Vocopro CLUB-8800 Manual


Læs gratis den danske manual til Vocopro CLUB-8800 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Vocopro CLUB-8800, eller vil du spørge andre brugere om produktet?

Side 1/4
Club 8800
Quick Reference Setup Guide
This quick reference guide is provided to help you set up your CLUB-
8800 system for the first time. It contains instructions on setting up
the products that are included in the
CLUB-8800. If you are connect-
ing any additional gear that is not included in the
CLUB-8800, refer to
the appropriate manuals for detailed instructions.
The first step to putting together your new CLUB system is unpacking all of the necessary equipment. Remember to keep
your manuals nearby when setting up, as you may need to reference them. The products listed below are included in the
CLUB-8800 system:
Mounting components into the CLUB-8800
Follow these basic guidelines when mounting:
Always screw in the mounting screws using an
“X” formation.
If possible, to keep the products cooler, leave some
space in between the components in the rack.
CDG 9000 PRO CONTROLLER
UHF 5800
VSP M1
KJ 7800 PRO
CDG 9000 PRO PLAYER
VP 2100
Below is one way to configure your CLUB-8800:
CDG-9000PRO
(2) RCA cables
(2) Control interface connector
wires
(1) Instruction manual
KJM-7800PRO
(1) Instruction manual
VP-2100PRO
(1) Instruction manual
VX-15 Speakers
(4) VX-15 speakers
UHF-5800
(1) 3 ft. male/male ¼” cable
VSP-M1 Multi-Effect Digital Signal
Processor/Mixer
(1) Instruction manual
SS-88 Speaker Stand
(4) SS-88 speaker stands
Road Case
(1) CLUB-8 road case
(1) Rolling cart
• (2) MK 38PRO microphones
(1) Gooseneck DJ light
(1) Double RCA to ¼” cable (3’3”)
Rack-mounting screws
On the web at www.vocopro.com
or call toll free 1-800-678-5348
Setup each speaker stand by extending the support lefts to SS-88
a position that is stable and tighten the tension mechanism firmly.
Place a speaker on top of the so that the shaft of the VX-15 SS-88
SS-88 VX-15 fits flush into the mounting cavity on the bottom of the .
NOTE: Each end of the pole has a particular diameter fitted SS-88
for common speakers’ mounting cavities. If the shaft does SS-88
NOT fit flush into the mounting cavity on the , loosen the VX-15 SS-
88 pole and reverse it in the stand and then remount the speaker.
Repeat the above steps for each speaker and stand.
Be sure that each product has a power cord firmly attached. It is
recommended that you use a power strip/surge protector when con-
necting your to a power outlet.CLUB-8800
Connecting Power
Setting up the speakers and speaker stands
VX-15 Speaker
SS-88 Stand
Once you have mounted all of the components into the , it is time CLUB-8800
to connect them. Follow these directions on connecting the components.
NOTE: If you are also connecting components that are not part of the CLUB-
8800 system, please refer to the manual of that product for setup instruc-
tions.
Connect the Control Interface Connector from the corresponding “CONNECT TO MAIN UNIT” jack on the rear panel of the
remote unit to the “CONNECT TO REMOTE CONTROL” jack on the rear panel of the player unit.
CDG-9000PRO remote unit to the player unit.
Connecting the components
CDG 9000 Player
CDG 9000 Controller
1
1.
2.
3.
MAKE SURE ALL PRODUCTS ARE POWERED OFF
PRIOR TO CONNECTING TO AN AC OUTLET.


Produkt Specifikationer

Mærke: Vocopro
Kategori: Ikke kategoriseret
Model: CLUB-8800

Har du brug for hjælp?

Hvis du har brug for hjælp til Vocopro CLUB-8800 stil et spørgsmål nedenfor, og andre brugere vil svare dig