TP-Link Tapo D235 Manual

TP-Link Overvågningskamera Tapo D235

Læs gratis den danske manual til TP-Link Tapo D235 (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 72 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 36.5 anmeldelser. Har du et spørgsmål om TP-Link Tapo D235, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

*Images may dier from your actual product.7106511276 REV1.0.1

Video Doorbell Camera

Quick Start Guide

Tapo

Take care to avoid electric shocks. *Recommended Installation Height: 1.2 m (4 ft) above the ground

Install Your Doorbell

03 /

Option 1. Stick to the wall

1. Attach the included adhesive to the back of the bracket or the wedge you have selected. If you use the

wedge, ax the bracket and the wedge with screws.

2. Route the wires through the bracket (if there are existing wires) . Wipe o the dust from the surface using

a dry cloth, stick the bracket with adhesive to the smooth wall, and press it down for 15 seconds to

ensure the bracket is rmly attached.

Note: This is applicable with tile, glass, marble, metal, stainless steel, and smooth wall surfaces.

Mounting Wedge3M Adhesive3M Adhesive

Requires:

• Mounting Bracket

• 3M Adhesive

Note: The adhesive is for one-time use. Avoid re-using the adhesive to ensure its adhesion.

Requires:

• Mounting Bracket

• 3M Adhesive

• Horizontal or Vertical

Mounting Wedge

• Mounting Wedge

Screws ×4

Flip the page over for , and more. Option 2

5V/2A USB Charger

Set Up Your Doorbell and Chime

2. Download the Tapo app from the App Store or

Google Play.

3. Press and hold the button on the back of ON/OFF

the doorbell for to turn it on.3 seconds

1. Plug in the USB cable to charge your doorbell.

When you plug in the charger, the LED should

blink amber quickly for 3 seconds.

4. Tap the button in the app and select your

model. Follow the app instructions to set up your

doorbell and pair with the chime.

Note: If you didn’t pair the chime during the setup, please

refer to https://www.tp-link.com/support/faq/3818/.

1. Turn o the circuit breaker. Make sure the power is

o by ringing your doorbell a few times.

OFF

01 / Install Jumper Wire for Your Existing Chime

Take care to avoid electric shocks.

2. Remove the chime cover and take a photo of the

wiring in case you want to reconnect it.

4. Tighten the screws and replace the chime cover. If

you want to disable Always-On Mode, just remove the

jumper wire.

Note: If your doorbell chime has dierent markings, consult a

licensed electrician.

3. Slightly loosen the screws for the and of Front Trans

your doorbell or the and of your front Rear Trans

rear doorbell, then insert the included jumper wire.

Front Doorbell

TRANS TRANSREARFRONT

Rear Doorbell

Preparations for Installing Your Doorbell

02 /

1. Remove your existing doorbell on the door. Then

disconnect the wires.

2. (Optional) Select the mounting wedge to adjust the

viewing angle of the doorbell.

Without Mounting

Wedge

With Vertical

Mounting Wedge

Without Mounting

Wedge

With Horizontal

Mounting Wedge

15°

5°

Mount Your Doorbell

Note:

1. Charge the doorbell before use. This will take about 6 hours.

2. The USB charger is not provided.

3. Peel o lm from the doorbell before use.

4. Warning: Do not tear o the silicone part by force as it may aect

the waterproof performance.

5. Keep the ports rmly covered when not in use to ensure

waterproof performance.

Option A: Battery Powered Option B: Hardwire Powered

If you don’t have existing doorbell wiring at the door,

use the built-in battery. You are free to determine

the doorbell position and the mounting is easy and

quick.

When the doorbell battery level is low, you need to

detach and charge it.

For installation, skip 01/ Install Jumper Wire for

Your Existing Chime and choose either installation

option to install your doorbell without existing wires.

Determine Power Options

You can choose whether to enable Always-On

Mode, which supports 24/7 recording.

WARNING: Risk of Electric Shocks

• Your existing doorbell must be wired (not battery

powered) and supplied by an 8-24V AC, 10VA

minimum transformer.

• Ensure that your existing doorbell works by ringing

the doorbell.

• Locate your existing doorbell chime.

• Disconnect power at the fuse or circuit breaker

before installing.

• You can always nd detailed wiring and installation

instructions in the Tapo app.

8-24V

Enabling requires bypassing Always-On Mode

your existing chime.

For installation, follow instructions in the Mount

Your Doorbell section to bypass your existing

chime and install your doorbell.

