Vaxcel T0698 Manual

Vaxcel Ikke kategoriseret T0698

Læs gratis den danske manual til Vaxcel T0698 (10 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Vaxcel T0698, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

Page 1 / 5

Important to Know:

1. If you are not familiar with state and local electrical

codes, it is recommended that you consult with a

qualified electrician.

2. This fixture requires a 120 VAC, 60 Hz power

source.

3. For general safety and to avoid any possible

damage to the sensor, be sure the power is

switched "off" before adjustment.

Maximum Wattage: 26 W

Working Temperature Range: - 13°F ~ 113°F

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ AND SAVE THESE INSTRUCTIONS.

Features:

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

Note: Fixture can be wall mounted or eave mounted.

Wall Mounted

Eave Mounted

Read notes section on page 4 for additional information about mounting location of fixture.

Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation)

Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for

proper operation and to avoid the risk of electrical shock.

1. Energy saving LED fixture.

2. Motion sensor: turns light ON automatically when

motion is detected and turns light OFF or remains

in low-level brightness when motion stops.

3. Photocell keeps the light OFF during daylight hours.

4. When in manual override mode, use wall switch

to keep the light ON full brightness during the night.

Hardware Package (included):

Mounting Strap

Decorative cover

Fixture Mounting Screw

Mounting Screw X2

#8/32X1/2 in

Mounting Screw X2

#6/32 X1/2 in

Mounting Screw X2

#10/24 X1/4 in

Wire Connector Gasket

For eave mounted only:

Swing the sensor head towards the back plate.

Rotate the sensor head clockwise 180˚ so the controls face down.

Controls

Backplate

Controls

T0698 / T0699

(1) Phillips-head Screwdriver

1. Phillips-head screwdriver for attaching mounting screws to

mounting strap, mounting bracket and fixture to mounting bracket.

Tools Needed:

221102

Produkt Specifikationer

Mærke:	Vaxcel
Kategori:	Ikke kategoriseret
Model:	T0698

Har du brug for hjælp?

Hvis du har brug for hjælp til Vaxcel T0698 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Vaxcel Manualer

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Airlive WPOE-10TX804 Manual

17 December 2025

Alice & Fox Cubbie Manual

17 December 2025

Sanus AFAb Manual

17 December 2025

ATen CE801 Manual

17 December 2025

TOTO TSMXW Manual

17 December 2025

NightStick NSR-1514C Manual

17 December 2025

BeamZ Shimmer 2 Manual

17 December 2025

TOTO THU500S Manual

17 December 2025

TOTO Silas TS210C Manual

17 December 2025

Wine-Mate WM-1500HTD-TE Manual

17 December 2025