Vestil WT-2221 Manual

Vestil Ikke kategoriseret WT-2221

Læs gratis den danske manual til Vestil WT-2221 (12 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Vestil WT-2221, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/12
1
TILTING WORK TABLE
MODEL WT-2424 & WT-2221
OWNER'S
MANUAL
Revised 09-04 16-126-107
A company dedicated to solving ergonomic and material
handling problems since 1955
.
Ergonomic Solutions
Caster Installation...........................................2
Parts Identification & Drawing (WT-2424) ......3
Parts Identification & Drawing (WT-2221) ......4
Contents
Warnings and Safety Instructions ................. 1
Receiving Instructions .................................. 1
Operating Instructions .................................. 1
WARNINGS & SAFETY INSTRUCTIONS
Read owner's manual completely before operating unit!
• Keep hands and feet away from all moving parts while
table is in use.
• Do not attempt to adjust the height or tilt angle of the
table while a load is sitting on the platform.
• Never stand or sit on the table.
• Remove load before performing any repairs on the table.
• Use only maintenance parts supplied or approved by
the manufacturer.
• Always engage all wheel brakes when table is not being
moved.
• Never exceed the maximum loading capacity of 300 lbs.
• Load must be evenly distributed on table to ensure
maximum stability.
• Always make sure the height adjustment screw is
securely tightened before a load is applied especially
after table has been raised or lowered.
• Failure to follow these guidelines may result in personal
injury and/or property damage.
RECEIVING INSTRUCTIONS
Every unit is thoroughly tested and inspected prior
to shipment. However, it is possible that the unit may incur
damage during transit. If you see damage when unloading
make a note of it on the SHIPPER RECEIVER.
Remove all packing and strapping material and
inspect for damage. IF DAMAGE IS EVIDENT, FILE A
CLAIM WITH THE CARRIER IMMEDIATELY!
OPERATING INSTRUCTIONS (WT-2424)
1) Position the work table near the desired work area.
2) Lock all four casters.
TILTING WORK TABLE
MODEL WT-2424 & WT-2221
3) Loosen the height adjustment screw and adjust the
work table to the desired height using the handwheel
located on the base frame.
4) Tighten the height adjustment screw.
5) Adjust the tilt angle of the table to the desired position
using the handwheel directly under the table platform.
6) Place the load on table carefully.
OPERATING INSTRUCTIONS (WT-2221)
1) Position the work table near the desired work area.
2) Lock all four casters.
3) Adjust the height to the correct level by star knob
adjustment located on the center column and sliding it
up or down.
4) Loosen the tilt adjustment knob under platform. Tilt
deck to desired angle and retighten.
5) Place the load on the table.
E
N
G
L
I
S
H
E
S
P
A
N
O
L
F
R
A
N
Ç
A
I
S
VESTIL MANUFACTURING CORPORATION
2999 North Wayne Street
Angola, IN 46703 USA
Phone (260) 665-7586 • Fax (260) 665-1339
sales@vestil.com • www.vestil.com
2
CASTER INSTALLATION INSTRUCTIONS
Securely prop up one end of the carts frame high enough for the casters to fit underneath that end. You will see four
caster mounting brackets welded to the bottom of the carts frame, one at each corner.
If you have both swivel and rigid casters, the casters are to be mounted in adjacent pairs. Typically, the swivel casters
are mounted to the side on which the push handle is located (when applicable). Determine the proper locations for the
casters before you begin.
Turn the included machine screws a couple of threads into the two threaded holes in the ends of each of the caster
mounting brackets.
To install the casters onto the cart:
Insert either of the short sides of the caster’s top plate into the curled end of the caster mounting bracket.
Raise the other end of the caster’s top plate up into the mounting bracket, and secure it there by screwing in the
machine screws completely. The screws should extend underneath the caster’s top plate, thereby retaining it in the
bracket.

Produkt Specifikationer

Mærke: Vestil
Kategori: Ikke kategoriseret
Model: WT-2221

Har du brug for hjælp?

Hvis du har brug for hjælp til Vestil WT-2221 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Vestil Manualer

Vestil

Vestil LPRO-36-16-4 Manual

17 September 2025
Vestil

Vestil CPC-20 Manual

17 September 2025
Vestil

Vestil UNI-4048-4-BLU-230-1 Manual

17 September 2025
Vestil

Vestil CANT-3648 Manual

17 September 2025
Vestil

Vestil H-75-LD Manual

17 September 2025
Vestil

Vestil LAD-MM-12-P Manual

17 September 2025
Vestil

Vestil DSHZ-4 Manual

17 September 2025
Vestil

Vestil UNI-4048-4-BLU-115-1 Manual

17 September 2025
Vestil

Vestil UNI-5448-4 Manual

17 September 2025
Vestil

Vestil WT-2221 Manual

17 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vulcan

Vulcan VBP15SL Manual

17 September 2025
Rocktrail

Rocktrail IAN 463536 Manual

17 September 2025
Kimo

Kimo KNT 320 Manual

17 September 2025
InLine

InLine 16277S Manual

17 September 2025
Fulgor Milano

Fulgor Milano P1B 5343 QU Manual

17 September 2025
Ikea

Ikea BÅTSKÄR 405.533.91 Manual

17 September 2025
Lakeside

Lakeside 913 Manual

17 September 2025
Haws

Haws 3611 Manual

17 September 2025
Wesco

Wesco 260207 Manual

17 September 2025
KStrong

KStrong UFA30001 Manual

17 September 2025