Tripp Lite APSRM4 Manual

Tripp Lite Joystick APSRM4

Læs gratis den danske manual til Tripp Lite APSRM4 (8 sider) i kategorien Joystick. Denne vejledning er vurderet som hjælpsom af 45 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 23 anmeldelser. Har du et spørgsmål om Tripp Lite APSRM4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Connecting to an Inverter or Inverter/Charger

Connect one end of the included RJ-type cable into the RJ45 Remote Port on the front of your

PowerVerter Inverter or Inverter/Charger. Connect the other end into either of the two RJ45

Remote Ports on the bottom of the Remote Control Module.

Connecting to Additional Remote Control Modules (Optional)

You can control a single PowerVerter Inverter or Inverter/Charger with two separate Remote

Control Modules. Connect one Remote Control Module directly to the PowerVerter as described

above. Connect either of the two RJ45 Remote Ports on the bottom of the second Remote

Control Module directly to the remaining RJ45 Remote Port on the bottom of the first Remote

Control Module using an RJ-type cable, included.

Connecting to Vehicle's Ignition Switch (Optional)

You can set the Remote Control Module to automatically perform either one of two additional

control functions (DISABLE or ENABLE) by connecting the Remote Control Module to the

vehicle’s ignition switch. These connections are optional; the Remote Control Module will

function without these connections.

“DISABLE” Control Function: This function automatically disables (turns OFF) the AC

power output from the PowerVerter when the vehicle's ignition switch is placed in the

“Engine Run” position. This function will satisfy local codes and requirements concerning

video monitors (or TVs) that are located within a driver’s view by automatically turning

them off when the engine is started.

Using the interface cable* (included with select models), connect the black lead to vehicle

ground (battery negative). Connect the red lead to the “Engine Run” terminal of the

vehicle’s ignition switch. Then, connect the interface cable’s mini-plug to either of two

Ignition Switch Control Jacks located on the side panel of the Remote Control Module: if

you are controlling a PV Inverter, insert the mini-plug into the jack labeled “J-1”; if you are

controlling an APS, RV or EMS Inverter/Charger, insert the mini-plug into the jack labeled

“J-2”. After connecting the interface cable, set the Remote Control Module's switch to

either “ON” (for PV models) or “CHRG ONLY” (for APS, RV or EMS models).

* The interface cable (included with select models) has a mini-plug on one end and two wire leads (one black and one red) on the other.

“ENABLE” Control Function: This function automatically enables (turns ON) the AC

power output from the PowerVerter when the vehicle's ignition switch is placed in either the

“Accessory” or “Engine Run” positions. This function minimizes the risk of discharging the

vehicle battery when the vehicle is parked with the engine off for an extended period of

time.*

Using the interface cable** (included with select models), connect the black lead to vehicle

ground (battery negative). Connect the red lead to the “Accessory” terminal of the vehicle’s

ignition switch. Then, connect the interface cable’s mini-plug to either of two Ignition

Switch Control Jacks located on the side panel of the Remote Control Module: if you are

controlling a PV Inverter, insert the mini-plug into the jack labeled “J-2”; if you are

controlling an APS, RV or EMS Inverter/Charger, insert the mini-plug into the jack labeled

“J-1”. After connecting the interface cable, set the Remote Control Module’s switch to

either “ON” (for PV models) or “CHRG ONLY” (for APS, RV or EMS models).

* Note: a very small discharge current (approximately 18 milliamps) will still exist that should not affect starting ability, even if the

vehicle engine has not been turned on for several days. To reduce this current to zero, set the Remote Control Module’s switch to either

“OFF” (for PV models) or “AUTO” (for APS, RV or EMS models).** The interface cable (included with select models) has a mini-plug

on one end and two wire leads (one black and one red) on the other.

Mounting Without Included Mounting Plate (Optional)

Affix either one of the two included labels to the front panel of the Remote Control Module.

The labels identify the Module's LEDs. Choose the label marked "PV" if you are using the

Remote Control Module to operate a Tripp Lite Inverter. Choose the label market "APS" if

you are using the Remote Control Module to operate a Tripp Lite Inverter/Charger.

