V-TAC VT-554 Manual


Læs gratis den danske manual til V-TAC VT-554 (27 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 10 anmeldelser. Har du et spørgsmål om V-TAC VT-554, eller vil du spørge andre brugere om produktet?

Side 1/27
WARNING!
1. Please make sure to turn off the power before starting the installation.
2. The light source of this luminaire is not replaceable, when the light source reaches its
end of life the whole luminaire should be replaced.
2. Installation should only be done by a certified electrician.
WEEE Number: 80133970
INSTALLATION INSTRUCTION
NEON FLEX LIGHT
This marking indicates that this
product should not be disposed of
with other household wastes.
Caution, risk of electric
shock.
IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT: SUPPORT@V-TAC.EU
FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST DEALERS.
V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B
2
YEARS
WARRANTY
*
IP68
RATING
Note: IP68 LED Neon Flex can be installed up to 20 meters (max)
inside the water.
TECHNICAL DATA:
Model VT-554
Was 6.5
Lumens 260
BeamAngle 12
Body Type Silicone
CRI >80
PCB Width 8mm
Roll 10
LED QTY/M 126
Current Power/M 0.27A
Opera on Temperature -20 to +60°c
Input Power DC: 24V
INTRODUCTION
Attention
!
>60°
vertically bending
Cutting instruction
Please cut only on the dotted/scissor marking on the LED Neon Flex.
No End Cap required.
SAFETY INSTRUCTION AND WARNINGS!
1. Please cut the LED Neon Flex according to the cutting as shown in the cutting instruc-
tions. Cutting outside the marking will damage the product. Please cut only on the
dotted/scissor marking on the LED Neon Flex. No End Cap required.
2. LED Neon Flex cannot be folded, bent or twisted during the installation. Please install
in straight direction. DO NOT turn on power until LED Neon Flex is connected properly
and well-installed.
3. DO NOT touch/cut the LED Neon Flex when power is on.
4. DO NOT power the LED Neon Flex in roll/package.
5. DO NOT install in flammable environment, and make sure well ventilated.
6. DO NOT wrap or cover LED Strip Light with any objects. Additional waterproof measure
needed when used outdoors.
7. DO NOT directly connect LED Neon to AC power. Special power plug is needed.
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best.
Please read these instructions carefully before starting the installing and keep this
manual handy for future reference. If you have any another query, please contact
our dealer or local vendor from whom you have purchased the product. They are
trained and ready to serve you at the best. The warranty is valid for 2 years from
the date of purchase. The warranty does not apply to damage caused by incorrect
installation or abnormal wear and tear. The company gives no warranty against
damage to any surface due to incorrect removal and installation of the product.
The products are suitable for 10-12 Hours Daily operation. Usage of product for 24
Hours a day would void the warranty. This product is warranted for manufacturing
defects only.


Produkt Specifikationer

Mærke: V-TAC
Kategori: Ikke kategoriseret
Model: VT-554

Har du brug for hjælp?

Hvis du har brug for hjælp til V-TAC VT-554 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret V-TAC Manualer

V-TAC

V-TAC VT-8310 Manual

7 Juni 2025
V-TAC

V-TAC VT-8-20 Manual

10 Marts 2025
V-TAC

V-TAC VT-61037 Manual

4 Marts 2025
V-TAC

V-TAC VT-22001 Manual

4 Marts 2025
V-TAC

V-TAC VT-11449 Manual

4 Marts 2025
V-TAC

V-TAC VT-44034 Manual

10 Januar 2025
V-TAC

V-TAC VT-44055 Manual

10 Januar 2025
V-TAC

V-TAC VT-4924 Manual

10 Januar 2025
V-TAC

V-TAC VT-12040-1 Manual

7 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer