TABLE OF CONTENTS Rev. 1/16/2023 HDC-905 MANUAL
TABLE OF CONTENTS Copyright 2023 Vestil Manufacturing Co. Page 1 of 19
HDC-905 SERIES HYDRAULIC DRUM CRUSHERS
HDC-905-IDC HDC-905-HC
Receiving Instructions
After delivery, remove the packaging from the product. Inspect the product closely to determine whether it sustained
damage during transport. If damage is discovered, record a complete description of it on the bill of lading. If the product
is undamaged, discard the packaging.
NOTE: The end-user is solely responsible for confirming that product design, use, and maintenance comply with laws,
regulations, codes, and mandatory standards applied where the product is used.
Technical Service & Replacement Parts
For answers to questions not addressed in these instructions and to order replacement parts, labels, and
accessories, call our Technical Service and Parts Department at (260) 665-7586. The department can also be
contacted online at https://www.vestil.com/page-parts-request.php.
Electronic Copies of Instruction Manuals
Additional copies of this instruction manual may be downloaded from https://www.vestil.com/page-manuals.php.
Vestil Manufacturing Co.
2999 North Wayne Street, P.O. Box 507, Angola, IN 46703
Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868
Fax: (260) 665-1339
www.vestil.com e-mail: info@vestil.com
Signal Words……………………………………………..…………………………………………………..…..………...
Safety Instructions….……………..……………………………………………..…………………………………...……
Hydraulic Circuit Diagram…….…………………………………………..……………………………………………….
Specifications…………………………………..………………………………………………………..…………..….….
FIG. 1: HDC-905-IDC Exploded View & Bill of Materials……….....……………………………..…………………....
FIG. 2: HDC-905-HC Exploded View & Bill of Materials……………...………………………………………………..
FIG. 3: Power Unit Exploded View & Bill of Materials………...…………………..………………………….………..
FIG. 4: Detailed Parts Breakdown of Manifold Assembly………………….…………………………………..………
FIGURES 5-8: Manifold, Pressure Switches, and Valves……….……….……………………..……………………..
Valve and Pressure Switch Adjustment Procedure………………..……………………….…………………………..
Electrical Controls Sequence of Operation…………………………………………………………………...…………
Electrical System Specifications………………………………………………………………………………………….
FIG. 9: Standard 3-Phase Electrical Circuit Diagram (22124024 rev. F)………………………………………...…..
FIG. 10: 3-Phase Continuous Run Electrical Circuit Diagram (22124025 rev. C)…………………………………..
FIG. 11: Single Phase 115VAC Electrical Circuit Diagram (22124026 rev. D)………………………………..…….
FIG. 12: Single Phase 208/230VAC Electrical Circuit Diagram (22124027 rev. E)………………..……………….
Installation……………………………………………………………………………………………………………….….
Loading the Chamber……………………………………………………………………………………………………...
Operation………….…………………………………………………………………………………………………….…..
Platen Configurations………………………………………………………………………………………………………
Record of Satisfactory Condition…………………………………………………………………………………………
Inspections & Maintenance………..…………………………………………………………………………………..….
Labeling Diagram…………….....………………………………………………………………………………….………
Limited Warranty (all units except “Wash down” model HDC-905-WD)...……………..………………………...…..
Limited Warranty (HDC-905-WD only)…………………………………………………………………………….…….
IMPORTANT NOTE
HDC-900 series crusher-compactors are designed
to compact non-hazardous and low level hazardous
waste materials. They do not include air filtration
systems (e.g. HEPA filters) to remove particulates,
aerosols, volatile compounds, et al. that might be
released from waste materials as a result of
compaction. Review safety messages and
instructions printed on, or provided with, waste
materials (e.g. empty containers or packaging)
before compacting them. If waste material indicates
that it should not be compacted, or should only be
compacted where air filtration is applied, do not use
this machine to compact the material.
