Xerox WorkCentre XD130 Manual
Læs gratis den danske manual til Xerox WorkCentre XD130 (61 sider) i kategorien Printer. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Xerox WorkCentre XD130, eller vil du spørge andre brugere om produktet?
Side 1/61
701P33177
User Guide
W ork tC ne r XD Seriese
FCC Compliance in the USA
WARNING: This equipment has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a different circuit than the
receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not specifically approved by the
Xerox Corporation may void the authority granted by the FCC to operate
this equipment.
Shielded cables must be used with this equipment to maintain compliance
with FCC regulations.
ENERGY STAR
As an ENERGY STAR® Partner, Xerox Corporation
has determined that this product meets the ENERGY
STAR® guidelines for energy efficiency.
© 2/1999 by Xerox Corporation. All rights reserved.
Copyright protection claimed includes all forms and matters of copyrighted
material and information now allowed by statutory or judicial law or
hereinafter granted, including without limitation material generated from the
software programs that are displayed on the screen such as icons, screen
display looks, etc.
XEROX®, The Document Company®, and the stylized X are registered
trademarks of Xerox Corporation and Xerox Canada Ltd. is a licensee of all
the trademarks.
Product names used in this guide may be trademarks or registered
trademarks of their respective companies and hereby acknowledged.
ENERGY STAR is a U.S. registered mark.
Information
To get answers for any other questions you might have regarding your
WorkCentre, to register your warranty by phone, or for assistance with the
installation of your WorkCentre you may call:
1 – 800 – TEAM – XRX (1 – 800 – 832 – 6979)
Supplies
To order supplies for your WorkCentre, call or visit your local retailer or visit
their Web site. If your store does not stock these items, you may call the
following number.
In the United States and Canada:
Xerox SupplyNet toll free at: 1 – 800 – 822 – 2200
Toner Cartridge: 6R914
Drum Cartridge: 13R551
Service
A Customer Service Support Representative will assist you in keeping your
WorkCentre operational and, if required, will arrange for service. Call our
experts at:
1 – 800 – TEAM – XRX (1 – 800 – 832 – 6979)
The following information will be needed when you call Xerox:
Machine Type: XD _______________________
Machine serial number: __ __ __ and the __ __ __ __ __ __.
(Product Code) (Serial number)
The serial number is located on the back cover of the WorkCentre, to the
left of the power cord.
Xerox Corporation
Rochester, New York
Manufactured in Japan
XEROX
Visit the Xerox Web site at: http://www.teamxrx.com
PRODUCT CODE : V8Y
RATING : 120 V-60 hz
A W
MANUFACTURED : SSK
1998 APRIL
000000
Product code
Serial Number
Information
How to obtain a French User Guide
Au Canada et aux États-Unis, pour obtenir la version française du présent
guide d´utilisation, veuillez composer:
1 – 800 – TEAM – XRX (1 – 800 – 832 – 6979)
À l´extérieur des États-Unis et du Canada, veuillez communiquer avec
votre représentant Xerox.
It's Illegal
In the USA
It is against US law to copy copyrighted material without permission of the
copyright owner unless the copying falls within the "Fair Use" or library
reproduction rights of the copyright law. Further information on these U.S.
provisions may be obtained from the Copyright Office, Library of Congress,
Washington, D.C. 20550, or telephone the Copyright Office at (202) 707-
9100 and ask for circular 21. Copying of other items may be prohibited. If
you have any questions, seek legal advice.
In Canada
In Canada it is against the law to copy copyrighted material without
permission of the copyright owner, unless the copying falls within the
private study, research or criticism provision of the copyright law. Copying
of other items may be prohibited. If you have any questions, seek legal
advice.
