Unitech MS340 Manual

Unitech Stregkodelæser MS340

Læs gratis den danske manual til Unitech MS340 (67 sider) i kategorien Stregkodelæser. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Unitech MS340, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/67

unitech is a registered trademark of unitech Electronics Co., Ltd

Long Range CCD Barcode Scanner

- MS340 -

User's Manual

Version 1.2

unitech is a registered trademark of unitech Electronics Co., Ltd

Revision History

Date Change Description Version

2015/10/5 first published version 1.0

2015/12/1 4.1.1 Interface Selection :

Delete WAND Emulation, Add Virtual COM

1.1

2016/1/8  Delete 4.2.4- WAND emulation

 Update 4.4 – Reading level



4.1.2 Reading Mode Selection--

Replace Auto sense to presentation

1.2

unitech is a registered trademark of unitech Electronics Co., Ltd.

1. This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

2. This device complies with FCC RF radiation exposure limits set forth for

an uncontrolled environment. To maintain compliance with FCC RF

exposure requirements, avoid direct contact to the transmitting antenna

during transmitting.

3. Any changes or modifications (including the antennas) made to this device

that are not expressly approved by the manufacturer may void the user’s

authority to operate the equipment.

Operation on the 5.15 - 5.25GHz frequency band is restricted to indoor use

only. The FCC requires indoor use for the 5.15-5.25GHz band to reduce the

potential for harmful interference to co-channel Mobile Satellite Systems.

Therefore, it will only transmit on the 5.25-5.35 GHz, 5.47-5.725 GHz and

5.725–5.850 GHz band when associated with an access point (AP).

FCC Label Statement

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference

that may cause undesired operation.

RF Radiation Exposure Statement

For body contact during operation, this device has been tested and meets FCC

RF exposure guidelines when used with an accessory that contains no metal

and that positions the handset a minimum of 1.5 cm from the body.

Use of other accessories may not ensure compliance with FCC RF exposure

guidelines.

Canadian Compliance Statement

This Class B Digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

Cet appareil numerique de la classe B respecte les exigences du Reglement

sur le material broilleur du Canada.

iii

unitech is a registered trademark of unitech Electronics Co., Ltd.

European Conformity Statement

unitech Electronics co., Ltd herewith declares that the unitech product is in

compliance with the essential requirements and all other provisions of the

R&TTE 1999/5/EC directive, the EMC 2004/108/EC directive and the Low

Voltage 2006/95/EC directive.

The declaration of conformity is available for download at :

https://portal.unitech.eu/public/Safetyregulatorystatement

RoHS Statement

This device conforms to RoHS (Restriction of

Hazardous Substances) European Union regulations

that set maximum concentration limits on hazardous

materials used in electrical and electronic

equipment.

Waste electrical and electronic equipment (WEEE)

unitech has set up a policy and process to meet the EU

directive 2002/96/EC and update 2003/108/EC

concerning electronic waste disposal.

For more detailed information of the electronic waste

disposal of the products you have purchased from

unitech directly or via unitech’s resellers, you shall either

contact your local supplier or visit us at :

https://portal.unitech.eu/public/WEEE

unitech is a registered trademark of unitech Electronics Co., Ltd.

Taiwan NCC Warning Statement

交通部電信總局低功率電波輻射性電機管理辦法

交通部電信總局低功率電波輻射性電機管理辦法交通部電信總局低功率電波輻射性電機管理辦法

第十二條：經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者

均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

第十四條：低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有

干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。

低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備

之干擾。

注意事項:

1. 使用過度恐傷害視力。

2. 使用30分鐘請休息10分鐘；2歲以下幼兒不看螢幕，2歲以上每天看螢幕不要超過

1小時。

unitech is a registered trademark of unitech Electronics Co., Ltd.

Laser Information

The unitech product is certified in the U.S. to conform to the requirements of

DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1.

