TP-Link Omada EAP650-Desktop Manual

TP-Link Ikke kategoriseret Omada EAP650-Desktop

Læs gratis den danske manual til TP-Link Omada EAP650-Desktop (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 15 anmeldelser. Har du et spørgsmål om TP-Link Omada EAP650-Desktop, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Quick Installation Guide
Desktop Access Point
Note: This guide uses EAP650-Desktop for demonstration. Images may dier from your actual product.
©2024 TP-Link 7106511611 REV1.0.1
*
When the Locate feature is activated in the Omada Controller, the System LED will ash quickly for 10
minutes to help you locate and identify the device. You can disable this feature manually to stop the device
from ashing.
**
802.3at/bt PoE input is required. 802.3af and passive PoE inputs will disable 5 GHz band and PoE output and
thus not recommended.
***
The device can supply PoE output power only when it is receiving 802.3at/bt PoE input power.
Blue On: Power supply is normal.
Flash Orange: Power supply is insucient.
O: Power is o, or LEDs are turned o.
LED Indication
Power
System
On: The EAP is initializing or working normally.
O: The EAP is working abnormally.
Flash: • Flash Twice: Initialization is complete.
• Flash Once per Second: The EAP is upgrading or resetting.
• Quick Flash: The Controller is locating the EAP.*
• Sustained Flash: The EAP is in the isolated state.
On: The SIP account is registered successfully.
Slow Flash: The phone is o hook.
Quick Flash: The phone is ringing.
O: No SIP account is registered.
FXS
Green On: The port is receiving 802.3bt PoE power.
Orange On: The port is receiving non-802.3bt PoE power**.
O: The port is not connected or not receiving PoE power.
On: The port is supplying power to a PoE powered device.
O: The port is not connected or not supplying power.
IN
(ETH0)
OUT
(ETH1)
On: The port is linked but has no activity.
Flash: The port is transmitting or receiving data.
O: The port is not linked.
Link/Act
(ETH0~ETH3)
With the EAP powered on, press and hold the button for about 5
seconds until the System LED ashes, then release the button.
The EAP will restore to factory settings.
Press the button to turn on/o the LEDs.
Button Description
RESET
LED
Connect to a power socket via the provided power adapter.
Connect to a power sourcing equipment for both data
transmission and PoE input**.
Connect to a PoE powered device for both data transmission and
PoE output***.
Connect to a client device to transmit data.
Connect to a phone to make and receive calls over the internet.
Interface Description
Power
ETH0
(PoE IN)
ETH1
(PoE OUT)
ETH2 ~ ETH3
FXS
Business CommunityDownload CenterSetup Videos
The EAP can only be powered by a power adapter, or by a PSE device (such as a PoE switch) that complies with Power Source Class 2 (PS2) or
Limited Power Source (LPS) defined in the standard of IEC 62368-1.
Note: For power supply specifications, refer to the product label.
Option 1: Power by PoE Switch Option 2: Power by Power Adapter
Phone
Internet
Connect to FXS port
Connect to ETH0 (PoE IN) port
PoE Switch
Power Adapter
Internet
Connect to Power port
Connect to an Ethernet port
Connect to FXS port
Phone
Hardware Connection
2
Option 1: Desktop Mounting
1. Attach the EAP to the provided multi-functional base as shown in
the figure.
Option 2: Wall Mounting
1. Secure the provided multi-functional base to the wall in the correct
direction with the provided screws.
2. Attach the EAP to the base as shown in the figure.2. Place the EAP vertically on a horizontal surface (such as a desktop
or shelf) that is out of children’s reach.
Hardware Installation
3
Hardware Overview
1
Safety Information
• Keep the device away from water, re, humidity or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need
service, please contact us.
• Do not use the device where wireless devices are not allowed.
• Do not use damaged charger or USB cable to charge the device.
• Do not use any other chargers than those recommended.
• Adapter shall be installed near the equipment and shall be easily
accessible.
• The PoE ports shall not be used to charge lithium batteries or devices
supplied by lithium batteries.
EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/53/EU,
2009/125/EC, 2011 /65/EU and (EU) 2015/863.
The original EU Declaration of Conformity may be found at
https://www.tp-link.com/en/support/ce/
UK Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Radio Equipment
Regulations 2017.
The original UK Declaration of Conformity may be found at
https://www.tp-link.com/support/ukca/
Set Up4
Choose a method to set up your EAPs:
• Method 1: Standalone Mode
Congure and manage EAPs separately (Convenient for a small network
with only a few devices)
• Method 2: Controller Mode
Congure and manage EAPs in batches on a central platform, namely the
Omada Controller.
1. Get an Omada Controller ready.
• Option 1: Omada Hardware Controller
Purchase a Hardware Controller and refer to its Installation Guide to set it
up.
• Option 2: Omada Software Controller
On a PC with Windows or Linux OS, download the Software Controller from
https://www.tp-link.com/support/download/omada-software-controller/.
Then run the file and follow the wizard to set up the Controller.
Note: To manage your devices, the Software Controller needs to keep running on your
PC.
• Option 3: Omada Cloud-Based Controller
Go to the Omada Portal (https://omada.tplinkcloud.com) and log in with
your TP-Link ID. Then click + Add Controller to add a Cloud-Based
Controller and set it up.
2. Launch the Controller, access your site, and go to the Devices page.
3. Now you can adopt and manage the EAPs.
4. (Optional) Configure the phone service.
Go to Settings > VoIP to configure the phone service with the information
provided by your telephony service provider. For detailed instructions, refer to
your Controller’s user guide.
Tip: For the Omada Hardware/Software Controller, you are recommended to enable Cloud
Access and bind it to your TP-Link ID. This enables you to remotely access and manage the
Controller and Omada devices via the Omada Portal (https://omada.tplinkcloud.com).
For detailed configurations, refer to the User Guide of the Controller at our
official website: https://www.tp-link.com/support/download/?type=smb
Via Web Browser
2. Add the Controller with local access or cloud access.
• Local Access
Note: Local access applies to the Hardware Controller and Software Controller
only.
a. Connect your mobile device to the EAP by using the default SSIDs
printed on the label of the product.
b. Launch the Omada App and go to Controller - Local Access. Tap the +
button on the upper-right corner to add the Controller.
• Cloud Access
a. Controller - Cloud Access Launch the Omada App and go to .
b. Log in with your TP-Link ID. A list of Controllers that have been bound
with your TP-Link ID will appear.
3. Launch the Controller, access your site, and go to the Devices page.
4. Now you can adopt and manage the EAPs.
The Omada App is designed to help you quickly configure common
settings. If you want to configure advanced settings (such as phone
service), use the web page of your Controller.
1. Download and install the TP-Link Omada App from App Store or Google
Play.
2. Connect your mobile device to the EAP by using the default SSIDs printed
on the label of the product.
3. Launch the Omada App, go to the page, and Standalone Mode > EAPs
wait for the EAP to appear. Tap on the EAP to configure it.
The Omada App is designed to help you quickly configure common
settings. If you want to configure advanced settings (such as phone
service), use the web page of your EAP.
Scan for Omada Omada
or
Via Omada App
Via Web Browser
1. Connect your device to the EAP by using the default SSIDs printed on the
label of the product.
2. Launch a web browser and enter https://tplinkeap.net in the address bar.
Use admin for both Username and Password to log in.
3. Set up a new Username and Password for secure management. Then you
can configure the AP.
4. (Optional) Configure the phone service.
Go to the Telephony page and set up the telephone number with the
information provided by your telephony service provider. Now you can
make phone calls over the internet.
https://tplinkeap.net
Method 1: Standalone Mode
Notes:
• Before you start, be sure to power up and connect your devices according to the
topology gure.
• A DHCP server (typically a gateway/router with the DHCP function enabled) is required
to assign IP addresses to the EAPs and clients in your local network.
If your network has only a few devices, you can congure and manage EAPs
separately on their web pages.
Note: The EAP web page is inaccessible while the EAP is managed by a Controller.
Clients
SwitchGateway/Router
EAP
EAP
EAP
Phone
SIP Server
For technical support, the user guide and other information,
please visit https://www.tp-link.com/support/?type=smb,
or simply scan the QR code.
For detailed configurations, refer to the user guides of the Controller and
EAPs. The guides can be found on the Download Center of our official
website: https://www.tp-link.com/support/download/?type=smb.
Method 2: Controller Mode
Notes:
• A DHCP server (typically a gateway/router with the DHCP function enabled) is required to
assign IP addresses to the EAPs and clients in your local network.
• The Omada Controller must have network access to your Omada devices (the
gateways/routers, switches, and EAPs) in order to nd, adopt, and manage them.
Omada Controller integrates Omada gateways/routers, switches, access points,
and more for centralized management.
Clients
SwitchGateway/Router
EAP
EAP
EAP
EAP
Omada
Hardware/Software
Controller
Omada
Cloud-Based
Controller
Or
Controller
Phone
SIP Server
1. Download and install the TP-Link Omada App from App Store or Google Play.
Scan for Omada Omada
or
Via Omada App

