Vimar 03975.N Manual

Vimar Ikke kategoriseret 03975.N

Læs gratis den danske manual til Vimar 03975.N (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Vimar 03975.N, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Viale Vicenza 14

36063 Marostica VI - Italy

www.vimar.com

03975 03 2202

03975 - Voice control with 2 push buttons and actuator

SMART HOME

Alexa built-in voice control device with built-in Wi-Fi, two front buttons, RGB LED backlighting, 1

input for wired push button, 1 relay output for local or remote control, designed for use on View

Wireless mesh system thanks to IoT technology on Bluetooth technology 5.0 standard and on

By-me Plus system thanks to the By-me bus - 3 modules.

THREE OPERATING MODES (ALTERNATIVE)

Stand alone View Wireless System By-me Plus System• •

Stand alone View Wireless System By-me Plus System

Front

buttons

Relay ON-

OFF control.

Configuration with

View App.

Relay ON-OFF control.

Configuration with

View Wireless App and

management from View App.

Freely configurable

with the View Pro App.

Management from

View App.

Relay

It is controlled from

the front buttons

and from the remote

wired push button.

It is controlled from the

front buttons and from the

remote push button.

Freely configurable

with the View Pro App.

Remote

push button

Relay ON-OFF

control.

Relay ON-OFF control or

scenario activation.

Freely configurable

with the View Pro App.

Download the View App from the stores onto the tablet/smartphone you will be

using for configuration.

Depending on the mode you you will also need:select,

Stand alone View Wireless System By-me Plus System

Nothing else

Gateway

art. 20597-19597-16497-14597

Home automation system gateway

art. 01410 or 01411

View Wireless App for

configuration in the system

View Pro App for

configuration in the system

IMPORTANT: In View Wireless and By-me Plus systems, relays, buttons and push buttons

should always be configured first. Subsequently, the voice control should be configured

using the View App.

CONFIGURATION IN THE VIEW WIRELESS SYSTEM

1. Create your Installer account on MyVimar (on-line).

2. Wire all the devices in the system (2-way switches, relays, thermostats, gateway, etc.).

3. Start the View Wireless App and log in with the credentials you just created.

4. Create the system and the environments.

5. Associate all the devices with the environments, except for the gateway (which should be

associated last).

To associate the device 03975 in order to manage its relay output:

• Select “Add” ( ), choose the environment to place it and give it a name

• Select ; activate the Bluetooth connection on your tablet/smartphone and approach the

device

• Simultaneously press button G followed by button E for 5 s; set the function of the relay, the

parameters and any wired control with the related function.

6. For every connected device, set the function, the parameters and any accessory devices

(wired or radio control and related function).

7. Transfer the configuration of the devices to the gateway and connect it to the Wi-Fi network.

8. Transfer the system to the Administrator user (who must have created his/her profile on

MyVimar).

For details please refer to the View Wireless App manual you can download from www.

vimar.com  DOWNLOAD  APP MOBILE  View Wireless

CONFIGURATION IN THE BY-ME PLUS SYSTEM

1. Create your Installer account on MyVimar (on-line).

2. Wire all devices in the system (gateway, touch screen, relay, thermostats, etc.).

3. Start the View Pro App and log in with the credentials you just created.

4. Create the system and enrol the gateways and touch screens

5. Create the environments, enrol the devices and create the applications.

To enrol the device 03975 in order to manage its two front buttons and its relay output:

• Choose the environment in which to place it and select

• Select “START” and simultaneously press button followed brieﬂy by G D

6. For each device, set the functions and parameters

7. Transfer the system to the Administrator user (who must have created his/her profile on

MyVimar).

For details, please refer to the manuals for the VIEW IoT Smart System platform and

the By-me Plus system you can download from www.vimar.com DOWNLOAD APP  

MOBILE  View Pro

VOICE CONTROL CONFIGURATION

1. Create your Administrator account on MyVimar (on-line).

2. Wire the voice controls and any wired push buttons

3. Start the View App and log in with the credentials you just created.

4. To associate the voice control:

• For the Stand alone mode only, select “Create smart ecosystem” and give it a name.