Class II and Class 2 products are not considered to be hazardous. The unitech

product contains internally a Visible Laser Diode (VLD) whose emissions do

not exceed the maximum limits as set forth in the above regulations. The

scanner is designed so that there is no human access to harmful laser light

during normal operation, user maintenance or prescribed service operations.

The laser safety warning label required by the DHHS/IEC for the unitech

product’s optional laser scanner module is located on the memory

compartment cover, on the back of the unit.

* Laser information only applies to the products with laser components.

CAUTION! Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous laser

light. Use of optical instruments with the scanner, including

binoculars, microscopes, and magnifying glasses, with will

increase eye damage. This does not include eyeglasses worn by

the user.

LED Information

The unitech product contains LED indicator(s) or LED ring whose luminance is

not harmful to human eyes during normal operation, user maintenance or

prescribed service operations.

*LED information only applies to the products with LED components.

vii

unitech is a registered trademark of unitech Electronics Co., Ltd.

 RISK OF EXPLOSION IF BATTERY IS

REPLACED INCORRECTLY.

DISPOSE OF USED BATTERIES ACCORDING

TO THE INSTRUCTIONS..

 如果更換不正確之電池行事會有爆炸的風險

請依製造商說明書處理用過之電池

CAUTION!

 如果更换不正确之电池行事会有爆炸的风险

请依制造商说明书处理用过之电池

Battery charge notice

It is important to consider temperature when the battery pack is charging.

Charging is most efficient at normal room temperature or in a slightly cooler

environment. It is essential that batteries are charged within the stated range of

0°C to 40°C. Charging batteries outside of the specified range could damage

the batteries and shorten their life cycle.

CAUTION! Do not charge batteries at a temperature lower than 0°C. This will

and make the batteries unstable and dangerous. Please use a

battery temperature detecting device for a charger to ensure a

safe charging temperature range.

Storage and safety notice

Although charged batteries may be left unused for several months, their

capacity may be depleted due to build up of internal resistance. If this happens,

they will require recharging prior to use. Batteries may be stored at

temperatures between -20°C to 60°C, however they may deplete more rapidly

at higher temperatures. It is recommended to store batteries at room

temperature.

* The message above only applies to the usage of the removable batteries.

For the products with non-removable batteries / without batteries, please refer to

the specification of each product.

Product Operation and Storage Notice

The unitech product has applicable operation and storage temperature

conditions. Please follow the limitation of suggested temperature conditions to

avoid failure, damage or malfunction.

*For applicable temperature conditions, please refer to the specification of each

product.

viii

unitech is a registered trademark of unitech Electronics Co., Ltd.

Adapter Notice

1. Please do not leave the power adapter in the socket when it is not

connected to your unitech product for charging.

2. Please remove the power adapter when the battery is fully recharged.

3. The bundled power adapter that comes with your unitech product is not

meant to be used outdoors. An adapter exposed to water or rain, or a very

humid environment can cause damage to both the adapter and the

product.

4. Please only use the bundled power adapter or same specification of

adapter to charge your unitech product. Using the wrong power adapter

can damage your unitech product.

* The message above only applies to the product connected to the adapter.

For the products without using the adapters, please refer to the specification of

each product.

Hearing Damage Warning

Zx.3 Warning

The warning shall be placed on the equipment, or on the packaging, or in the instruction manual and shall consist of

the following:

- the symbol of Figure 1 with a minimum height of 5 mm; and

- the following wording, or similar :

To prevent possible hearing damage, do not listen at high volume levels for long periods.

Alternatively, the entire warning may be given through the equipment display during use, when the user is asked to

acknowledge activation of the higher level.

unitech is a registered trademark of unitech Electronics Co., Ltd.

Worldwide Support

unitech’s professional support team is available to quickly answer questions or

assist with technical-related issues. Should an equipment problem occur,

please contact the nearest unitech regional service representative.