Mount the Remote Control Module in a variety of ways (under-counter, recessed, etc.)

using user-supplied hardware inserted through the Module's mounting holes/slots and into

the mounting surface.

Owner’s Manual

Installation

The Remote Control Module allows you to remotely monitor and control many of the functions of select* Tripp Lite PowerVerter PV Inverters and PowerVerter

APS, RV or EMS Inverter/Chargers.

* Only those models featuring an RJ45 Remote Port.

WARNING! THE IGNITION SWITCH CONTROL FUNCTION IS

ONLY FOR USE WITH 12V NEGATIVE GROUND SYSTEMS.

Wiring the Ignition Switch Control Cable to your vehicle’s ignition requires a

qualified technician, who must determine the proper wiring procedure.

1111 W. 35th Street Chicago, IL 60609 USA

Customer Support: (773) 869-1234 • www.tripplite.com

Operation

Mounting with Included Mounting Plate (Optional)

• For PVXXXXHF Model Inverters: Install with Inverter side of plate facing out.

• For PVXXXXFC Model Inverters: Install with Inverter side of plate facing out;

place included label on plate as shown.

• For Inverter/Chargers (All Models): Install with Inverter/Charger side of plate facing out.

STEP 1) Using the two included

machine screws, attach the

Mounting Plate to the front of the

Remote Control Module.

STEP 2) Using the four included

sheet metal screws, install the

Mounting Plate and Remote

Control Module in the panel

opening of your vehicle.

5.25 in. (13.335 cm.)

3.25 in

(8.255 cm.)

Choose operation based on whether you connect your Remote Control Module to an Inverter

(PV series) or Inverter/Charger (APS, RV or EMS series).

INVERTER (PV series)

OFF/ON Switch:

Move this switch to the “ON” position to have your Inverter provide connected equipment

with AC power by converting DC power from an attached battery.

To prevent battery drain, leave it in the “OFF” or “INV OFF”* position when not using

connected equipment.

“BATTERY” LEDs: These three lights show the approximate charge of your

connected batteries. See chart below for approximate charges.

LEDs Illuminated Approximate Charge

Green 96% - Full

Green & yellow 81% - 95%

Yellow 61% - 80%

Yellow & red 41% - 60%

Red 21% - 40%

All three lights off 1% - 20%

Flashing red 0% (Inverter shutdown)

All three lights flash slowly Excessive discharge

All three lights flash quickly Overcharge

* “OFF” when used with lable; “INV OFF” when used with mounting plate.

OFF

34 5

Module shown without mounting plate

WARRANTY

REGISTRATION:

chance to win a FREE Tripp Lite

product—www.tripplite.com/warranty

Remote Control Module & Mounting Plate

for use with select PowerVerter®Inverters (PV series) or PowerVerter

®Inverter/Chargers (APS, RV or EMS series)

LO W

M ED I UM

M ED I U M

HIG

Placement of Label

200603011--APSRM2 Owner’s Manual Update.qxd 3/24/2006 3:22 PM Page 1

Produkt Specifikationer

Mærke:	Tripp Lite
Kategori:	Joystick
Model:	APSRM4
Bredde:	101.6 mm
Dybde:	57.2 mm
Højde:	31.8 mm
Vægt:	180 g
Pakkevægt:	1000 g
Pakkedybde:	180.3 mm
Pakkebredde:	259.1 mm
Pakkehøjde:	61 mm
Dimensioner (BxDxH):	102 x 57 x 32 mm
Hovedkassen højde (udvendigt):	228.6 mm
Hovedkassens længde (udvendigt):	200.7 mm
Hovedkassens bruttovægt (udvendigt):	6120 g
Hovedkassens bredde (udvendigt):	304.8 mm
Oprindelsesland:	Kina
Produkter pr. hovedkasse (udvendigt):	6 stk
Hovedkasse (udvendig) GTIN (EAN/UPC):	10037332122350
AC udgange, antal:	0 AC stikkontakt(er)