i
Table of Contents
Servicing Your WorkCentre ..................................................................... iv
Ordering Supplies ..................................................................................... iv
Safety Notes................................................................................................ 1
Helpful Hints ............................................................................................... 4
Getting to Know Your WorkCentre........................................................... 5
Installation .................................................................................................. 6
Control Panel............................................................................................ 10
Power Reduction / Auto Clear................................................................. 12
Auto Copy Function................................................................................. 12
Paper Specifications................................................................................ 13
Loading Paper.................................................................................... 14
Flashing .............................................................................................. 15
Making Copies on the Document Glass ................................................ 16
Making Copies on the Single Pass Feeder
(XD103f/ 105f/ 120f/ 125f) ......................................................................... 17
Making Copies on the Automatic Document Feeder(XD130df/155df). 18
Manual Two-Sided Copying (XD130df/155df only) ............................... 20
Image Quality............................................................................................ 21
Reduction/Enlargement........................................................................... 22
Copying Oversized Documents.............................................................. 23
Book Mode (XD104 only)......................................................................... 23
Paper Tray Bypass (XD100/102/103f/120f/125/125f only)...................... 24
Alternate Paper Tray (XD104/105f/130df/155df only) ............................ 25
Two-Sided Copying (for all models except the 130df/155df) ............... 26
Envelopes ................................................................................................. 27
ii
Table of Contents
Customizing Your WorkCentre............................................................... 28
Programmable Features......................................................................... 28
Programmable Feature Settings 0 – 9 and 11 – 18................................ 32
Programmable Feature Setting 10 ......................................................... 33
WorkCentre Care...................................................................................... 34
Cleaning the Document Glass and Cover .............................................. 34
Cleaning the Corotron Wire.................................................................... 34
Single Pass Feeder Misfeed/Automatic Document Feeder... 35
– E2 Clearing the Paper Path .......................................................... 36
Toner Cartridge Replacement ...................................................... 39
J2 Drum Cartridge Replacement.................................................... 40
Counter access......................................................................................... 41
Total copies/prints remaining on the drum cartridge .............................. 41
Printer Driver Software Installation........................................................ 42
WorkCentre XD Properties (Printer Driver)............................................ 44
Displaying the Driver Properties dialog from an application ................... 44
Displaying the Properties dialog from the Start Menu ............................ 45
Displaying the Properties dialog from the Xerox Printer Services Program
(Status Monitor) ...................................................................................... 45
Properties Tabs ...................................................................................... 46
On-Line Help........................................................................................... 46
?
?
?
?? Printer Driver Help (Windows 95/98 and NT) ................................... 46
iii
Table of Contents
Creating WorkCentre XD Floppy Disk Installation Diskettes............... 47
Enabling High Speed Printer Communications .................................... 48
Problem Solving....................................................................................... 49
Problem Solving Chart............................................................................ 49
Status Code Chart .................................................................................. 51
Printing Solution Chart............................................................................ 52
Technical Data.......................................................................................... 55
iv
Servicing Your WorkCentre
In the USA and Canada
Should you be unable to resolve a problem after using the Problem Solving
section of this manual, place a call to the Xerox Customer Support Center
at:
1 – 800 – TEAM – XRX
(1 – 800 – 832 – 6979)
The Customer Support Representative can solve many problems over the
phone. Please have the following information available before calling:
– The WorkCentre model number: XD _________
(on the control panel)
– The serial number ________________________
(Located on the back cover of the WorkCentre to the left of the
power supply.)
–The purchase date from your purchase receipt (required for warranty
service).
–A description of the problem.
– Status Code (if any) displayed on the control panel.
Ordering Supplies
To order supplies for your WorkCentre, call or visit your local retailer. If
your store does not stock these items, you may call:
Xerox SupplyNet toll free at:
1 – 800 – 822 – 2200
Toner Cartridge – 6R914
Drum Cartridge –13R551
1
Safety Notes
Your WorkCentre and supplies have been designed and tested to meet
strict safety requirements. These include safety agency examination and
approval, and compliance to established environmental standards. Please
read the following instructions carefully before operating the WorkCentre
and refer to them as needed to ensure the continued safe operation of your
WorkCentre.
Follow all warnings and instructions marked on or supplied with the
product.
Symbology: = High Voltage, = Heated Surface, ! = Warning
= Laser Caution use of controls or adjustments or performance of
procedures other than those specified herein may result in hazardous
radiation exposure.
Unplug this WorkCentre from the wall outlet before cleaning. Always use
materials specifically designated for this WorkCentre. Use of other
materials may result in poor performance and could create a hazardous
situation.
Do not use aerosol cleaners. Follow the instructions in this User Guide for
proper cleaning methods.