For complete contact information please visit the Web sites listed below:

Taipei, Taiwan – Headquarters Europe

Tel: +886-2-89121122 Tel: +31-13-4609292

E-mail: info@hq.ute.com E-mail: info@eu.ute.com

Address: 5F, No. 136, Lane 235, Baoqiao Road, Xindian

District, New Taipei City 231, Taiwan (R.O.C.)

Website: http://www.ute.com

Address:

Website:

Kapitein Hatterasstraat 19, 5015 BB,

Tilburg, the Netherlands

http://eu.ute.com

China Japan

Tel: +86-59-2310-9966 Tel: +81-3-35232766

E-mail: info@cn.ute.com E-mail: info@jp.ute.com

Address:

Website:

Room401C, 4F, RIHUA International Mansion,

Xinfeng 3nd Road, Huoju Hi-tech District,

Xiamen, Fujan , China

http://cn.ute.com

Address:

Website:

Kayabacho Nagaoka Building 8F.,1-5-19

Shinkawa, Chuo-Ku,

Tokyo, 104-0033, Japan

http://jp.ute.com

Asia & Pacific / Middle East Latin America

Tel: +886-2-27911556 Tel: +52-55-5171-0528

E-mail: info@apac.ute.com

info@india.ute.com

info@mideast.ute.com

E-mail:

Address:

info@latin.ute.com

17171 Park Row, Suite 210

Houston, TX 77084USA (Rep.)

Address: 4F., No. 236, ShinHu 2nd Rd.,

NeiHu Chiu, 114, Taipei,Taiwan

Website: http://latin.ute.com

Website: http://apac.ute.com / http://mideast.ute.com

North America

Tel: +1-714-8916400

E-mail:

Address:

Website:

info@us.ute.com / info@can.ute.com

6182 Katella Ave, Cypress, CA 90630, USA

http://us.ute.com / http://can.ute.com

unitech is a registered trademark of unitech Electronics Co., Ltd.

Table of Contents

Preface...........................................................................................................i

About This Manual ........................................................................................ i

Regulatory Compliance Statements .............................................................. i

Laser Information ......................................................................................... v

LED Information ........................................................................................... v

Battery Notice.............................................................................................. vi

Adapter Notice............................................................................................viii

Hearing Damage Warning ..........................................................................viii

Worldwide Support ...................................................................................... ix

Warranty Policy ............................................................................................ x

Chapter 1 - Overview................................................................................1

1.1 Package .................................................................................................1

1.2 Scanner Detail........................................................................................ 2

1.3 Specifications .........................................................................................3

1.4 Getting Started .......................................................................................5

1.5 Pin Assignment.......................................................................................6

1.6 LED Indicator / Beeper Sequence ..........................................................7

Chapter 2 – Configuration-General ......................................................8

2.1 Flow Chart..............................................................................................8

2.2 Loop of Programming.............................................................................9

2.3 Factory Default Settings .........................................................................9

2.4 Main Page of Configuration..................................................................10

Chapter 3 –Bar Codes & Others.......................................................... 11

3.1 SymboIogies Selection......................................................................... 11

3.2 UPC/EAN/JAN Parameters .................................................................. 13

3.3 Code 39 Parameters ............................................................................15

3.4 Code 128 Parameters ..........................................................................16

3.5 Interleave 25 Parameters ..................................................................... 17

3.6 Industrial 25 Parameters ......................................................................18

3.7 Matrix 25 Parameters ...........................................................................19

3.8 CODABAR/NW7 Parameters ............................................................... 20

3.9 Code 93 Parameters ............................................................................22

3.10 Code 11 Parameters...........................................................................23

xii

unitech is a registered trademark of unitech Electronics Co., Ltd.

