Vantec EZ Swap M2500 Manual

Vantec Disk array EZ Swap M2500

Læs gratis den danske manual til Vantec EZ Swap M2500 (2 sider) i kategorien Disk array. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 20 anmeldelser. Har du et spørgsmål om Vantec EZ Swap M2500, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Key x2

Mounting Screws

x12

Key x2

Mounting Screws

Key x2

Mounting Screws

SATA/SAS Cable Power Cable

Verify the package contents

1. Remove all carrier trays

Install storage unit into an open 5.25”

drive bay and secure the unit using

the correct mounting screws shown

on both sides of the storage unit

3. 4.

Install HDDs/SSDs on to the carrier

trays using the 4 correct mounting

screws shown on the underside of

the tray

5. Carefully slide the tray with the mounted

hard drive into the storage bay, close the

securing arm and lock the tray

Connect power and SATA/SAS* data

cable on the back of the storage unit

*SATA drive HAVE to be connected to SATA controller

and SAS drives HAVE to be connected to SAS controller

Compruebe el contenido del paquete

Vericare i contenuti della confezione

Lieferumfang prüfen

Vériez le contenu de l'emballage

梱包内容を確認します

确认包装内容

Quite toda las bandejas portadoras

Rimuovere tutti i cassetti

Alle Trägereinsätze entfernen

Retirez tous les plateaux de support

キャリアトレーをすべて取り除きます

移除所有拖盘

Instale la unidad de almacenamiento en una bahía de

unidades de 5,25” y je la unidad utilizando los tornillos de

instalación correctos mostrados a ambos lados de la unidad

almacenamiento

Installare l’unità d’archiviazione in un alloggio unità 5,25” e

ssarla su entrambi i lati utilizzando le viti appropriate

Installieren Speichereinheit in einem oenen 5,25

Speichergerät in einem freien 5,25-Zoll-Laufwerkseinschub

installieren und das Gerät mit Hilfe der richtigen

Montageschrauben an beiden Seiten des Speichergerätes

befestigen

Installez l'unité de stockage dans un logement de lecteur

5,25" ouvert et xez l'appareil à l'aide des vis de montage

adéquates, comme indiqué sur les deux côtés de l'unité de

stockage

空いている5.25インチドライブベイにストレージユニッ

トを配置し、ユニットの両側に表示されている適切なマ

ウントねじを使用して固定します

将本装置安装至5.25”硬盘架上，并注意使用正确的螺丝

来固定此装置

Instale las unidades de disco duro y de estado sólido en las

bandejas portadoras utilizando 4 tornillos de instalación

correctos mostrados en la parte inferior de la bandeja

Installare le unità HDD/SSD nei cassetti utilizzando le 4 viti

appropriate come mostrato sulla parte inferiore del cassetto

HDDs/SSDs an den Trägereinsätzen installieren; dazu die 4

richtigen Montageschrauben an der Unterseite des Einsatzes

verwenden

Installez les disques durs / SSD sur les plateaux de support en

utilisant les vis de xation de 4 adéquates, comme indiqué

sur la face inférieure du plateau

キャリアトレーの下部に示されているとおりに、

HDD/SSDを4サイズの適切なマウントねじで設置します

将HSS/SSD安装到托盘上，并于拖盘下方使用4个螺丝固定

Deslice con cuidado la bandeja con la unidad de disco duro

montada en la bahía de almacenamiento, cierre el brazo de

seguridad y bloquee la bandeja

Fare scorrere delicatamente il cassetto con il disco rigido

installato nell’alloggio, chiudere il braccio di ssaggio e

bloccare il cassetto

Einsatz mit der montierten Festplatte vorsichtig in den

Speichereinschub schieben, Sicherungsarm schließen und

Einsatz verriegeln

Faites glisser délicatement le plateau avec le disque dur

monté dans le logement du lecteur, refermez le bras de

xation et verrouillez le plateau

ハードドライブをマウントしたトレーをゆっくりとスト

レージベイにスライドして入れ、固定アームを閉じてト

レーをロックします

小心的将锁上硬碟的拖盘滑入插槽，关闭门板并上锁