Disabling allows using your Always-On Mode

existing chime. Hardwiring provides a constant

power source.

For installation, skip 01/ Install Jumper Wire for

Your Existing Chime and then install your doorbell.

(Only necessary when hardwiring the doorbell and enabling Always-On Mode.)

3. Mount the doorbell to the bracket.

Option A: Battery Powered

Mount the doorbell to the bracket.

Requires:

• Video Doorbell Camera Note: If the wires are too short, use the included extension

wires and wire nuts to make them longer.

If the wires are too short:

Requires:

• Video Doorbell Camera

• (Optional) Extension Wires ×2, Wire Nuts ×2

Option B: Hardwire Powered

Connect the wires to the doorbell and tighten the

screws. Mount the doorbell to the bracket and turn on

the circuit breaker.

Setup Video

Scan QR code or visit

https://www.tp-link.com/support/

setup-video/#cloud-cameras

Doorbell Appearance

Option 2. Mount to the wall

1. Route the wires (if there are existing wires) through the mounting template and stick the template. Drill two

holes where indicated.

Note: When mounting to uneven walls, stick the foam pad on the back of the bracket or wedge.

2. Route the wires (if there are existing wires) through the bracket. Insert two anchors into the holes and use the

screws to ax the bracket over the anchors.

Φ=6 mm (15/64 in.)

Requires:

• Mounting Template

Requires:

• Mounting Anchors ×2

• (Optional) Foam Pad

• (Optional) Horizontal or

Vertical Mounting Wedge

• Mounting Bracket

• Mounting Screws ×2

Mounting Wedge (Optional)Foam Pad (Optional)

Chime Appearance

• Use a pin to press and hold for : Reset Wi-Fi settings 5s

• Use a pin to press and hold for : Reset to factory 10s

settings

Reset Button

Speaker1

LED

Press to cycle through dierent ringtones.

Music Button5

Press to adjust the volume of the ring.

Volume Button

How to Detach Doorbell

Safety Information

Use the doorbell detaching pin provided if you wish to

detach the doorbell from the mounting bracket.

microSD

4LED

Lens

Light Sensor3

1Microphone

Motion Sensor (PIR)

Speaker6

Ring Button7

Press and hold for : Reset to factory settings5s

SYNC/RESET Button

microSD Card Slot10

Tear o the silicone cover and insert a microSD card.

Initialize it on the Tapo app before use.

*microSD card not included

Type-C Port11

Plug in the USB cable to charge your doorbell.

ON/OFF Button12

Press and hold for 3 seconds to turn on/o the doorbell.

• Never touch the product with wet hands.

• Do not disassemble, repair or modify the product.

• Do not use the device where wireless devices are not allowed.

• Do not use the product if the casing has been broken. Danger

of electric shock.

• Keep the device away from re or hot environments. DO NOT

immerse in water or any other liquid.

• The product can only be installed, disassembled and

maintained by instructed person or skilled person.

• Do not place near automatically controlled devices such as re

alarms. Radio waves emitted from this product may cause such

devices to malfunction resulting in an accident.

• Observe restrictions on using wireless products in fuel depots,

chemical plants or when blasting operations are in progress.

• Do not use liquid to clean the product. Only use a dry cloth.

• Never put metal objects inside the product. If a metal object

enters the product, turn o the circuit breaker and contact an

authorised electrician.

• This product is not intended to be used when providing medical

care. Consult the manufacturer of any personal medical devices,

such as pacemakers or hearing aids to determine if they are

adequality shielded from external RF (radio frequency) energy.

• Do not use this product in health care facilities. Hospitals or

health care facilities may be using equipment that could be

sensitive to external RF energy.

• Do not use this product near water for example near a bath tub,

wash bowl, kitchen sink or laundry tub, in a wet basement or near

a swimming pool.

• The product should be kept free from excessive smoke, dust

TP-Link hereby declares that the device is in compliance with the

essential requirements and other relevant provisions of directives

2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The

original EU declaration of conformity may be found at

https://www.tapo.com/support/ce/

TP-Link hereby declares that the device is in compliance with the

essential requirements and other relevant provisions of the Radio

Equipment Regulations 2017. The original UK declaration of

conformity may be found at https://www.tapo.com/support/ukca/

CAUTION!

Avoid replacement of a battery with an incorrect type that can

defeat a safeguard.

