Waring Commercial BB900G Manual

Waring Commercial Blender BB900G

Læs gratis den danske manual til Waring Commercial BB900G (4 sider) i kategorien Blender. Denne vejledning er vurderet som hjælpsom af 62 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 31.5 anmeldelser. Har du et spørgsmål om Waring Commercial BB900G, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should

always be followed including the following:

READ ALL INSTRUCTIONS.

2. To protect against electrical hazards, do not immerse the blender

base in water or other liquid.

3. Close supervision is necessary when any appliance is used by or

near children.

4. Unplug from outlet when not in use, before putting on or taking off

parts, and before cleaning.

5. Avoid contacting moving parts.

6. Do not operate any appliance with a damaged cord or plug or

after the appliance malfunctions or is dropped or damaged in any

manner. Return appliance to the nearest authorized service facility for

examination, repair or electrical or mechanical adjustment.

7. The use of attachments including canning jars not recommended by

the appliance manufacturer may cause hazards.

8. Do not use outdoors.

9. Do not let cord hang over edge of table or counter, or touch hot

surfaces.

10. Keep hands and utensils out of container while blending to prevent

the possibility of severe personal injury and/or damage to the

blender. A rubber scraper may be used but must be used only

when the blender is not running.

11. Blades are sharp. Handle carefully.

12. If your blender utilizes a removable jar base and blade assembly, to

avoid injury never place cutting assembly cutting blades on base

without container properly attached.

13. Always operate blender with cover in place.

14. When blending hot liquids, remove center piece of two-piece cover

on those units supplied with this construction. See Hot Blending

Instructions

SAVE THESE INSTRUCTIONS

Service

Refer to the list of Authorized Service Centers enclosed with your

Waring blender for the name of the nearest Service Center, or

Write to:

Waring Factory Service Center

314 Ella T. Grasso Ave.

Torrington, CT 06790

(800) 269-6640

Ship blenders for repair to the above address or to an Authorized

Service Center. Do not ship to a Waring Sales Ofce.

Note: If your application involves the processing of biologically

active materials we request that any items returned for service

be sterilized before being shipped. Such items must be clearly

identied as having been sterilized both by a tag on the item itself

and by a statement in the accompanying correspondence. Waring

will not accept delivery of any returns unless they are so identied.

Replacement parts for your own “Out of Warranty” repairs are

obtainable at the above address.

WARRANTY

Waring warrants every new WARING COMMERCIAL BLENDER to be free from

defects in material and workmanship for a period of one year from the date of

purchase when used with foodstuffs, non-abrasive liquids (other than detergents)

and non-abrasive semi-liquids, providing it has not been subject to loads in excess

of the indicated rating.

Under this warranty, the Waring Commercial Division will repair or replace any part

which, upon our examination, is defective in materials or workmanship, provided the

product is delivered prepaid to the Waring Service Center at Torrington, CT 06790,

or any Factory Approved Service Center.

This warranty does not: a) apply to any product which has become worn, defective,

damaged or broken due to use or due to repairs or servicing by other than the

Waring Service Center or a Factory Approved Service Center or due to abuse,

misuse, overloading or tampering; b) cover consequential damages of any kind.

This warranty gives you specic legal right, and you may have other rights which

vary from state to state so that certain limitations or exclusions set forth above may

not apply to you.

WARNING: This warranty is VOID if appliance is used on Direct Current (D.C.) or if

the appliance has not been registered.

WARING COMMERCIAL

314 Ella T. Grasso Ave.

Torrington, CT 06790

www.waringproducts.com

BLENDER

OPERATION MANUAL

10WC116188

004589 RV19 1010

Operation

This piece of equipment is designed for the high speed blending,

pulping, mixing or reducing of animal tissue, vegetables, foodstuffs,

plant materials and other substances. A typical operating sequence is

as follows:

1. Add materials to be processed to container.

2. Place cover on container.

3. With the power switch on OFF position, place container on

blender. Be sure container is fully seated and the drive coupling

is properly engaged.

