Valcom VBB-1424 Manual

Valcom Accu VBB-1424

Læs gratis den danske manual til Valcom VBB-1424 (3 sider) i kategorien Accu. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Valcom VBB-1424, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

VSP VP- - -6124 UPS

Issue 3

1947271

VP- -6124 UPS

ADD ON OPTION FOR THE VP- - -6124/VP 6124 E

POWER SUPPLY

INTRODUCTION

The VP- -6124 UPS is an optional unit that allows the

VP- - -6124/VP 6124 E to supply power during a power

outage.

The VP- - - -6124 UPS is comprised of a VP 6124 UPS

(Charger) and a VBB-1424 (Battery Enclosure). The

VP- - -6124 UPS connects to the VP 6124 Power Supply

(To receive power to charge the batteries).

Listed below are specifications and recommendations

for power sources as well as precautionary

instructions.

UPS Float Standby Charging

Charging Voltage: 27.6 Volts (13.8 Volts per battery)

Current Limit: 900mA charging

100mA at 27 Volts final charge

Fusing: 1 Amp auto-reset polyswitch

6 Amps accidental reverse battery polyswitch

Time Required to Recharge Battery

7AH Battery: 14 hours

Length of Time Battery Will Provide

Power

• With four 7AH 12V batteries for 14AH total

3 Amps load draw: 3 hours run time

6 Amps full load: 1.5 hours run time

Use of batteries greater than 7AH is not

recommended since 90% of all power outages are less

than an hour in length and the time to evacuate a

building is less than an hour.

NOTE: To insure trouble- -free UPS back up

operation, five years batteries must be replaced five

years from the date of manufacturing.

DIMENSIONS/WEIGHT

• 10.30"H x 3.50"W x 2.25"D

• (26.16cm H x 8.89cm W x 5.72cm D)

2.90 lbs. (1.32 kg)

INSTALLATION

The VP- -6124 UPS (Charger) is designed for wall

mounting only. Screw the mounting plate to the wall

near the VP- - -6124/VP 6124 E and position the

VP- -6124 UPS onto the mounting plate.

Attach the UPS unit securely to the bracket lip using

the 6- -32 x 3/8" long Phillips head self tapping screw

supplied. Place the VBB-1424 on the floor within six

feet of the unit.

CONNECTIONS

• Disconnect AC power from the power supply.

• Remove plug button from the VP- - -6124/VP 6124 E.

• Remove wire access cover from the

VP- - -6124/VP 6124 E.

• Using the cable designated by the tag labeled

Valcom P/N WA-784 with four positions

connector and attached to VP- -6124 UPS

(Charger), place the Molex connector through the

hole on the power supply and connect the

charger to the Molex input connector on the

VP-6124 Power Supply.

• Snap strain relief into place.

• Replace wire access cover on the

VP- - -6124/VP 6124 E.

• Remove cover from Battery Backup.

• Push cable labeled Valcom P/N WA-783 with two

positions connector through the hole on the

battery enclosure and snap strain relief into

place.

Produkt Specifikationer

Mærke:	Valcom
Kategori:	Accu
Model:	VBB-1424
Vægt:	- g
Produktfarve:	Grå
Batterispænding:	24 V
Batterikapacitet:	- mAh
Batteriteknologi:	Blybatterier (VRLA)
Relativ luftfugtighed ved drift (H-H):	10 - 90 %
Driftstemperatur (T-T):	0 - 50 °C
Strømforsyningstype:	DC
Indgangsspænding:	105 - 120 V
Numre af batterier medfølger:	1 stk
Intern:	Ingen
Kompatible produkter:	VP-6124-UPS
Kapabilitet:	VP-6124-UPS
Spænding:	24 V