Vestil EHTT-L Manual

Vestil Ikke kategoriseret EHTT-L

Læs gratis den danske manual til Vestil EHTT-L (18 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Vestil EHTT-L, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/18
03/05 03-126-120.doc
V
ESTIL MFG. CO 1
VESTIL MANUFACTURING CORP.
2999 N. Wayne St., Angola, IN 46703
Ph: 260-665-7586 · Fax: 260-665-1339
E-mail: sales@vestil.com • Website: www.vestil.com
MODELS EM1-200 & -500, EHTT, EHTT-L
Serial number ____________
Installation Instructions ………………......................... 2
Operation Instructions ……………………….……...... 3
Routine Maintenance & Safety Checks ……………… 4
Exploded Structural Parts Drawing & BOM ………... 5-8
Motor and Transformer Connections ............................ 9
Electrical & Hydraulic Diagrams & BOM ……….... 10-12
Power Unit’s Operation ………………...…..………... 13
Troubleshooting …………………………....………… 14
Safety Label Identification ........................................ 15-16
Warranty …………………………………….……..…. 17
WARNINGS AND SAFETY INSTRUCTIONS
Ensure that all employees understand and follow the following.
o Read and understand the owner’s manual before using or servicing
the tilting table.
o The load must be removed, and the platform either positively and
adequately supported or fully tilted, before any work is performed
on the tilter.
o Ensure that all safety and warning labels stay in place and are
legible.
o Do not use the tilting table if any damage or unusual noise is
observed.
o Always watch the platform and the container carefully when the
tilter is in operation.
o Do not perform any modifications to the tilting table without the
manufacturer’s approval. Failure to receive authorization for
changes to the equipment could void the warranty.
o Maintenance and repairs are to be done only by personnel qualified
to perform the required work.
o Do not use brake fluid or jack oils in the hydraulic system. If oil is
needed, use an anti-wear hydraulic oil with a viscosity grade of
150 SUS at 100°F, (ISO 32 cSt @ 40°C), or Dexron transmission fluid.
o Contact the manufacturer for any needed MSDS information.
WHEN ORDERING
REPLACEMENT PARTS:
We take pride in using quality
parts on the equipment we
manufacture. We are not
responsible for equipment
problems resulting from the use
of unapproved replacement
parts.
To order replacement or
spare parts for this equipment,
contact the factory.
In any communication with
the factory please be prepared
to provide the machine’s serial
number, which is indicated on
the machine dataplate.
RECEIVING INSTRUCTIONS
Every unit is thoroughly
tested and inspected prior to
shipment. However, it is
possible that the unit could
incur damage during transit.
Inspect the unit closely when
it arrives. If you see evidence
of damage or rough handling to
either the packaging or to the
product when it is being
unloaded, immediately
make a
note of it on the Bill Of Lading!
It is important that you
remove the product’s packaging
upon its arrival to ensure that
there is no concealed damage
or to enable a timely claim with
the carrier for freight damage.
Also verify that the product
and its specifications are as
ordered.
O
WNER
’
S
MANUAL
EM1
-
200
EM1
-
5
00
EHTT
EHTT-L
03/05 03-126-120.doc
V
ESTIL MFG. CO 2
INSTALLATION INSTRUCTIONS – EM1-200 & -500, EHTT, EHTT-L
Review this entire page before installing the tilting table.
Consult the factory in the event there are any questions or problems at the time of installation, or for
information regarding optional features not covered by the owner’s manual.
The tilting table must be removed from the shipping wood and securely anchored to the floor before use! The
EM1-500 platform must be tilted to the 90° position, and supported if necessary, before removing the shipping wood.
• Modifications or additions to the tilting table without prior manufacturer’s authorization may void the unit’s
warranty. The addition of ancillary equipment to the platform may necessitate that its load capacity be reduced.
• The installation must be made so that it complies with all the regulations applicable to the machine and its
location. The end-user must verify that the supplied equipment is installed so it will be suited to the environment
in which it will be used.
• Installation must be performed by suitably trained personnel with access to the appropriate equipment. The
electrical aspects of the installation should be performed by an electrician.
---------------------------------------------------------------------------------------
For a typical installation of a standard tilting table you will need the following:
1. A fork truck or hoisting means to unload the tilting table from the freight truck and set it into place.
2. A smooth, level, and adequately strong concrete surface on which to mount and operate the tilting table.
3. Concrete anchors, a masonry drill, a masonry bit, hand tools, grout, and steel shims. Consult the building’s
architect or facility engineer to determine the best size and type of hardware with which to anchor the machine to
the floor.
• Units designed to be portable do not need to be anchored to the floor.
4. A power supply circuit and electrical disconnect matching the motor voltage and current requirements. Refer to
the machine’s dataplate, to the labels on the control enclosure, and to the electrical section in this manual for
more information. The end-user is responsible for supplying the branch circuit’s required ground fault and short-
circuit protection. (Motor overload protection is provided by a thermostat built into the motor.)
---------------------------------------
To install a standard non-portable tilting table:
1. Remove the shipping boards from underneath the tilter’s frame.
Caution: On EM1-500’s, tilt the platform down fully (the cylinder will be extended) before removing the boards.
Otherwise, the unit could be top-heavy and tip over unexpectedly.
2. Move the tilter into place with a fork truck having at least a 2,000 lb capacity.
3. Temporarily connect the power supply to the pigtail cord supplied with the tilting table, and tilt the platform to its
maximum angle so that the control enclosure is accessible.
o If the platform must be tilted without first having the proper power supply connected, support under the backstop
side of the platform by either attaching rigging from a crane or hoist, or inserting a lift truck’s forks under the
platform. Carefully unpin one end of the cylinder(s) and allow the platform to tilt to its maximum angle. Once the
power supply is connected, press the LOWER pushbutton to allow the cylinders to retract. (Single-acting cylinders
must be manually compressed in order to retract.) Finally, reinstall the cylinder pin and its hardware.
4.
Anchor the frame to the floor through each anchoring bracket located at the frame’s perimeter using appropriate
concrete anchors.
5. Make permanent connection to the power supply, using an appropriate wiring method.
6. Operate the tilting table through several full raise and lower cycles. Verify that the limit switch(es) functions
properly.
7. Check the hydraulic oil level. It should be within 1” of the reservoir’s fill hole with the cylinders retracted. If oil
is needed, use an anti-wear hydraulic oil with a viscosity grade of 150 SUS at 100°F (ISO 32 at 40°C) or a non-
synthetic automatic transmission fluid.
8. Clean up any debris or spilled oil, and verify that all of the warning and safety labels are in good condition.