Produkt Specifikationer

Mærke: TP-Link
Kategori: Ikke kategoriseret
Model: Omada EAP650-Desktop

Har du brug for hjælp?

Hvis du har brug for hjælp til TP-Link Omada EAP650-Desktop stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret TP-Link Manualer

TP-Link

TP-Link Omada SM5110LSA-10 Manual

14 Juli 2025
TP-Link

TP-Link DeltaStream DS-P7500-16 Manual

11 Juli 2025
TP-Link

TP-Link UE302C Manual

5 Juli 2025
TP-Link

TP-Link RE1750X Manual

1 Juli 2025
TP-Link

TP-Link Archer TBE6500U Manual

27 Juni 2025
TP-Link

TP-Link RE765X Manual

26 Juni 2025
TP-Link

TP-Link Archer TBE3600U Manual

26 Juni 2025
TP-Link

TP-Link Deco BE68 Manual

26 Juni 2025
TP-Link

TP-Link DS-PMA-C+ Manual

26 Juni 2025
TP-Link

TP-Link RE405BE Manual

26 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Asrock

Asrock Rack SPC621D8 Manual

16 Juli 2025
For.A

For.A FA-10DCCRU Manual

16 Juli 2025
CYP

CYP AU-DTO4-RX Manual

16 Juli 2025
Levenhuk

Levenhuk Zeno Lamp ZL23 Manual

16 Juli 2025
Motorola

Motorola MiT3000 Manual

16 Juli 2025
Hillvert

Hillvert HT-PT-360 Manual

16 Juli 2025
CYP

CYP PUV-1610RX Manual

16 Juli 2025
Rockville

Rockville RM50RT-B Manual

16 Juli 2025
DS18

DS18 RCNLP/BK Manual

16 Juli 2025
CYP

CYP EL-7500V Manual

16 Juli 2025