Never use supplies or cleaning materials for purposes other than what they
were intended. Keep all supplies and materials out of reach of children.
Do not use this WorkCentre near water, wet locations, or outdoors.
Do not place this WorkCentre on an unstable cart, stand, or table. The
WorkCentre may fall, causing personal injury or serious damage to the
WorkCentre.
This product is equipped with a 3-wire grounding type plug (e.g., a plug
having a third grounding pin). This plug will fit only into a grounding-type
power outlet. This is a safety feature. To avoid risk of electric shock,
contact your electrician to replace the receptacle if you are unable to insert
the plug into the outlet. Never use a grounding adapter plug to connect the
WorkCentre to a power source receptacle that lacks a ground connection
terminal.
2
Safety Notes
This WorkCentre should be operated from the type of power source
indicated on the marking label. If you are not sure of the type of power
available, consult your local power company.
Do not allow anything to rest on the power cord. Do not locate the
WorkCentre where persons will step on the cord.
The power supply cord is the disconnect device for this equipment.
Insure that installation is near the outlet and is easily accessible.
Your machine is equipped with an energy saving device to conserve
power when the machine is not in use. The machine may be left on
continuously.
Slots and Openings in the cabinet and in the back and sides of the
WorkCentre are provided for ventilation. To ensure reliable operation of
the WorkCentre and to protect it from overheating, these openings must
not be blocked or covered. The WorkCentre should never be located near
or over a radiator or heat register. This WorkCentre should not be placed
in a built-in installation unless proper ventilation is provided.
Never push objects of any kind into the slots of the WorkCentre as they
may touch dangerous voltage points or short out parts which could result in
a fire or electric shock.
Never spill liquid of any kind on the WorkCentre.
Never remove covers or guards that require a tool for removal. There are
no casual operator serviceable areas within these covers.
Never defeat interlock switches. Machines are designed to restrict
operator access to unsafe areas. Covers, guards, and interlock switches
are provided to ensure that the machine will not operate with covers
opened.
Use of an extension cord with this WorkCentre is not recommended
or authorized.
Avoid direct viewing of the document lights. The lamps are bright and,
while not harmful, they may cause an annoying afterimage. Always keep
the document cover closed during operation and storage.
Avoid exposing the drum cartridge to light for extended periods of time.
3
Safety Notes
Do not touch the green photoreceptor. Scratches or smudges that appear
on the photoreceptor will result in poor copy quality and may shorten the
service life.
Do not put your hands into the fuser area, as you may be burned.
Ozone: This product produces ozone during normal operation. The ozone
produced is dependent on copy volume and is heavier than air. Providing
the correct environmental parameter, as specified in the Xerox installation
procedures, ensure that concentration levels meet safe limits.
If you need additional safety information concerning the WorkCentre or
Xerox supplied materials, you may call the following toll-free number.
In the United States or Canada: 1 – 800 – 828 – 6571
4
Helpful Hints
Care of your WorkCentre
• Do not place heavy objects on any surface of the WorkCentre.
• Take care not to place liquids on or near the WorkCentre.
• Avoid placing clips or staples on any WorkCentre surface.
Maintenance
• Clean the Document Glass daily and as required.
• Do not apply cleaning liquids or sprays directly to the WorkCentre;
apply to the cloth first.
• Store paper in a dry area, on a flat surface, and in a closed cabinet.
• Wrap partially-used reams of paper tightly.
WorkCentre location
For reliable WorkCentre operation and copy quality, Xerox
recommends:
• Place your WorkCentre in a well-ventilated room.
• Recommended environment:
– Temperature: 50° to 90°F / 10° to 32°C.
– Humidity: 20% to 85%.
• Place the WorkCentre on a flat, level surface.
• Avoid locations that subject the WorkCentre to:
– Direct sunlight.
– Extreme changes in temperature or humidity.