4. Set power switch to ON, Low or High position.

5. When nished processing, set power switch to OFF position.

6. Allow motor to come to a complete stop before removing

container from blender.

Note: Containers with removable bottoms have left-handed threads.

To tighten, turn in direction of molded arrow on underside of removable

bottom. When reassembling, be sure rubber gasket is positioned

between the container and the ange on the blade assembly.

Important

HOT BLENDING INSTRUCTIONS

To minimize possibility of scalding when blending hot materials, the

following precautions and procedures must be observed.

1. Limit amount of material processed to 1/2 pint.

2. Completely remove the center portion of the two-piece container

lid before starting motor. (This will allow venting of the rapidly

heated and expanding air present inside container when blender

is running.)

3. Always start blending lowest speed setting, then progress to

desired speed.

4. Never stand directly over blender when it is being started or while

it is running.

To Operate Timer Model Only

Blender

One Quart Capacity Speciﬁcations

•Ratings 120VAC–50/60Hz–SinglePhase

 230VAC–50Hz–SinglePhase

•Motors Permanentlylubricatedseries-wounduniversaltype

•Timer Selectivetimercyclefrom1to180secondsfor

automatic continuous running

•Bases Zincdiecastingwithepoxyenamelnishorpolished

stainless steel

•Containers Stainlesssteel,borosilicateglass,polycarbonateor

san plastic

•Cord 6foot–18gauge–threeconductorgroundedcordwith

strain relief

•ULListed 120modelsonly

Grounding Instructions

• Foryourprotection,WaringCommercialBlendersareequippedwitha

3-conductor cordset.

• 120Voltunitsaresuppliedwithamolded3-pronggrounding-typeplugand

should be used in combination with a properly connected grounding-type

outlet

If a grounding-type outlet is not available, an adapter, shown in Figure 2, may

be obtained to enable a 2-slot wall outlet to be used with a 3-prong plug.

Referring to Figure 3, the adapter must be grounded by attaching its

grounding lug under the screw of the outlet cover plate.

Caution: Before using an adapter, it must be determined that the outlet cover

plate screw is properly grounded. If in doubt, consult a licensed electrician.

Never use an adapter unless you are sure it is properly grounded.

Note: Use of an adapter is not permitted in Canada.

Green/Yellow: Earth Ground Blue: Neutral Brown: Live

Produkt Specifikationer

Mærke:	Waring Commercial
Kategori:	Blender
Model:	BB900G

Har du brug for hjælp?

Hvis du har brug for hjælp til Waring Commercial BB900G stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blender Waring Commercial Manualer

Waring Commercial Torq 2.0 TBB160 Manual

29 December 2024

Waring Commercial Torq 2.0 TBB145 Manual

29 December 2024

Waring Commercial Blade BB340 Manual

29 December 2024

Waring Commercial Blade BB320 Manual

29 December 2024

Waring Commercial Blade BB300 Manual

29 December 2024

Waring Commercial 700G Manual

29 December 2024

Waring Commercial NuBlend BB185 Manual

29 December 2024

Waring Commercial BB160S Manual

29 December 2024

Waring Commercial Blade Series 1 BB320S Manual

29 December 2024

Waring Commercial BB900G Manual

1 September 2024

Blender Manualer

Nyeste Blender Manualer

Aiwa Saberu Pro ATB-3000 Manual

1 Oktober 2025

ElectriQ iQMix-Platinum Manual

30 September 2025

Aiwa Saberu 2500 ATB-2500 Manual

29 September 2025

Aiwa Saberu 1500 ATB-1500 Manual

29 September 2025

Brentwood JBS-1000BK Manual

29 September 2025

Aiwa Saberu 1800 ATB-1800 Manual

28 September 2025

Aiwa Saberu 600 ATB-600 Manual

28 September 2025

Brentwood JBS-500BK Manual

28 September 2025

Aiwa Saberu 1000 ATB-1000 Manual

28 September 2025

MPM CMBL-02 Manual

28 September 2025