Whirlpool AKZ 431 WH Manual

Whirlpool Ovne AKZ 431 WH

Læs gratis den danske manual til Whirlpool AKZ 431 WH (3 sider) i kategorien Ovne. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Whirlpool AKZ 431 WH, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

INSTALLING THE BUILT-IN /

UNDERCOUNTER COLUMN OVEN

Recommendations

Important: Disconnect the oven from the

mains before carrying out any installation

work or servicing.

•Installation must be carried out by a qualified

technician in accordance with the manufacturer's

instructions and in compliance with local regulations.

•Unpack the oven and make sure that the

appliance has not been damaged during transport

and that the oven door closes properly. If you

are not sure contact the dealer or the

nearest service centre.

•After removing the oven from its packaging,

leave it on the polystyrene base to prevent it

from being damaged.

•When installing the oven it is advisable to wear

protective gloves.

•Do not lift the oven by the door handle. Get hold

of it using the side openings provided.

Preparing the housing unit

•Kitchen units in contact with the oven must be

heat resistant (80 °C min).

•Cut the kitchen unit to fit before installing the

appliance. Carefully remove any shavings or

sawdust that could prevent the appliance from

running properly.

•The dimensions of the oven and unit are shown

in figures 1-2-3.

•To allow for proper ventilation, an opening

should be left at the bottom of the kitchen unit.

Pay attention to the dimensions in the diagram.

When installation has been completed, the

bottom of the oven must be inaccessible.

•When installing, make sure that the sides of the oven

do not touch the adjacent kitchen units (fig. 4-5).

•When installing ovens under the worktop, leave

a minimum clearance of 5 mm between the

upper edge of the oven and the lower edge of the

worktop (fig. 6). In order for the appliance to

operate properly, this clearance must never

be obstructed.

•If the kitchen unit is not securely fixed to the wall,

it must be anchored with standard brackets (G)

(fig. 7) available on the market.

Electrical connection

Regulations require that the appliance be

earthed.

•Connection to the mains must be carried out by a

qualified electrician in accordance with the

manufacturer’s instructions and in compliance

with local regulations.

•The installer is responsible for connecting

appliances correctly to the mains and for

observing the safety regulations.

•The oven power cable must be long enough to

connect the built-in appliance to the mains.

•Observance of safety directives requires that a

multi pole switch with a minimum contact gap of

3 mm be used for the installation.

•Do not use multiple plug adapters or extension

leads.

•After the oven has been installed, the electrical

components must be inaccessible.

Connecting the oven to the power

supply

•Make sure that the voltage indicated on the rating

plate is the same as the mains voltage. The rating

plate is on the front edge of the oven (visible

when the door is open).

•If the oven does not have a power supply cable

proceed as follows:

1. Remove the two fastening screws of the

terminal box cover located on the bottom part

of the oven’s rear covering.

2. Remove the cover to gain access to the terminal

box and insert the power cable (see table)

through the opening located on the bottom of

the oven.

3. Connect the cable to the terminal box, tighten

the screws as far as they will go and secure it to

the cable fastener.

4. Put the cover back on by inserting the two

blades in the slots and fasten it with the two

screws.

Securing the oven

•Lift the oven getting hold of it by the openings on

the sides and insert it into the housing unit, being

careful not to trap the power supply cable (fig. 8).

•Center the oven in the housing unit before

securing it.

•Make sure that the plastic spacers (if provided)

are positioned correctly in the fastening holes.

Then anchor the oven to the housing unit with

the screws provided.

Power supply cable table

N° of conductors Type of cable

1N+ ~H05 RR-F 3 X 1.5 mm²

2+ ~H05 RR-F 3 X 1.5 mm²

(Switzerland only)

10200150aGB.fm Page 2 Monday, September 5, 2005 2:43 PM

Fig. 1

Fig. 2

Fig. 3

Produkt Specifikationer

Mærke:	Whirlpool
Kategori:	Ovne
Model:	AKZ 431 WH

Har du brug for hjælp?

Hvis du har brug for hjælp til Whirlpool AKZ 431 WH stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ovne Whirlpool Manualer

Whirlpool AKZM 6560/IXL Manual

6 Oktober 2022

Whirlpool AKZM 8910/IXL Manual

6 Oktober 2022

Whirlpool AKP 311 AV Manual

6 Oktober 2022

Whirlpool AKP 371/IX Manual

6 Oktober 2022

Whirlpool AKP 533/IX Manual

6 Oktober 2022

Whirlpool AKZ 471 IX Manual

6 Oktober 2022

Whirlpool W11 OM1 4MS2 P Manual

6 Oktober 2022

Whirlpool W7 OS4 4S1 H Manual

6 Oktober 2022

Whirlpool W11 OS1 4S2 P Manual

6 Oktober 2022

Whirlpool AKZM 775/IXL Manual

6 Oktober 2022

Ovne Manualer

Nyeste Ovne Manualer

BlueStar RNB364GV2 Fornuis Manual

15 Januar 2025

PKM EH4-50GK5M Fornuis Manual

15 Januar 2025

Bosch HBG237YS0R Oven Manual

15 Januar 2025

Indesit K642 Fornuis Manual

15 Januar 2025

Hotpoint HUI612 K Fornuis Manual

15 Januar 2025

BEKO FSM52020DWD Fornuis Manual

15 Januar 2025

GE JBP80WF1WW Fornuis Manual

15 Januar 2025

White And Brown MF 20 Oven Manual

15 Januar 2025

GE JT950CA3CC Oven Manual

15 Januar 2025

Zanussi-Electrolux ZKC6020X Fornuis Manual

15 Januar 2025