3.11 MSI/PLESSEY Code Parameters.......................................................24

3.12 Code 2 of 6 Parameters .....................................................................25

3.13 LCD25 Parameters.............................................................................26

3.14 Telepen Parameters ...........................................................................27

3.15 GS1 Databar ......................................................................................28

3.16 Bar Code ID........................................................................................29

Chapter 4 – Command Setting.............................................................32

4.1 Interface & Reading Mode Selection ....................................................32

4.2 Communication Parameters.................................................................33

4.3 Language Selection..............................................................................37

4.4 Reading Level ......................................................................................38

4.5 Accuracy...............................................................................................39

4.6 Buzzer Beep Tone ................................................................................39

4.7 Sensitivity of Continuous Reading Mode..............................................40

4.8 Reverse Output Characters ..................................................................41

4.9 Setup Deletion......................................................................................41

4.10 Setup Insertion ...................................................................................44

Appendix A –Numeric Bar Codes........................................................47

Appendix B –ASCII Table.......................................................................48

Appendix C –Function Key Table........................................................52

Appendix D–Numeric Bar Codes2.......................................................53

unitech is a registered trademark of unitech Electronics Co.,Ltd

Chapter 1 - Overview

1.1 Package

Please make sure the following contents are in the MS340 gift box.

If something is missing or damaged, please contact your unitech

representative.

The standard package contents:

 MS340 Scanner

 Quick Start Guide

 Regulatory Compliance Statements

 Cable

Optional accessory:

 Hand-Free Stand

unitech is a registered trademark of unitech Electronics Co.,Ltd

1.2 Scanner Detail

Pin-hole

Scan Window

Trigger

Cable connector

LED indicator

unitech is a registered trademark of unitech Electronics Co.,Ltd

1.3 Specifications

Optical & Performance

Sensor Linear Imager

Visual Indicators Beep and LED (Good read Green)

System Interface USB, RS232, Keyboard Wedge

Light Source 635 nm Visible Red LED

Max. Resolution 4mil (0.1mm) PCS90%, Code39

Scan Rate Up to 500 scans/second

Skew Angle ±60° (±5°)

Pitch Angle ±10°~65° (±5°)

Printing Contrast Scale minimum 30%

Decoding Supports most standard 1D bar code, GS1 Databar

linear and stacked Codes

Depth of Field

(DOF Code39

PCS=90% )

unitech is a registered trademark of unitech Electronics Co.,Ltd

1.5 Pin Assignment

A. Input Port for Mini Decoder

DB 9 Male

B. Output Port

1. PC Keyboard Output

DIN 5 Male DIN 5 Female MiniDIN 6 Male MiniDIN 6 Female

2. RS232 Output

DB 9 Female

unitech is a registered trademark of unitech Electronics Co.,Ltd

1.6 LED Indicator / Beeper Sequence

DivisionAction/Status

LEDforBarcode

reading &

Communication

LEDforBattery

statusBeep / Sound

USB connection Green Light blinks Six Beeps

Data sent to PC

successfully Green Light blinks once One Beep

Barcode reading

Fail sent data to PC No action No action

unitech is a registered trademark of unitech Electronics Co.,Ltd

Chapter 2 – Configuration-General

2.1 Flow Chart

*Please scan the following barcodes for configuration

Start Configuration

End Configuration

Abort Configuration

Save Parameters

unitech is a registered trademark of unitech Electronics Co.,Ltd

2.4 Main Page of Configuration

Save Parameters

Recall Stored Parameters

Set All Defaults

Start Configuration

End Configuration

Abort Configuration

Version Information

Save Parameters -The parameter settings will be saved permanently.

Recall Stored Parameters - Replace the current parameters by the

parameters you saved last time.

Set AII Defaults - Set all the parameters to the factory default settings.

Abort Configuration - Terminate current programming status.