Conecte el cable de datos SATA/SAS* y el de alimentación en

la parte posterior de la unidad de almacenamiento

* La unidad SATA tiene que conectarse a la controladora

SATA y las unidades SAS a la controladora SAS

Collegare il cavo d’alimentazione ed il cavo dati SATA/SAS*

sulla parte posteriore dell’unità d’archiviazione

* L’unità SATA DEVE essere collegata al controller SATA e le

unità SAS DEVONO essere collegate al controller SAS

Netz- und SATA/SAS*-Datenkabel an der Rückseite des

Speichergerätes anschließen

* SATA-Festplatten MÜSSEN mit dem SATA-Controller und

SAS-Festplatten MÜSSEN mit dem SAS-Controller

verbunden werden

Branchez l'alimentation et le câble de données SATA / SAS* à

l'arrière de l'unité de stockage

* Le lecteur SATA DOIT être connecté au contrôleur SATA et

les lecteurs SAS DOIVENT être connectés au contrôleur SAS

電源およびSATA/SAS*データケーブルをストレージユニ

ットの背面に接続します

* SATAドライブはSATAコントローラに接続し、SASドライブは

SASコントローラに接続する必要があります

连接背面的电源线与SATA/SAS*缆线

* SATA/ SAS需连接至各自相对应的插槽

v 1.01

www.vantecusa.com

Model: MRK-M2504T/MRK-M2508T/MRK-M2512T

L01

L02

L07

L08

B01

B02

B07

B08

L03

L04

L09

L10

B03

B04

B09

B10

L05

L06

L11

L12

B05

B06

B11

B12

D03

D04

D01

D02

D05

D06

D09

D10

D07

D08

D11

D12

P01 P02 P03

F01

SW1

L01

L02

L05

L06

B01

B02

B05

B06

L03

L04

L07

L08

B03

B04

B07

B08

D03

D04

D01

D02

D07

D08

D05

D06

P01 P02

F01

SW1

LED Indicators (L01-L04)

BLUE - Power ON

PURPLE - Disk performing reading/writing

RED - On all 4 LEDs (L0l-L04), constant ashing indicate FAN Failure

NO LED - No power to the drive bay, no drive in the tray

FANS (F01, F02)

Both Fans pull air from the front of the Storage Bays.

It uses two 40x40x20mm Fans.

If any one of the Fans fails, the Four LED (L01- L04) will start blinking RED

Over Heating

If the Four LED (L01 – L04) start to blink RED very rapidly, the temperature in

the Storage Bay have exceeded the safe temperature of 60 degree C.

Power Connector (P05)

Single Power connection for all 4 Bays

LED Function Switch (SW1)

Left

Blue for Power LED

No Disk Activity LED

Red for Fan Failure LED

Right

Blue for Power LED

Purple for Disk Activity LED

Red for Fan Failure LED

SATA/SAS Port Connectors (D01 - D04)

Data port (D01) - B01

Data port (D02) - B02

Data port (D03) - B03

Data port (D04) - B04

Note:

1) You can mix SATA and SAS drives in the same storage unit, but SATA drives

HAVE to be connected to SATA controller and SAS drive HAVE to be connected

to SAS controller

2) SAS drive only support Primary Channel

LED Indicators (L01-L08)

GREEN - Power ON

ORANGE - Disk performing reading/writing

NO LED - No power to the drive bay, no

drive in the tray

LED Temperature Status (T1)

Normal – No LED

Exceeded safe temp of 60 degrees C – Solid RED

LED Fan Status (F1)

Normal – No LED

Fan Failure – Solid RED

FANS (F01)

Fan pulls air from the front of the Storage Bays.

Fan size: 70x70mm

FAN Failure see F1 status

SATA/SAS Port Connectors (D01 - D08)

Data port (D01) - B01

Data port (D02) - B02

Data port (D03) - B03

Data port (D04) - B04

Data port (D05) - B05

Data port (D06) - B06

Data port (D07) - B07

Data port (D08) - B08

Note:

1) You can mix SATA and SAS drives in the same

storage unit, but SATA drives HAVE to be connected to

SATA controller and SAS drive HAVE to be connected

to SAS controller

2) SAS drive only support Primary Channel

L01

D03

D04

SW1

D01

D02

L02

L03

L04

B01

B02

P05

F02 F01

B03

B04

Power Connector (P01,P02)

Dual Power connection for all 8 Bays

Note:

-Both Power connectors must be

connected from the system power supply

-Power load balance by all attached drives

T +, TR - Temperature

F+, FR - Fan

Hdd+, l - HDD activity LED for B01

Hdd+, 2 - HDD activity LED for B02

Hdd+, 3 - HDD activity LED for B03

Hdd+, 4 - HDD activity LED for B04

Hdd+, 5 - HDD activity LED for B05

Hdd+, 6 - HDD activity LED for B06

Hdd+, 7 - HDD activity LED for B07

Hdd+, 8 - HDD activity LED for B08

Signal Extension Connectors

(HDD activity, Fan, Temperature)

HDD activity LED Switch(SW1)

ON – Show Disk Activity (Orange LED)

O – Show only Green Power LED

(If Drive(s) is in the tray)

Fan Speed Switch

Low – 2400 rpm

High – 3000 rpm

LED Indicators (L01-L12)

GREEN - Power ON

ORANGE - Disk performing reading/writing

NO LED - No power to the drive bay, no

drive in the tray

LED Temperature Status (T1)

Normal – No LED

Exceeded safe temp of 60 degree C – Solid RED

LED Fan Status (F1)

Normal – No LED

Fan Failure – Solid RED

FANS (F01)

Fan pulls air from the front of the Storage Bays.

Fan size: 80 x 80 x15mm

FAN Failure see F1 status

SATA/SAS Port Connectors (D01 - D12)

Data port (D01) - B01

Data port (D02) - B02

Data port (D03) - B03

Data port (D04) - B04

Data port (D05) - B05

Data port (D06) - B06

Data port (D07) - B07

Data port (D08) - B08

Data port (D09) - B09

Data port (D10) - B10

Data port (D11) - B11

Data port (D12) - B12

Note:

1) You can mix SATA and SAS drives in the same

storage unit, but SATA drives HAVE to be connected to

SATA controller and SAS drive HAVE to be connected

to SAS controller

2) SAS drive only support Primary Channel

Power Connector (P01,P02,P03

)

Three Power connection for all 12 Bays

Note:

-Three Power connectors must be

connected from the system power supply

-Power load balance by all attached drives

T+, TR - Temperature

F+, FR - Fan

Hdd+, l - HDD activity LED for B01

Hdd+, 2 - HDD activity LED for B02

Hdd+, 3 - HDD activity LED for B03

Hdd+, 4 - HDD activity LED for B04

Hdd+, 5 - HDD activity LED for B05

Hdd+, 6 - HDD activity LED for B06

Hdd+, 7 - HDD activity LED for B07

Hdd+, 8 - HDD activity LED for B08

Hdd+, 9 - HDD activity LED for B09

Hdd+, 10 - HDD activity LED for B10

Hdd+, 11 - HDD activity LED for B11

Hdd+, 12 - HDD activity LED for B12

Signal Extension Connectors

(HDD activity, Fan, Temperature)

HDD activity LED Switch(SW1)

ON – Show Disk Activity (Orange LED)

O – Show only Green Power LED

(If Drive(s) is in the tray)

Fan Speed Switch

Low – 2400 rpm

High – 3000 rpm

Produkt Specifikationer

Mærke:	Vantec
Kategori:	Disk array
Model:	EZ Swap M2500
Bredde:	180 mm
Dybde:	146 mm
Højde:	42 mm
Vægt:	898.1129 g
Produktfarve:	Sort
Kabler inkluderet:	SATA
LED-indikatorer:	Ja
Understøttede Windows-operativsystemer:	Ja
Understøttede Mac-operativsystemer:	Mac OS X 10.0 Cheetah, Mac OS X 10.1 Puma, Mac OS X 10.2 Jaguar, Mac OS X 10.3 Panther, Mac OS X 10.4 Tiger, Mac OS X 10.5 Leopard, Mac OS X 10.6 Snow Leopard, Mac OS X 10.7 Lion, Mac OS X 10.8 Mountain Lion, Mac OS X 10.9 Mavericks
Understøttede Linux-operativsystemer:	Ja
Antal blæsere:	2 blæser(e)
Grænseflade til lagerdisk:	Serial ATA III
Størrelse på lagerdisk:	2.5 "
Understøttet datalagringsdrev typer:	HDD & SSD
Antal understøttede lagerdiske:	4
Dataoverførselshastighed:	6 Gbit/sek.
Total installeret opbevaringskapacitet:	0 TB
Maksimalt understøttet lagerkapacitet:	8 TB
Hot-swap drevbåse:	Ja