Vivanco UR S2 Manual

Vivanco Fjernbetjening UR S2

Læs gratis den danske manual til Vivanco UR S2 (34 sider) i kategorien Fjernbetjening. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Vivanco UR S2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/34

UR S2 UNIVERSAL TV- DVB CONTROLLER

Vivanco GmbH, D-22926 Ahrensburg, E-Mail

: hotline@vivanco.de

, 1

(GB) Instructions 1 

(D) Bedienungsanleitung 3 

(F) Notice d’emploi 5 

(E) Instrucciones para el uso 7 

(I) Istruzioni per l’uso 9 

(NL) Gebruiksaanwijzing 11 

(PL) Instrukcja obsługi 13 

(CZ) Návod k obsluze 15 

(P) Manual de instruções 17 

(N) Bruksanvisning 19 

(DK) Betjeningsvejledning 21 

(S) Bruksanvisning 22 

(FIN) Käyttöohje 24 

(RUS)

Руководство по эксплуатации

 26

(GR) 28 Οδηγίες χρήσης 

(SK) Návod na obsluhu 31 

Vivanco Addresses 33 

(GB) Instructions

VIVANCO UR S2 Remote Control

Inserting the batteries

Open the battery flap on the back of

the remote control, press the tongue

lightly downwards, then insert 2

alkaline AA batteries. Check that the

polarity markings on the batteries and

in the battery compartment are

correctly lined up (+=+), then close the

flap carefully. – Always use

undamaged batteries.

Adapting to appliances

In order to control e.g. your TV or DVB

you must adapt or set the remote

control to it. There are two ways of

doing so: direct control code entry or

code search.

Direct control code entry using the

enclosed list

Example: setting to control a

Panasonic television set:

1. The attached list gives, for

example, the Panasonic Code 176.

Please make sure you have selected

the correct list for television sets (TV).

2. To prepare code entry,

press the button, keep it pressed SET

and then press the required appliance

button, e.g. , additionally until the TV

lamp (LED) lights constantly.

3. Then press the number

buttons (e.g. 1 7 6) in sequence.

4. Once the numbers have

been entered the lamp goes out and

the remote control is ready to control

your appliance.

5. Finally, test the control

code setting by trying to control (in this

example) your television set. If it does

not work at all or not correctly try a

different code from the list or the code

search (see below).

You can terminate the mode by

pressing any device button.

UR S2 UNIVERSAL TV- DVB CONTROLLER

Vivanco GmbH, D-22926 Ahrensburg, E-Mail

: hotline@vivanco.de

, 2

Code search

If the brand of your appliance is not in

the list or none of the codes given fits,

we recommend a code search.

Manual code search

1. Switch on the appliance to

be controlled. Program is running.

2. To prepare code search,

press the SET button, keep it pressed

and then press the required appliance

button, e.g. , additionally until the TV

lamp (LED) lights constantly.

3. Then point the remote

control at the appliance to be

controlled.

4. Briefly press the SET

button once. The lamp (LED) blinks.

5. Press the ON/OFF

(appliance on/off) button repeatedly

for testing the next code, approx.

every 1,5 seconds, until the appliance,

e.g. your TV reacts by power off.

- If your appliance has switched itself

off you must switch it back on again,

e.g. on the appliance or with the

original remote control, to continue

searching. - When your appliance

reacts you can also try out other

buttons without interrupting the

search. If some buttons do not work

properly, simply continue searching

with ON/OFF.

6. When your appliance

reacts correctly, press the appliance

button, e.g. TV, and end the search.

The lamp (LED) goes out.

- The continues with the search UR S2

at the point where you interrupted it. .

The code last entered remains stored.

The search stops after approx. 30

seconds of inactivity.

Automatic code search

Your remote control finds the correct

settings almost automatically in

seconds:

1. Switch on the appliance to

be controlled. A channel number, for

example, appears in the display of

your satellite receiver.

2. To start the code search,

press the required appliance button,

e.g. briefly. DVB

3. Then press for about SET

5 seconds until the lamp (LED) starts

to blink.

4. Then point the remote

control at the appliance to be

controlled while the remote control

emits a different ON/OFF signal every

second.

5. When your appliance

reacts, press within 1-2 seconds, SET

to end the search. – If you ended the

search too late, continue to search

using the Manual Code Search (see

above).

6. Finally, test the control

code setting by trying to control, for

example, your DVB appliance. If it

does not work correctly, please try the

code search again. The code search

then begins with the next code in the

sequence. - Remember to switch your

appliance, e.g. DVB, back on again if

you wish to continue searching.

Code identification

You can read off the 3-digit codes you

have set at any time:

1. Press the appliance button

of the appliance which code you want

to read off, e.g. . TV

2. Press the button and SET

1,2,3, depending on the part of the

code you want to read off. For

example, if you press + after TV SET 1

and the code 176 (in this example)

has been set, the lamp blinks once

after is released to show that SET+1

the hundred figure is 1. All

you have to do is count. The ten figure

is indicated after + is released, SET 2

e.g. it blinks 7 times for the 7 in 176.

The one figure is indicated after

SET 3+ is released, e.g. it blinks 6

times for the 6 in 176.

- Please open the battery

compartment and write down the

found codes, for later use, onto the

sticker placed at the innerside of the

compartment door.

Produkt Specifikationer

Mærke:	Vivanco
Kategori:	Fjernbetjening
Model:	UR S2

Har du brug for hjælp?

Hvis du har brug for hjælp til Vivanco UR S2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fjernbetjening Vivanco Manualer

Vivanco vivcontrol 5 se Manual

26 August 2024

Vivanco UR12NB Manual

26 August 2024

Vivanco vivcontrol 3 se Manual

26 August 2024

Vivanco UR 1200 Manual

17 August 2024

Vivanco 37600 Manual

16 August 2024

Vivanco Viv.Control 3 Manual

15 August 2024

Vivanco UR 1250 Manual

15 August 2024

Vivanco UR ZAP2 Manual

14 August 2024

Vivanco UR Z2 Manual

14 August 2024

Vivanco UR S2 Manual

14 August 2024

Fjernbetjening Manualer

Nyeste Fjernbetjening Manualer

Neets 310-0202 Manual

27 September 2025

DiO 54791 Manual

26 September 2025

Somfy Keygo RTS Manual

26 September 2025

Spaun SKP 5 Manual

25 September 2025

Crestron HR-310 Manual

24 September 2025

REVO RBL-N Manual

20 September 2025

Philips SRP6207 Manual

19 September 2025

RADEMACHER DuoFern Handzentrale 9493 Manual

17 September 2025

LG MR25GA Manual

16 September 2025

RADEMACHER DuoFern Mehrfachwandtaster 9494-1 Manual

16 September 2025