Version Information - Display the decoder version information and date code.

unitech is a registered trademark of unitech Electronics Co.,Ltd

3.2 UPC/EAN/JAN Parameters

A. Reading Type B. Supplemental Set Up

UPCA=EAN13 ON

UPCA=EAN13 OFF *

Not Transmit *

ISBN-10 Enable

ISBN-13 Enable *

Transmit 2 Code

ISSN Enable

ISSN Disable * Transmit 5 Code

Decode with

Supplement

Auto discriminate

Supplement *

Transmit 2&5 Code

Expand UPC-E

Enable

Expand UPC-E Disable *

EAN8=EAN13

Enable

EAN8=EAN13 Disable *

GTIN Format

Enable

GTIN Format

Disable *

unitech is a registered trademark of unitech Electronics Co.,Ltd

C. Check Digit Transmission

UPC-A Check Digit Transmission ON *

UPC-A Check Digit Transmission OFF

UPC-E Check Digit Transmission ON *

UPC-E Check Digit Transmission OFF

EAN-8 Check DigitTransmission ON *

EAN-8 Check DigitTransmission OFF

EAN-13 Check Digit Transmission ON *

EAN-13 Check Digit Transmission OFF

ISSN Check Digit Transmission ON *

ISSN Check Digit Transmission OFF

unitech is a registered trademark of unitech Electronics Co.,Ltd

2. Numeric Bar

Codes (Appendix A)

3.4 Code 128 Parameters

A. Reading Type B. Check Digit

Transmission

C. Append FNC2

UCC/EAN-128 Disable * UCC/EAN-128 Enable

Calculate Check

Digit& Not Transmit *

OFF*

Enable ‘]C1‘Code

Format *

Disable ‘]C1‘Code

Format

Calculate Check Digit

& Transmit

Enable Code128

Group Separators(GS) *

Disable Code128

Group Separators(GS)

Do Not Calculate

Check Digit

D. Set Up Code Length

To set the fixed length:

1. Scan the “Begin“ label of the desired set.

2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read.

3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.

Variable *

Fix Length (2 Sets Available)

1. 1st Set Begin 3. 1

st Set Complete

1. 2nd Set Begin 3. 2

nd Set Complete

Minimum Length

1. Begin 3. Complete

2. Numeric Bar

Codes (Appendix A)

2. Numeric Bar

Codes (Appendix A)

Produkt Specifikationer

Mærke:	Unitech
Kategori:	Stregkodelæser
Model:	MS340
Kode for international beskyttelse (IP):	IP42
Type:	Håndholdt stregkodelæser
Bredde:	72 mm
Dybde:	70 mm
Højde:	164 mm
Vægt:	173.5 g
Produktfarve:	Sort
Opbevaringstemperatur (T-T):	-20 - 70 °C
Relativ luftfugtighed ved drift (H-H):	20 - 95 %
Driftstemperatur (T-T):	0 - 50 °C
Scanner type:	1D
Beskyttelsesfunktioner:	Stødsikker
Kabler inkluderet:	USB
Forbindelsesteknologi:	Ledningsført
Certificering:	CE, FCC, BSMI, VCCI
LED-indikatorer:	Ja
Harmoniseret systemkode (HS):	84716070
Indgangsspænding:	5 V
Sensortype:	CCD
Standard grænseflader:	USB
Bølgelængde:	635 nm
Strømforbrug:	150 mA
Indbygget processer:	Ja
Læsehastighed (maks.):	500 læs/sek.
Tilt læsningsvinkel:	-60 - 60 °
Pitch læsningsvinkel:	-10 - 65 °
Understøtter lineær (1D) stregkoder:	Codabar, Code 11, Code 128, Code 128A, Code 128B, Code 128C, Code 39, Code 93, EAN 2, EAN 5, EAN-13, EAN-8, GS1-128 (UCC/EAN-128), JAN, MSI, Plessey, Telepen, U.P.C.
Understøtter matrix (2D) stregkoder:	Ikke understøttet
Arbejdsafstand:	400 mm
Lysniveauer (direkte sollys):	0 - 100000 Lux
PC-tilslutning:	USB 2.0