Vivotek MDR-10 Manual

Vivotek Ikke kategoriseret MDR-10

Læs gratis den danske manual til Vivotek MDR-10 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 40 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 20.5 anmeldelser. Har du et spørgsmål om Vivotek MDR-10, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

MDR- 10 series

10W Single Output Industrial DIN Rail Power Supply

File Name:MDR- -SPEC 2017-1110

SPECIFICATION

 Features:

• Universal AC input / Full range

• Protections: Short Circuit / Overload / Over voltage

• Cooling by free air convection

• Can be installed on DIN rail TS-35/7.5 or 15

• Built in DC OK active signal

• LED indicator for power on

• No load power consumption<0.75W

• 100% full load burn-in test

MODEL

MDR- -10 12

OUTPUT

DC VOLTAGE

12V

RATED CURRENT

0.84A

CURRENT RANGE

0 ~ 0.84A

RATED POWER

10W

RIPPLE & NOISE (max.) Note.2

120mVp-p

VOLTAGE TOLERANCE Note.3

±3.0%

LINE REGULATION

±1.0%

LOAD REGULATION

±3.0%

SETUP, RISE TIME Note.5

500ms, 30ms/230VAC 1000ms, 30ms/115VAC at full load

HOLD UP TIME (Typ.)

120ms/230VAC 25ms/115VAC at full load

INPUT

VOLTAGE RANGE

85 ~ 264VAC 120 ~ 370VDC

FREQUENCY RANGE

47 ~ 63Hz

EFFICIENCY (Typ.)

81%

AC CURRENT (Typ.)

0.33A/115VAC 0.21A/230VAC

INRUSH CURRENT (Typ.)

COLD START 35A/115VAC 70A/230VAC

LEAKAGE CURRENT

<1mA / 240VAC

PROTECTION

OVERLOAD

Above 105% rated output power

Protection type : Hiccup mode, recovers automatically after fault condition is removed

OVER VOLTAGE

13.8 ~ 16.2V

Protection type : Shut down o/p voltage, re-power on to recover

FUNCTION

DC OK ACTIVE SIGNAL (max.)

9 ~ 13.5V / 40mA

ENVIRONMENT

WORKING TEMP.

-20 ~ +70 (Refer to "Derating Curve")℃

WORKING HUMIDITY

20 ~ 90% RH non-condensing

STORAGE TEMP., HUMIDITY

-40 ~ +85 , 10 ~ 95% RH℃

TEMP. COEFFICIENT

±0.03%/ (0 ~ 50℃ ℃)

VIBRATION

Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6

SAFETY &

EMC

(Note 4)

SAFETY STANDARDS

UL508, TUV EN60950-1 approved

WITHSTAND VOLTAGE

I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC

ISOLATION RESISTANCE

I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃

EMC EMISSION

Compliance to EN55011, EN55022 (CISPR22), EN61204-3 Class B, EN61000-3- -32,

EMC IMMUNITY

Compliance to EN61000-4-2, 3, 4, 5, 6, 8, 11, EN55024,EN61000-6-1,EN61204-3, light industry level, criteria A

OTHERS

MTBF

584K hrs min. MIL-HDBK-217F (25 )℃

DIMENSION

22.5*90*100mm (W*H*D)

PACKING

0.17Kg; 72pcs/13.2Kg/0.91CUFT

NOTE

1. All parameters NOT Specially mentioned are measured at 230VAC input, rated load and 25 °C of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor

3. Tolerance: includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets

EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies. “ ” ”

5. Length of set up time is measured at cold first start. Turning ON/OFF power supply may lead to increase to the set up time.