Vaddio RoboTRAK Manual

Vaddio Overvågningskamera RoboTRAK

Læs gratis den danske manual til Vaddio RoboTRAK (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 21 anmeldelser. Har du et spørgsmål om Vaddio RoboTRAK, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Drop-Down Mount Accessory for RoboTRAK™

UNPACKING:

Carefully remove the product and all of the parts from the

packaging. Unpack and identify the following parts (cameras not

included):

➊

One (1) 1-14 Hex Nut (jamb nut)1.5” across by .375” Tall

➋

One (1) Offset Pipe with 1-14 Threads

➌

One (1) Mounting Flange (5” diameter)

➍

One (1) Tile Support Brace

➎

One (1) Large 5” Washer

➏

Two (2) 1-14 Hex Nut, 1.5” across x .547” Tall (one used as

fastener and the other as a top jamb nut)

(Cameras are not included)

Step 1: For suspended ceiling installations, mark a position in the center of

a ceiling tile where the ceiling mount is to be placed. The hole must be

positioned at the center of the ceiling tile lengthwise for 2’ x 4’ ceiling tiles to

line up with the tile support brace. Use the tile support brace as a template.

The tile support brace is meant to span the tile and distribute the weight into

the grid.

For drywall ceiling installations, mark a position in the ceiling while making

sure that there are no obstructions (structural supports, electrical, etc.) in the

area above the mount.

Step 2: Drill or cut a 1” (25.4mm) diameter hole in the tile or drywall at the

point where you marked the hole. For suspended ceiling installations, place

the support brace on the top of the ceiling tile and align the hole with the tile

support brace. There are six holes drilled in the support brace for attaching

to the building structure where regional codes require this additional support.

For drywall ceiling installations, place the Mounting Flange over the 1” hole,

and mark the four locations in the flange to install appropriate hardware (wall

anchors) for mounting the flange to the ceiling.

Step 3: Thread the 1.5” x .375” Jam Nut onto the bottom of the pipe (the side with the shorter threads), then thread the

Camera Platform all the way onto the pipe. Back the Camera Platform off the pipe (one rotation or less) until the back of the

Camera Platform aligns with the cable pass-thru. Carefully tighten the 1.5” x .375” Jam Nut down onto the threaded nut of the

Camera Platform.

Step 4: Thread the painted 5” flange onto the other end of the pipe.

Step 5: For suspended ceiling installations, slide the pipe with 5” flange end through the hole in the ceiling tile. From one tile

over, place the 5” washer onto the threaded pipe, and screw the first 1.5” x 5.5” hex nut onto the pipe thread and tighten the

hex nut down, then thread the second hex nut (jam nut) onto the top of the pipe and tighten it. Carefully feed the Cat-5 cabling

through the pipe and the cable pass-thru at the back of the camera mount. There are six (6) mounting points on the Tile

Support Brace to allow the integrator to tie the assembly to the structure for safety in seismic prone areas.

For drywall ceiling installations, once the appropriate mounting hardware for the flange is installed, carefully pull the Cat-5

cabling through the 1” hole in your drywall ceiling. Thread the cabling through the pipe, and pull it through the cable pass thru

at the back of the camera platform. Place the flange on the ceiling and tighten the screws down onto the mounting hardware.

Step 6: Place your camera onto the mount and secure it to the camera platform using the supplied black screw(s). Connect

the Cat. 5 cabling to the back of the camera and carefully feed excess Cat. 5 cabling back into the ceiling. Use the ¼” - 20

x .375: screws for the RoboSHOT cameras.

Installation and User Guide

➊

➏

➎

➍

➌

➋

Produkt Specifikationer

Mærke:	Vaddio
Kategori:	Overvågningskamera
Model:	RoboTRAK

Har du brug for hjælp?

Hvis du har brug for hjælp til Vaddio RoboTRAK stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Vaddio Manualer

Vaddio EasyIP 5 ePTZ Manual

10 Oktober 2025

Vaddio ZoomSHOT 20 SE AVBMP Manual

9 Oktober 2025

Vaddio EasyIP 30 Manual

27 August 2025

Vaddio EasyIP 20 Manual

5 Juli 2025

Vaddio RoboFLIP 30 HDBT Manual

12 August 2024

Vaddio RoboTRAK Manual

3 August 2024

Vaddio Thin Profile Wall Mount Bracket Manual

4 Marts 2023

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

AVer HUB35-EXT35 Manual

11 December 2025

11 December 2025

11 December 2025

10 December 2025

10 December 2025

4XEM 4X-FD7132 Manual

10 December 2025

Telycam Vision+ N3 Manual

7 December 2025

FLIR FC-690 AI Manual

5 December 2025

FLIR FH-625 R Manual

5 December 2025

FLIR FC-644 AI-R Manual

5 December 2025