Avoid disposal of a battery into re or a hot oven, or

mechanically crushing or cutting of a battery, that can result in

an explosion.

Do not leave a battery in an extremely high temperature

surrounding environment that can result in an explosion or the

leakage of ammable liquid or gas.

Do not leave a battery subjected to extremely low air pressure

that may result in an explosion or the leakage of ammable

liquid or gas.

Doorbell LED Indication

Doorbell updating

Doorbell resetting

Ready for setup

Connecting to Wi-Fi

Connected to the cloud

Blinking red and green

Solid red

Blinking white quickly

Blinking red quickly

Blinking red slowly

Solid white

Solid amber Connected to Wi-Fi

Starting up

Charging the doorbell

Blinking amber quickly

for 3 seconds

Chime LED Indication

Blinking red and green

Blinking red slowly

Solid green

Solid red

Blinking green quickly

Solid amber

Starting up

Connected to the cloud

Ready for setup

Connecting to Wi-Fi

Connected to Wi-Fi

Chime updating

Please read and follow the above safety information when

operating the device. We cannot guarantee that no accidents or

damage will occur due to improper use of the device. Please use

this product with care and operate at your own risk.

For EU/UK Region:

Operating Frequency / Max Output Power:

2400MHz~2483.5MHz / 20dBm

or high temperature and vibration.

• This product should not be exposed to direct sunlight.

• Do not place heavy objects on top of the product.

• This product may interfere with other electronic products such

as TV, radios, personal computers, phones or other wireless

devices.

• This equipment can be powered only by equipment that

complies with Power Source Class 2 ( PS2) or Limited Power

Source(LPS) dened in the standard of IEC 62368-1.

• This equipment shall be installed at a height of fewer than 2

meters when sticking to a clean wall.

• Doorbell Operating Temperature: -20 °C ~ 45°C (-4°F ~ 113°F)

Chime Operating Temperature: 0 °C ~ 40°C (32°F ~ 104°F)

Need some help?

Visit https://www.tapo.com/support/

for technical support, the user guide, FAQs,

warranty & more

Anti-Theft Button

• Press and hold for 5s:

Pause the alarm (Continues to alarm when released)

• Press and hold simultaneously for 10s:

Disable the anti-theft alarm feature

When the Anti-Theft Alarm is enabled on the Tapo app, an

alarm will trigger once the doorbell is removed.

3. Mount the doorbell to the bracket.

Note: If the wires are too short, use the included extension

wires and wire nuts to make them longer.

If the wires are too short:

Requires:

• Video Doorbell Camera

• (Optional) Extension Wires ×2, Wire Nuts ×2

Option B: Hardwire Powered

Connect the wires to the doorbell and tighten the

screws. Mount the doorbell to the bracket and turn on

the circuit breaker.

Option A: Battery Powered

Mount the doorbell to the bracket.

Requires:

• Video Doorbell Camera

Note: If you have trouble attaching the doorbell to the bracket or it causes false anti-theft alarms, check if you tightened the

screws too much that the bracket bent. Adjust the depth of the screw and then reinstall the doorbell.

Produkt Specifikationer

Mærke:	TP-Link
Kategori:	Overvågningskamera
Model:	Tapo D235

Har du brug for hjælp?

Hvis du har brug for hjælp til TP-Link Tapo D235 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera TP-Link Manualer

TP-Link VIGI C355 Manual

26 Juli 2025

TP-Link Tapo D130 Manual

26 Juli 2025

TP-Link Tapo C125 Manual

25 Juli 2025

TP-Link Tapo C720 Manual

25 Juli 2025

TP-Link INSIGHT S345-4G Manual

25 Juli 2025

TP-Link VIGI C385 Manual

25 Juli 2025

TP-Link VIGI C445 Manual

25 Juli 2025

TP-Link VIGI C540S Manual

25 Juli 2025

TP-Link VIGI C345 Manual

25 Juli 2025

TP-Link VIGI C485 Manual

25 Juli 2025

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

1 August 2025

31 Juli 2025

31 Juli 2025

31 Juli 2025

FLIR ioi HD CB-5222 Manual

30 Juli 2025

Eufy Cam S3 Pro Manual

30 Juli 2025

Telycam Vision+ 4KN 30X Manual

30 Juli 2025

Marshall Electronics CV630-BI Manual

30 Juli 2025

Telycam Vision+ SE Manual

30 Juli 2025

FLIR Ariel CC-3405 Manual

29 Juli 2025