Vent-A-Hood JDH236C3SS Manual

Vent-A-Hood Emhætte JDH236C3SS

Læs gratis den danske manual til Vent-A-Hood JDH236C3SS (7 sider) i kategorien Emhætte. Denne vejledning er vurderet som hjælpsom af 72 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 36.5 anmeldelser. Har du et spørgsmål om Vent-A-Hood JDH236C3SS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/7

Page 1JDH/C3 0817A

C US

Read and Save These Instructions

All Hoods Must Be Installed By A Qualied Installer

INSTALLATION INSTRUCTIONS

JDH/C3 DESIGNER SERIES

WALL MOUNT HOOD

Read All Instructions Thoroughly Before Beginning Installation

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be done by qualied person(s)

in accordance with all applicable codes and standards, including re-

rated construction. Switch power o󰀨 at service panel and lock the service

disconnecting means to prevent power from being switched on accidentally

during installation.

B. When cutting or drilling into wall or ceiling, do not damage electrical wiring

and other hidden utilities.

C. Ducted fans must always be vented to the outdoors.

D. Su󰀩cient air is needed for proper combustion and exhausting of gases

through the ue (chimney) of fuel burning equipment to prevent back

drafting. Follow the heating equipment manufacturer’s guideline and

safety standards such as those published by the National Fire Protection

Association (NFPA), and the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE), and local code authorities.

E. ASHRAE residential ventilation standard 62.2 limits exhaust fans (total) to

a maximum of 15 CFM per 100 square feet of occupiable space, unless a

back drafting test is performed or make-up air is provided. Consult a local

HVAC engineer for make-up air evaluation.

WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL

DUCTWORK

Page 2JDH/C3 0817A

Ducting Do’s and Don’ts

YES

Smooth Duct Smooth Gradual Turn Proper Combining

of Two Ducts

Flexible Duct Sharp Angled Turns Improper Combining

of Two Ducts

General Requirements

• Observe local codes regarding special duct requirements and placement of duct against combustibles.

• UsingVent-A-Hoodtransitions(backpage)willensurepropere󰀩ciency.

• UsingVent-A-Hoodroofjacksorwalllouvers(backpage)willensurepropere󰀩ciency.

• Where possible, seal joints with duct tape.

• The hood must be ducted to the outdoors without restrictions.

Blower Requirements

• The single blower unit (B100) requires 6” round duct or equivalent (28 square inches), and the dual

blower unit (B200) requires 8” round duct or equivalent (50 square inches).

Blower Combined Duct Dize Vent-A-Hood TransitionSq. Inch Area

Single (B100) 6" round or equivalent 28 sq. in. N/A

Dual (B200) 8" round or equivalent 50 sq. in. N/A

Single and Dual (B100 & B200) 10" round or equivalent 79 sq. in. VP562 (Included)

Two Duals (Two B200s) 12" round or equivalent 113 sq. in. VP563 (Included)

Ducting Requirements

• NEVER reduce the duct size.

• Whencombiningductstogether,thesquareinchareamustreectthetotalsquareinchareaofthe

ducts being combined.

• Donotuseexibleorcorrugatedduct.Thistypeofductwillrestrictairowandreduceperformance.

• Onlyusesmooth,galvanized,metalduct.

• Make the duct run as short and as straight as possible with as few turns as possible.

• Avoid sharp-angled turns. Instead, use smooth, gradual turns such as adjustable elbows or 45 degree

angled turns.

• Forductrunsover20feet,increasetheductdiameterbyoneinchforeverytenfeetofduct.

• A 90 degree elbow is equal to 5 feet of duct.

Termination Requirements

• Airowmustnotberestrictedattheendoftheductrun.

• A wall louver or roof jack is required for each duct run.

• Everywalllouverorroofjackmustincludeagravitydampertopreventbackdrafts.

• Do not use screen wire or spring-loaded doors on wall louvers or roof jacks.

• Donotterminateventingintoanatticorchimney.

Produkt Specifikationer

Mærke:	Vent-A-Hood
Kategori:	Emhætte
Model:	JDH236C3SS

Har du brug for hjælp?

Hvis du har brug for hjælp til Vent-A-Hood JDH236C3SS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Emhætte Vent-A-Hood Manualer

Vent-A-Hood CWEAH6K48SS Manual

2 September 2025

Vent-A-Hood SLH9230SS Manual

5 September 2024

Vent-A-Hood JDH236C3SS Manual

18 August 2024

Vent-A-Hood PRXH18236SS Manual

18 August 2024

Emhætte Manualer

Nyeste Emhætte Manualer

Vivax CHO-60CHC115T B Manual

28 September 2025

Tesy SL 400 LX Manual

28 September 2025

Tesy FS 400 1T 60 WH Manual

28 September 2025

Tesy SL 400 60 LX Manual

28 September 2025

Elektro Helios SF603-3 Manual

28 September 2025

Elektro Helios SF703-3 Manual

28 September 2025

Amana WVW53UC0FS Manual

27 September 2025

Elektro Helios SF504-2 Manual

27 September 2025

Elektro Helios SF704-2 Manual

27 September 2025

Novy Pro'line 7221 Manual

27 September 2025