Produkt Specifikationer

Mærke: Vestil
Kategori: Ikke kategoriseret
Model: EHTT-L

Har du brug for hjælp?

Hvis du har brug for hjælp til Vestil EHTT-L stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Vestil Manualer

Vestil

Vestil PNU-2472 Manual

18 September 2025
Vestil

Vestil EHTT-L Manual

18 September 2025
Vestil

Vestil LAD-3-W Manual

18 September 2025
Vestil

Vestil D-50-HD Manual

18 September 2025
Vestil

Vestil LAD-FM-120-PSO Manual

18 September 2025
Vestil

Vestil TT-18-7/8 Manual

18 September 2025
Vestil

Vestil D-75-MD Manual

18 September 2025
Vestil

Vestil ATP-C-2436 Manual

18 September 2025
Vestil

Vestil D-33-MD Manual

18 September 2025
Vestil

Vestil LAD-13-14-P Manual

18 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Ambient Weather

Ambient Weather WS-0265 Manual

18 September 2025
Emerson

Emerson BAR322 Manual

18 September 2025
Ambient Weather

Ambient Weather EZ-29-24 Manual

18 September 2025
Newline

Newline TT-8624QPRO Manual

18 September 2025
Babysense

Babysense Dreamer Manual

18 September 2025
Wesco

Wesco 272755 Manual

18 September 2025
Newline

Newline TT-6523QA Manual

18 September 2025
Ambient Weather

Ambient Weather WS-8400 Manual

18 September 2025
Emerson

Emerson ER100803 Manual

18 September 2025
Ambient Weather

Ambient Weather WS-YG501 Manual

18 September 2025