5
Getting to Know Your WorkCentre
Document glass
Front cover
Control panel
Exit tray
Paper tray 1
Document cover
Release
latch
Alternate paper tray
XD104/ 105f/ 130df/
155df only
Exit tray
Serial number
Parallel port Lift area
Power switch
Power connection
Paper
guides
Paper tray bypass
paper guides
Side cover
Original exit
area Original feeder tray
Original guides
SPF XD103f/ 105f/ 120f/125f
ADF XD130df/ 155df only
Paper tray 2
XD120f/130df/
155df only
6
Installation
As you unpack the WorkCentre, familiarize yourself with its contents. After
the WorkCentre is installed, and the Ready Indicator is lit, the WorkCentre
is ready to make copies.
IMPORTANT: Save the carton and packing materials. They should be
used to repack the WorkCentre if it has to be shipped for servicing or in
case you move.
* Note: To ensure reliability of the WorkCentre use the IEEE-1284
compliant parallel cable that is supplied with the machine. Only cables
labeled “IEEE-1284” can be used with your WorkCentre.
Drum cartridge
(installed in the
machine)
Packing material
Power cord
Starter toner
cartridge
IEEE-1284
Parallel Cable *
User documentation/
Installation CD
7
Installation (continued)
Follow the steps below to properly set up your Xerox WorkCentre.
AD
CE
B
1. Remove the bag from the WorkCentre.
2. Remove the pieces of tape A, B, C, D,
and the packing material E.
XD130df/155df copier only
Remove the tape and the packing material
supporting the clear plastic 2-sided tray.
XD130df/155df copier only
To ensure the 2-sided tray is in the correct
position, gently push it in the direction
shown by the arrow.
3. Open the document cover and remove
the packing materials shown.
4. Unscrew and remove the shipping
screw from the left side of the
WorkCentre.
CAUTION: The WorkCentre will
malfunction if the shipping screw is not
removed.
5. Lift and pull open the paper tray. Turn
and remove the paper tray button.
CAUTION: Paper will misfeed if the paper
tray button is not removed.
For the XD 120f/ 130df/ 155df copier
only
Note: Be sure to remove the pressure
plate lock from both paper trays.
8
Installation (continued)
6. Secure the paper tray button and the
shipping screw in the locations shown.
• Turn the paper tray button to secure
its storage position.
Note: Save the paper tray button and the
shipping screw. They will be needed if the
WorkCentre has to be moved.
7. Load paper into the tray.
• Refer to the Loading Paper section
for additional information.
• Do not fill above the max line.
8. Push the paper tray firmly back into the
WorkCentre.
Note: Ensure that the alternate paper tray
is lowered (XD 104/ 130df/ 155df only).
9. Press the release lever to open the side
cover.
10. Remove the Caution tape from the
cover.
11. Remove the two red fuser pins by
pulling the string upward one at a time.
• Discard the fuser pins.
Note: Misfeeds will occur if the fuser pins
are not removed.
CAUTION: Ensure that the side cover is
always open before opening the front
cover.
12. Press the front cover release buttons to
open the front cover.
9
Installation (continued)
13. Remove the starter toner cartridge from
the silver bag. Vigorously shake the
cartridge to loosen the toner.
• Thoroughly shaking the cartridge will
assure maximum copies per
cartridge.
• Xerox has included a Starter Toner
Cartridge. Purchased replacement
toner cartridges will yield
approximately three times the
number of copies.
14. Remove the toner cartridge cover.
1
23
15. Slide the toner cartridge into the
WorkCentre until it locks into place.
16. Close the front cover and the side
cover.
Skip to the Printer Driver Software
Installation section in this User Guide to
set up the WorkCentre XD for printing.
17. Plug the power cord into the
WorkCentre and then into a grounded
outlet.
18. Turn on the power switch. In
approximately two seconds the ready
indicator will light. Copying is now
possible.
Note: Save the carton and packing
materials. They should be used to repack
the WorkCentre if it has to be shipped for
servicing or moved.
11
Control Panel
7. Variable Percentage: Press the down key to thedecrease
percentage. Press the up key to increase the percentage. Any
percentage from 50% to 200% may be selected.
8. %: Press this key to display the reduction/enlargement percentage
selected.
9. Display Window: Copy quantity, reduction/enlargement settings, and
status codes appear in this area.
10. Quantity Keys: Select up to 100 copies. Press the 1 key to increase
the quantity by one. Press the key to increase the quantity by 10.10
• To display the number of copies requested during the copy run press
the 10 key.
• Press the Clear key to clear the selected quantity.
