Viessmann 5229 Manual


Læs gratis den danske manual til Viessmann 5229 (16 sider) i kategorien Modelbygning. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Viessmann 5229, eller vil du spørge andre brugere om produktet?

Side 1/16
Gebrauchsanleitung
5229
Multiplexer
für Lichtsignale mit Multiplex-Technologie
for daylight signals
with multiplex-technology
1. Wichtige Hinweise ...................................... 2
2. Einführung / Eigenschaften ........................ 2
3. Anschluss ................................................... 3
4. Kon guration .............................................. 6
5. Signalbus ................................................... 10
6. Signal-Logik ............................................... 11
7. Technische Daten ...................................... 16
1. Important Information ................................. 2
2. Introduction / Properties ............................. 2
3. Connections ............................................... 3
4. Con guration .............................................. 7
5. Signalbus ................................................... 10
6. Signal Logic ............................................... 11
7. Technical Data ........................................... 16
5229_92349_01_DE-EN.indd 1 12.09.2008 15:22:16
2
DE EN
1. Wichtige Hinweise
Lesen Sie vor der ersten Benutzung des Produk-
tes bzw. dessen Einbau diese Anleitung komplett
und aufmerksam durch. Bewahren Sie diese An-
leitung auf. Sie ist Teil des Produktes.
Das Produkt richtig verwenden
Das Produkt darf ausschließlich dieser Anleitung
gemäß verwendet werden. Dieses Steuermodul
ist bestimmt
– zum Einbau in Modelleisenbahnanlagen,
– zum Anschluss an einen zugelassenen Modell-
bahntransformator mit einer Ausgangsspan-
nung von max. 16 V~ bzw. an einer damit ver-
sorgten Steuerung (z. B. 5200 oder Viessmann
Viessmann Commander 5300),
– zum Betrieb in trockenen Räumen.
– zur Ansteuerung von Signalen
mit Multiplex-Technologie
Jeder darüber hinausgehende Gebrauch gilt als
nicht bestimmungsgemäß. Für daraus resultie-
rende Schäden haftet der Hersteller nicht.
2. Einführung / Eigenschaften
Der Multiplexer 5229 steuert ein zwei- oder mehr-
begrifges Tageslicht-Signal mit dem dazu gehö-
renden Vorsignal. Das Signal muss mit der Viess-
mann Multiplextechnik ausgestattet sein.
Der Multiplexer kann folgende Signale steuern:
Viessmann Ks-Signale 4040 - 4046 und
Viessmann Lichtsignale 4720 - 4730.
Signalbilder und Adressen nden Sie auf Seite 15.
Der Multiplexer erkennt automatisch den Typ des
angeschlossenen Signals. Er konguriert sich ent-
sprechend automatisch. In Verbindung mit dem
Commander (Anschluss am LSB) kann sich das
Modul auch auf alle weiteren Parameter (z. B. Di-
gitaladressen) automatisch kongurieren, so dass
keine manuellen Einstellungen nötig sind.
Bei Verwendung anderer Digitalzentralen bzw.
im analogen Betrieb werden Optionen über DIP-
Schalter (s. a. Abb. 4 auf S. 7) und gegebenenfalls
Digitaladressen manuell eingerichtet. Bei diesem
Vorgang werden gleichzeitig die Eigenschaften
des zu steuernden Signals konguriert:
sofortiges oder weiches Überblenden
der Signalbilder
gekoppeltes Signal
Bahnhofs- oder Blocksignal-Logik
Bremsgenerator ja / nein
Please read this manual prior to rst use of the
product resp. its installation! Keep this manual. It
is part of the product.
This product must only be used as required in
this manual. This model of a signal is intended
– for installation in model railroad layouts,
– for connection to an authorized model railroad
transformer with an output voltage of max.
16 V~ or an electrical control system connect-
ed to one (e. g. 5200 or Viessmann Viessmann
Commander),
– for operation in a dry area.
for connection to a daylight signal with
multiplex technology
Using the product for any other purpose is not
approved and is considered incorrect. The
manufacturer cannot be held responsible for any
damage resulting from the improper use of this
product.
The module 5229 „Multiplexer“ controls a two-
aspect or a combined-aspect daylight signal and
the appropriate distant signal. The signal must be
equipped with the multiplex-technique. Viessmann
The Multiplexer can operate the following signals:
Viessmann Ks-signals 4040 – 4046 and
Viessmann light signals 4720 – 4730
For signal aspects and addresses, refer to p. 15.
The Multiplexer identies automatically the type
of the connected signal. The conguration is done
automatically. In case that the module is connect-
ed to the (connection to the LSB) it Commander
is also enabled to execute the autoconguration
of all further parameters (e.g. digital address). No
manual adjustment is necessary then.
In combination with other digital command sta-
tions respectively with conventional systems, op-
tions and digital addresses can be adjusted by
a DIP-switch manually (see illustration Nr. 4 on
page 7). The features of the signal you want to
operate are programmed synchronously:
immediate and soft fade-over of signal aspects
coupled signal
station block- or block signal logic
brake generator yes/ no
5229_92349_01_DE-EN.indd 2 12.09.2008 15:22:16


Produkt Specifikationer

Mærke: Viessmann
Kategori: Modelbygning
Model: 5229

Har du brug for hjælp?

Hvis du har brug for hjælp til Viessmann 5229 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Modelbygning Viessmann Manualer

Viessmann

Viessmann 4516 Manual

14 Januar 2025
Viessmann

Viessmann 5268 Manual

31 August 2024
Viessmann

Viessmann 4568 Manual

29 August 2024
Viessmann

Viessmann 4045 Manual

13 August 2024
Viessmann

Viessmann 4200 Manual

6 August 2024
Viessmann

Viessmann 2316 Manual

31 Juli 2024
Viessmann

Viessmann 4570 Manual

29 Juli 2024
Viessmann

Viessmann 5229 Manual

27 Juli 2024
Viessmann

Viessmann 4042 Manual

27 Juli 2024
Viessmann

Viessmann 6337 Manual

27 Juli 2024

Modelbygning Manualer

Nyeste Modelbygning Manualer