TP-Link VIGI C230I Mini Manual

TP-Link Overvågningskamera VIGI C230I Mini

Læs gratis den danske manual til TP-Link VIGI C230I Mini (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om TP-Link VIGI C230I Mini, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Quick Start Guide
*Images may dier from actual products.
Appearance
Power Supply Interface
(12V DC)
RJ45 Ethernet Port
(supports PoE)
Micro SD Slot
Side Screws
Speaker
Package Contents
Network Camera Mounting Bracket
Quick Start Guide
Anchors and Screws
Quick
Start
Guide
•
Make sure your power supply matches your camera.
The camera’s standard power supply is 12V DC or
PoE (802.3af/at). The power source should meet LPS,
PS2, and other requirements according to IEC
62368-1.
• Make sure that the wall is strong enough to
withstand 4 times the weight of the camera and
mounting bracket.
• If you are uncertain or uncomfortable performing the
installation, consult a qualied electrician.
Safety First:
Mounting Template
2. Decide how to route the cable through the ceiling/wall. 4. Loosen the lens screw, rotate the lens base to adjust the
angle of the lens as desired, and then tighten the lens screw.
Tighten the side screws to secure the cover.
3. Loosen the three screws on the side of the camera to
remove the cover. Push the camera upwards and rotate
the camera clockwise to snap it into the mounting bracket.
1. Stick the mounting template to the desired mounting place.
Drill 3 screw holes according to the template, then install the
mounting bracket.
3MP Mini Dome Network Camera
Reset Button
Microphone
Mounting Template
Mounting Bracket
Point one of the arrows on the
mounting template in the direction
of the lens and stick it to the
ceiling/wall.
Lens Base
Dome
Anchor
Self-tapping Screw
Install mounting bracket
Reinstall the coverAdjust lens angle
Snap the camera into
the bracket
Press for 5 seconds to reset the
camera to factory settings.
Note: You can also slightly adjust the direction of the dome, but make sure that the
arrow symbol on the dome does not exceed the notch on the lens base.
Remove the cover
Ceiling or Wall
Route the cable through the
round hole in the middle of
the upper mounting bracket
Knock out the cable hole on the
side and route the cable from
the side
Lens Screw
Loosen to remove the cover.
More Management Methods
1. Download the on your VIGI Security Manager
computer at
https://www.tp-link.com/support/download/vigi-s
ecurity-manager/.
2. Install the and open it. VIGI Security Manager
3. Cameras on the same network as your computer
can be automatically discovered. Go to Settings >
Discovered Devices + Add, click to activate your
discovered cameras by setting passwords, and
follow the instructions to add your cameras.
Method 1: Via the VIGI Security Manager
(Windows only)
You can also access and manage your cameras via any of the methods below.
View live video and modify camera settings on
your computer.
Method 3: Via a Web Browser
View live video and modify camera settings via a
web browser.
1. Find the camera's IP address on your router’s client
page.
2. On your local computer, open a web browser and enter
https://camera's IP address (https://192.168.0.60 by
default).
3. Select your Country/Region and Time Zone.
4. Set a password to activate the camera.
Done. You can view the live video on the Preview page, and
go to the Settings page to change camera settings.
Method 2: Via the TP-Link VIGI App
Remotely view live video, manage cameras, and
get instant alerts.
2
Use Your Camera with an NVR
VIGI NVR
Monitor
Network Device
(e.g., Switch or Router)
The camera works with an NVR for easier batch access and management.
*Here we use a VIGI NVR as an example.
Frequently Asked Questions (FAQ)
Q1: What can I do if no cameras are discovered?
• Refresh to discover your camera again.
• Make sure the camera is powered on.
• Make sure your camera and NVR/computer are in the same subnet. If not,
use the VIGI Security Manager to set camera’s network parameters.
• Try to add your cameras manually.
• For other NVR brands, make sure you have activated the camera by setting
a password via the or app. VIGI Security Manager TP-Link VIGI
Q2: How do I know the camera is powered on?
• The IR LED will turn on for about 10 seconds once the camera is powered on. If
it’s o, you can cover the lens for several seconds and check if the IR LED turns
on.
• Check the LED status of the network device your camera is connected to.
For more questions, please refer to
https://www.tp-link.com/support/faq/2850/
• Do not use any other chargers than those recommended.
• Do not use damaged charger or USB cable to charge the device.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Adapter shall be installed near the equipment and shall be easily accessible.
• Keep the device away from water, fire, humidity or hot environments.
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant
provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant
provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety)
Regulations 2016.
The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca/
Network Camera
Network Camera
Step 2. Power On the Cameras
Power on your cameras with the PoE power supply
or an external power supply.
Step 1. Connect the Hardware
Connect your cameras to the same network as your
NVR (as shown above).
Step 3. Add Cameras with the NVR
Before you start, make sure the NVR is working properly.
1. Right click on the Live View screen and click Add
Camera.
2. Select your camera and click + to add your camera
directly. If you have disabled Plug and Play on your
NVR, create a password or use a preset password
for your camera.
Note: If you can’t nd your camera, refer to FAQ-Q1.
Done! You can now view live video and manage cameras.
Using your cameras with other NVR brands:
Step 1: Power on your cameras and connect them to the network.
Step 2: Activate the camera using the or app (refer to the next section).VIGI Security Manager TP-Link VIGI
Step 3: Refer to the NVR’s User Manual to add cameras.
1. Download and install the app.TP-Link VIGI
2. Open the app and log in with your TP-Link VIGI
TP-Link ID. If you don’t have an account, sign up rst.
3. Tap the button on the top right and follow the app +
instructions to activate and add your cameras.
or
For technical support, replacement services, user guides, and more
information, please visit https://www.tp-link.com/support, or simply
scan the QR code.

Produkt Specifikationer

Mærke: TP-Link
Kategori: Overvågningskamera
Model: VIGI C230I Mini

Har du brug for hjælp?

Hvis du har brug for hjælp til TP-Link VIGI C230I Mini stil et spørgsmål nedenfor, og andre brugere vil svare dig


Overvågningskamera TP-Link Manualer

TP-Link

TP-Link VIGI S385PI Manual

12 August 2025
TP-Link

TP-Link Tapo TC42 Manual

12 August 2025
TP-Link

TP-Link VIGI C355 Manual

26 Juli 2025
TP-Link

TP-Link Tapo D130 Manual

26 Juli 2025
TP-Link

TP-Link Tapo C125 Manual

25 Juli 2025
TP-Link

TP-Link Tapo C720 Manual

25 Juli 2025
TP-Link

TP-Link INSIGHT S345-4G Manual

25 Juli 2025
TP-Link

TP-Link VIGI C385 Manual

25 Juli 2025
TP-Link

TP-Link VIGI C445 Manual

25 Juli 2025
TP-Link

TP-Link VIGI C540S Manual

25 Juli 2025

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Swann

Swann SONVK-1676808 Manual

13 August 2025
Swann

Swann SONVK-876806 Manual

13 August 2025
Swann

Swann SWNVW-MR4KCAM Manual

13 August 2025
Swann

Swann SWDVK-845808WL Manual

13 August 2025
Swann

Swann SWDVK-84880W6AOC Manual

13 August 2025
Swann

Swann SONVK-1676808B8D Manual

13 August 2025
Swann

Swann SWDVK-84880W8AOC Manual

13 August 2025
Swann

Swann SWNVK-88680W4FB Manual

13 August 2025
Swann

Swann SONVK-16898081PT Manual

13 August 2025
Swann

Swann SWDVK-846804MQB Manual

13 August 2025