11. WorkCentre Diagram: Helps you locate areas that require your
attention. The indicators will flash in the area requiring attention. For
additional information refer to the Problem Solving section.
12. Paper Supply Selection (XD104/ 105f/ 120f/ 130df/ 155df only):
Press to change the selected paper supply. The selected paper supply
location will be indicated by a green light on the WorkCentre diagram.
13. SPF/ADF Misfeed Indicator: This indicator will light when a misfeed
occurs in the SPF or the ADF.
14. On-line/Off-line Key: Press this button to alternate between On-line
and Off-line status. When the light is lit, the printer is On-line.
15. Ready Indicator: When the light is ON (not flashing), the WorkCentre
is ready to make copies. When the light is flashing after the Start key
is pressed, the WorkCentre is warming up and the copy cycle will begin
automatically.
16. Start: Press this key to begin copying.
• The display will change to 1 and increases by 1 as each copy is
made.
17. Clear/Stop: Press this key to stop the WorkCentre while making
copies or to clear copy quantity. If the key is pressed twice quickly, all
programming will be cleared.
12
Power Reduction / Auto Clear
Power Reduction Modes automatically reduce power consumed by the
WorkCentre when the WorkCentre has not been used for a set period of
time. There are two modes of power reduction; Power Save, and Power
Shut-off.
Power Save Mode – The Ready Indicator will flash and the other indicators
will remain on. To copy from the Power Save mode select the desired
features and press Start. The copies will be made automatically.
Power Shut-Off Mode – When the WorkCentre enters the power shut-off
mode the Ready Indicator will flash and the other indicators will turn off. To
copy from the power shut-off mode, press the Start button, then, select the
desired features and press Start again. The copies will be made
automatically.
Auto Clear – This WorkCentre is enabled at the factory to return to the
Normal Copy Mode approximately one minute after a job is completed.
Unless otherwise programmed, the Normal copy Mode settings are as
follows:
• Copy Quality – Auto
• Copy Lighter/Darker – Normal
• Priority Tray – Tray 1
• Priority Magnification – 100%
• Quantity Selected – 1
Note: Time periods for the Power Shut-Off, Power Save, and Auto Clear
modes can be modified to meet your specific copying needs. Refer to
Customizing Your WorkCentre section of this User Guide for information
about changing these settings.
Auto Copy Function
This function provides the ability to program a copy job while the copier is
warming up, or to pause a print job to enable copying.
1. Program the copy job.
2. Press Start.
• The current page will be completed if printing is in process.
3. When the copy job is completed, press the On-line/Off-line button to
immediately return to the print job.
13
Paper Specifications
Paper Storage
Note: Paper affected by humidity, and curled paper can cause jams and
copy quality problems.
For reliable copier operation and good copy quality, Xerox recommends
that paper be stored:
• on a flat surface.
• in a closed container.
• in a low humidity area.
• tightly wrapped, if the ream is partially used.
The Specifications Chart below provides information about the types of
paper that can be used at each of the paper input areas.
Paper Input Paper Tray 1 and 2 Alternate Paper Tray/
Paper Tray Bypass
Paper Sizes 5.5×8.5" to 8.5×14" /
A5 to 216×356mm
3.5×5.5" to 8.5×14" /
A6 to 216×356mm
Paper Weights
Optimum
Range
20 lb / 80 gsm
15 – 24 lb /
56 – 90 gsm
20 lb / 80 gsm
14 – 34 lb /
52 – 130 gsm
Paper Capacities
Copy, letterhead, and
predrilled
XD100/125/125f
XD102/103f
XD104/105f
XD120f
XD130df/ 155df
20 lb / 80 gsm
250 sheets
200 sheets
250 sheets
2×250 sheets
2×250 sheets
20 lb / 80 gsm
single sheet
single sheet
multi-sheet
single sheet
multi-sheet
Labels, Envelopes,
and Transparencies *
No Yes (1 at a time)
* Use labels, envelopes, and transparencies specifically designed for
copiers and laser printers (high temperatures).
14
Loading Paper
will flash in the copy quantity display and the green indicator in the
copier diagram will flash when:
• a paper tray is empty.
