Vivotek AP-GIC-010A-030 Manual

Vivotek Ikke kategoriseret AP-GIC-010A-030

Læs gratis den danske manual til Vivotek AP-GIC-010A-030 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Vivotek AP-GIC-010A-030, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

VIVOTEK INC.

6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.

| | |T: +886- 2-82455282 F: +886-2-82455532 E: sales@vivot ek.com

VIVOTEK USA, INC.

2050 Ringwood Avenue, San Jose, CA 95131

| | |T: 408-773-8686 F: 408-773-8298 E: salesusa@vivotek.com

VIVOTEK Netherlands B.V.

Busplein 36, 1315KV, Almere, The Netherlands

| | |T: +31 (0)36 5389 149 F: +31 (0)36 5389 111 E: saleseurope@vivot ek.com

Non-PoE Switch

Data INP+D OUT

100~240V AC

PoE

PWR

1. Use CAT5 or 5e UTP/STP cables.

2. AC input (100~240V/AC, 50~60Hz), for a max. consumption of 30W.

AP-GIC-010A(B)-030 PoE Injector

Quick Installation Guide

Model Description

AP-GIC-010A-030 GE Standard 802.3at 30W output

AP-GIC-010B-030 GE Passive 30W output.

(The PoE output should only be connected to an IP camera. It should not be

connected to non-PoE devices, such as a PC's LAN port)

IMPORTANT:

INTRODUCTION

CONNECTION

* 1x PoE injector * 1x AC power cord

* 1x Quick Installation Guide

PACKAGE CONTENTS

All specications are subject to change without noice.

Installation Steps:

1. Connect the included AC power cord to the injector. The Power LED (Green) should be lit.

2. Connect the Data IN port to a LAN switch using an Ethernet cable.

3. Connect the Power+Data OUT port to a powered device, i.e., IP camera, using another Ethernet cable. Make sure the

PoE LED (Yellow) is lit.

4. Check if the powered device (IP camera) is working properly. An IP camera may take up to 1 or 2 minutes to power up.

P/N: 625028600G

The AP-GIC-010B-030 GE does not support the following models:

FD8381-EV, IB8381-E, FE8181(V), FE8391

These models come with PoE detection. They will consider the "Passive" injector as an ordinary 802.3af power source,

and hence will only draw 15 watts of power from it. 15 watts is insufcient for driving the onboard heater and IR lights.

IMPORTANT:

Produkt Specifikationer

Mærke:	Vivotek
Kategori:	Ikke kategoriseret
Model:	AP-GIC-010A-030
Vekselstrømsindgangsspænding:	100 - 240 V
Vekselstrømsindgangsfrekvens:	50 - 60 Hz
Bredde:	64 mm
Dybde:	146 mm
Højde:	42 mm
Vægt:	200 g
Produktfarve:	Sort
Opbevaringstemperatur (T-T):	-20 - 70 °C
Relativ luftfugtighed ved drift (H-H):	10 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	10 - 90 %
Strømforbrug (typisk):	35 W
Driftstemperatur (T-T):	0 - 50 °C
Kabler inkluderet:	Vekselstrøm
Certificering:	CE, C-Tick, FCC, VCCI, LVD
Netværksstandarder:	IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
LED-indikatorer:	PoE, Power
Strøm over Ethernet (PoE):	Ja
Total Power over Ethernet (PoE):	30 W
Kobber ethernet kabelteknologi:	10BASE-T, 100BASE-TX, 1000BASE-T
Basis omskiftning RJ-45 Ethernet porte, antal:	1
Basis omskiftning RJ-45 Ethernet porttype:	Gigabit Ethernet (10/100/1000)
MAC adresselabel:	- entries
Switch kapacitet:	- Gbit/sek.
Strømbeskyttelsesfunktioner:	Over current, Short circuit
Power over Ethernet (PoE) porte, antal:	1