• Activate the Bluetooth connection and geolocation on your tablet/smartphone

• For the Stand alone mode, select the ecosystem you just created “Customise” “Add  

device”.

• For integration with View Wireless and By-me Plus systems, select the system 

“Customise”  “Smart devices”  “Add” ( ).

• Press button G for 5 s

• Press “Start” and follow the instructions of the configuration wizard

5. Create your Amazon account (or use the one you already have) and log in.

6. Activate the Vimar Skill in the Alexa App and control the device by voice.

Functions supported

Amazon Music Streaming and TuneIn

Kindle

Basic conversation

Multi-turn conversation

Announce

For details please refer to the View App manual you can download from www.vimar.com

   DOWNLOAD APP MOBILE View

CONTROLLABLE LOADS

Loads

100 V~ 250 W 50 W 60 W 125 VA

240 V~ 500 W 100 W 120 W 250 VA

RESTART, RESET AND RESTORE TO FACTORY SETTINGS

Stand alone View Wireless System By-me Plus System

Restart the device Press button for 30 sB

Resetting the Wi-Fi

configuration and Alexa Press button for 30 sG

Restore to

factory settings

Concurrently with

resetting the Wi-

Fi configuration

and Alexa

Within the first 5

minutes of powering

the device, press

buttons G and E

simultaneously for 30 s

After resetting the

device from the

View Pro App, press

buttons and G C

simultaneously.

When the operation is complete, the illuminated ring is turned off.

INSTALLATION RULES

• Installation and configuration must be carried out by qualified persons in compliance with the

current regulations regarding the installation of electrical equipment in the country where the

products are installed.

• The device must be installed in flush mounting boxes or surface mounting boxes with Eikon,

Arkè, Idea (with dedicated mounting frame 16723) and Plana mounting frames and cover

plates.

• The device should only be installed horizontally at a height of between 0.8 and 1.6 m from floor

level.

• To ensure correct device operation do not install it near any obstacles.

• The relay output power circuit must be protected against overloads by installing a device, fuse

or automatic 1-way switch, with a rated current not exceeding 10 A.

CHARACTERISTICS

• Rated supply voltage: 100-240 V~, 50/60 Hz.

• Maximum consumption: 2 W

• RF transmission power: < 100mW (20dBm).

• Frequency range: 2400-2483.5 MHz.

• Terminals:

- 2 terminals (L and N) for line and neutral

- 1 terminal (P) for connection to the remote wired push button (for instance art. 20008-

19008-16080-14008). The max distance between the IoT device and the push button is

50 m with a cable with a minimum cross-section of 1.5 mm

- 1 terminal (1) for the relay output in voltage NO 100-240 V 50/60 Hz

• The radio control 03925 cannot be used as an accessory device for the voice assistant

Viale Vicenza 14

36063 Marostica VI - Italy

www.vimar.com

03975 03 2202

03975 - Voice control with 2 push buttons and actuator

SMART HOME

• 4 front buttons delimited by an illuminated ring which, depending on the colour, identifies the

statuses of the vocal function

• 2 front buttons fitted with RGB LEDs with configurable colour

• Absorption from the bus (when used in the By-me Plus system): 1 mA

• Max number of devices 03975 that can be connected in the By-me Plus system: see para.

“System restrictions” in the VIEW IoT Smart System platform manual

• Operating temperature: -5 ÷ +45 °C (indoor)

• Protection degree: IP20

OPERATION

Stand alone

In this case, the 2 front buttons with RGB LED (colour configurable from the View App) and

any remote push button control the relay. Configuration of the device (Wi-Fi credentials and

connection to the Amazon account) is carried out from the View App. Once Alexa is up and

running and the Vimar skills have been enabled, the relay can be voice operated. The relay can

also be controlled from the Google Home App, from the respective voice assistant.

