Vango Velocity 300 Manual

Vango Telt Velocity 300

Læs gratis den danske manual til Vango Velocity 300 (1 sider) i kategorien Telt. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Vango Velocity 300, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

IF YOU HAVE ANY PROBLEMS PLEASE CONTACT YOUR LOCAL RETAILER or

AMG Group Ltd., Kelburn Business Park, Port Glasgow, Scotland. PA14 6TD.

UK Consumer Hotline: 0844 811 0535 E-Mail: info@vango.co.uk

Calls to our Customer Hotline cost 5p per minute. Calls from mobile phones, cable networks or public payphones will generally cost more.

INNER ATTACHMENT

• Open out inner tents inside ysheet and position

doorway to correspond with the living area.

• Starting from the rear corners of the tent, attach the

hooks on the inner groundsheet to

corresponding rings on the tent groundsheet.

• Suspend the inner by attaching toggles of inner tent

through rings on inside of ysheet. Do the rear rst

and work forward.

TENSION BAND SYSTEM

• When required, remove Tension Band System from

pockets and clip into the buckles in the ceiling of the

tent.

• Adjust the straps until they are taut but do not over-

tension.

TO DEFLATE THE AIRBEAM TENT

• Unscrew the valve fully from the beam, taking care as the

valve will be under pressure from the air inside the tube.

IN THE UNLIKELY EVENT OF A PUNCTURE

• Note: Most apparent punctures are a result of the valve

not being screwed in correctly. Please check valves

before changing AirBeam tube.

• eate the AirBeam. Unzip the internal ysheet sleeve D

which contains the aected beam.

• Remove the tube and its protective outer.

• The zips for the protective outer are cable tied together

to prevent accidental access. Cut the cable tie and open

the zip. DO NOT open these zips when tube is inated.

• Remove the clear rubberised tube from the protective

sleeve taking care when removing the valve from the

sleeve.

• Partially inate the tube and pass through a bucket or

basin of water, looking for air bubbles. This will indicate

location of puncture.

• Use the repair patch provided and cover hole, using

instructions on patch. Re-insert tube into protective

outer, closing zip from both ends, so that zip pullers are

in the centre of the sleeve, and then replace into the

ysheet sleeve. (This may be easier with the tube

partially inated)

FLYSHEET FIRST PITCHING/COMBINED PITCHING

• Unpack and position the tent in the required direction.

• Peg out the 4 corners using the pegs supplied.

• Locate inating points at the base of each beam.

• Access the beams through the zipped entry points and

through the side door.

• For the rst use of the tent, fully unscrew all valves from

the AirBeams and screw back in carefully - this ensures

that the valve is not cross-threaded.

• Remove smaller screw-cap on valve and insert largest

pump nozzle of the Vango AirBeam™ pump supplied.

• Inate all tubes to 7psi. The tubes MUST be guided into

an arch as they are inated.

• Final tube pressure MUST NOT exceed 8psi.

DO NOT OVER-INFLATE THE BEAMS

• Start with the centre tube and guide the beam into an

upright position while it is inating.

• Inate the other beams.

• Remove pump and tighten screw-cap. Ensure both parts

of valve are well tted so it is air tight but do not over

tighten.

• Ensure the tent is in a straight line. The groundsheet

should be at and wrinkle free.

• Secure the tent by pegging out the sides using all the

pegging points available.

• Peg out ALL the guy lines, ensuring that they are in line

with the beam or seam they are attached to.

• Re-position and adjust tensioning where necessary.

CORRECT PUMP SETUP

Pump Body -> Pressure Valve -> Pressure Gauge -> Hose

(Ensure Valve/Gauge/Hose are connected to Ination

port of pump)

CORRECT AIRBEAM VALVE SETUP

Ination Deation

Velocity

Produkt Specifikationer

Mærke:	Vango
Kategori:	Telt
Model:	Velocity 300

Har du brug for hjælp?

Hvis du har brug for hjælp til Vango Velocity 300 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Telt Vango Manualer

Vango Gamma 200 Manual

13 September 2024

Vango Aether Air 600XL Manual

1 September 2024

Vango Avington Flow 500 Manual

1 September 2024

Vango Mokala 450 Manual

1 September 2024

Vango Harris 350 Manual

1 September 2024

Vango Anantara IV Air TC 450XL Manual

1 September 2024

Vango Lismore Air 600XL Manual

1 September 2024

Vango Aether Air 450XL Manual

1 September 2024

Vango Harris Air 350 Manual

1 September 2024

Vango Inspire 500 Manual

29 August 2024

Telt Manualer

Nyeste Telt Manualer

De Waard Zeester Manual

7 Oktober 2024

Eureka El Capitan 2 Manual

6 Oktober 2024

Eureka KeeGo 2 Manual

4 Oktober 2024

SereneLife SLTET30 Manual

1 Oktober 2024

Calima 46074 Manual

1 Oktober 2024

SereneLife SLPTLB106 Manual

1 Oktober 2024

SereneLife SLPTSR107 Manual

30 September 2024

Eureka KeeGo Solo Manual

30 September 2024

Vaude Badawi Long 6 Manual

29 September 2024

De Waard Stormmeeuw Manual

25 September 2024