderet:	LAN (RJ-45)
Wi-Fi-bånd:	Enkelt band (2,4 GHz)
Kabelteknologi:	10/100Base-T(X)
Netværksstandarder:	IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
DHCP-klient:	Ja
DHCP-server:	Ja
Antenner, antal:	2
Webbaseret administration:	Ja
Knap til nulstilling:	Ja
WPS trykknap:	Ja
LED-indikatorer:	System, WLAN
Udgangsspænding:	5 V
Udgangsstrøm:	1 A
Værtsgrænseflade:	RJ-45
Wi-Fi-datahastighed (maks.):	300 Mbit/s
Antenne type:	Ekstern
Plug and play:	Ja
Maksimal overførselsafstand:	30 m
Niveau for antennestyrke (maks.):	4 dBi
Dataoverførselshastighed:	300 Mbit/s
Auto MDIX IEEE:	Ja