View Wireless System

In this case the 2 front buttons with RGB LED (colour configurable from the View Wireless App)

control the relay, while the remote wired push button can be configured to control the relay or

activate a scenario. Limited to the push buttons and relay, the device can also operate in the

absence of Wi-Fi connectivity. Configuration of the device in the system is carried out from the

View Wireless App. Configuration (Wi-Fi credentials and connection to the Amazon account) is

carried out from the View App. Once Alexa is up and running and the Vimar skills have been

enabled, the connected system can be voice operated. The system can also be controlled from

the Google Home App, from the respective voice assistant and from Siri.

By-me Plus System

In this case, the 2 front buttons with RGB LED (colour configurable from the View App), any

remote wired push button and the relay can be used within applications and scenarios. Limited

to the push buttons and relay, the device can also operate in the absence of Wi-Fi connectivity.

Configuration of the device in the system is carried out from the View Pro App. Configuration

(Wi-Fi credentials and connection to the Amazon account) is carried out from the View App.

Once Alexa is up and running and the Vimar skills have been enabled, the home automation

system can be voice operated. The system can also be controlled from the Google Home App,

from the respective voice assistant and from Siri.

REGULATORY COMPLIANCE.

RED Directive. RoHS directive.

EN 60669-2-5, EN 50491, EN 301 489-17, EN 300 328, EN 62311, EN IEC 63000, EN 55032,

EN 55035, EN 61000-3-2, EN 61000-3-3 standards.

Vimar SpA declares that the radio equipment complies with Directive 2014/53/EU. The full text

of the EU declaration of conformity is on the product sheet available on the following website:

www.vimar.com.

REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces of lead.

WEEE - User information

The crossed bin symbol on the appliance or on its packaging indicates that the product at the end of its life must be collected separately

from other waste. The user must therefore hand the equipment at the end of its life cycle over to the appropriate municipal centres for the

differentiated collection of electrical and electronic waste. As an alternative to independent management, you can deliver the equipment

you want to dispose of free of charge to the distributor when purchasing a new appliance of an equivalent type. You can also deliver

electronic products to be disposed of that are smaller than 25 cm for free, with no obligation to purchase, to electronics distributors with a

sales area of at least 400 m

2. Proper sorted waste collection for subsequent recycling, processing and environmentally conscious disposal

of the old equipment helps to prevent any possible negative impact on the environment and human health while promoting the practice of

reusing and/or recycling materials used in manufacture.

The Apple, iPhone and iPad logos are trademarks of Apple Inc., registered in the United States and in other Countries

and Regions. App Store is a service trademark of Apple Inc. Google is a trademark of Google LLC. Amazon, Alexa and

all related logos are trademarks of Amazon.com, Inc. or its afﬁliates.

INSTALLATION

21613

A005248

MADE

IT ALY

Produkt Specifikationer

Mærke:	Vimar
Kategori:	Ikke kategoriseret
Model:	03975.N

Har du brug for hjælp?

Hvis du har brug for hjælp til Vimar 03975.N stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Vimar Manualer

Vimar EZS10.GA Manual

2 April 2025

Vimar ELVOX 1358 Manual

12 Januar 2025

Vimar 01585 Manual

12 Januar 2025

Vimar 20136.120.B Manual

11 Januar 2025

Vimar 20457.TR.B Manual

29 December 2024

Vimar 20457.TR.N Manual

29 December 2024

Vimar 19457.TR.B Manual

29 December 2024

Vimar 20537 Manual

15 December 2024

Vimar 19593.M Manual

15 December 2024

Vimar 20537.B Manual

15 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Planet XGPN-100 Manual

15 Juni 2025

Proficook PC-EKA 1283 Manual

15 Juni 2025

OmniMount OBSP8 Manual

15 Juni 2025

Levenhuk FS10 Manual

15 Juni 2025

Vestil PM4-2148-LP Manual

15 Juni 2025

ElectriQ STRV-W1-B Manual

15 Juni 2025

Adler AD 4521 Manual

15 Juni 2025

AMX HydraPort HPX-AV102 Manual

15 Juni 2025

Hughes & Kettner Red Box Mk II Manual

15 Juni 2025

Hughes & Kettner Quantum QC 412 Manual

15 Juni 2025