• paper misfeeds: paper has not fed all the way into the copier.
• a paper tray is not closed properly.
If the paper has misfed, open the paper tray indicated by the flashing green
light on the copier diagram and remove the misfed paper.
• Do not reuse the misfed paper.
• Ensure that the paper is under the corner snubbers.
• Close the paper tray.
• If copying, press the Start key to make the remaining copies.
• If printing, the job will automatically resume when paper is added.
1. Lift and pull open the paper tray.
2. Push down on the pressure plate until it
locks in position.
Note: The procedures for loading paper
into tray 1 and tray 2 are identical.
3. Adjust the paper guides to the desired
paper size.
• Squeeze the side guide.
• Lift and insert the rear guide.
• When adding paper larger than
8.5×11/A4, remove the rear guide
and store it in the pocket in front of
the side guide.
15
Loading Paper
4. Fan the paper and insert it into the tray.
• Ensure that the paper corners are
under the corner snubbers.
• Do not fill above the max fill line.
5. Close the paper tray.
6. If copying, press Start to continue. If
printing, the job will automatically
resume.
• To cancel the flashing P without
restarting copying, press the Clear
button.
Flashing
When the Alternate Paper Tray runs out of paper, or the paper misfeeds,
the P will flash in the display and the green indicator in the copier diagram
will flash.
Alternate Paper Tray (XD104/ 105f/ 130df/ 155df only)
1. Add paper if the Alternate Paper Tray is
empty.
2. If paper has misfed, remove it by
carefully pulling the edge of the paper in
the direction of the arrow.
3. If copying, press the Start key to
continue.
If printing, press the On-line/Off-line key
to continue.
16
Making Copies on the Document Glass
78%
Au to
86%
100%
129%
200% Max
50% 200%
DO
CUMENT
10 1
W
o
rkCe
n t r
e
C
1. Ensure that the WorkCentre is Off-line.
• The light between the two icons will
be off.
2. Select the desired copy features from
the control panel.
3. Select the number of copies.
• Press the 10 to increase the quantity
by 10. Press the 1 key to increase
the quantity by 1.
• To clear the selected quantity, press
the Clear key.
4. Lift the Document Cover.
5. Place the original face down and align
it with the registration guide on the
document glass.
6. Close the Document Cover.
Note: Leaving the cover open while
copying will affect copy quality and toner
consumption.
7. Press Start to begin copying.
• The number in the display window
returns to 1 and advances as each
copy is made.
17
Making Copies on the Single Pass Feeder (XD103f/
105f/ 120f/ 125f)
Use the Single Pass Feeder(SPF) to make one collated copy of originals.
The SPF holds up to 30 originals (20 lb/80 gsm) in one job. Ensure
originals are in good condition, and that all staples and paper clips have
been removed. Use the document glass to make copies from
transparencies, facsimile paper, or originals having other unusual
characteristics. For reliable copying operation, use originals within the
following ranges:
Paper weight range: 16 to 24 lb/60 to 90 gsm
Paper size range: 5.5×8.5"/A5, 8.5×11"/A4 and 8.5×14"/216×353 mm
The SPF comes from the factory with the Auto Start feature enabled. Refer
to Customizing Your Copier section of this User Guide for information
about changing this setting.
78%
Au to
86%
100%
129%
200% Max
50% 200%
DO
CUMENT
10 1
W
o
rkCe
n t r
e
C
1. Select the required paper tray.
2. Select the desired copy features from
the control panel.
• The maximum copy quantity is 1.
Reinsert the originals into the SPF for
each set required.
3. Adjust the paper guide to the original
size.
Note: Writing that is very close to the
leading or trailing edge of the original may
not copy. Turning the original around in
the SPF may help.
4. Insert up to 30 originals face up into the
SPF until the green SPF light on the
copier diagram comes on.
18
Making Copies on the Automatic Document
Feeder (XD130df/155df)
The Automatic Document Feeder (ADF) allows you to automatically make
single sided or two-sided copies. The ADF holds up to 30 originals
(20 lb/80 gsm). Ensure originals are in good condition, and that all staples
and paper clips have been removed. Use the document glass to make
copies from transparencies, facsimile paper, or originals having other
unusual characteristics. For reliable copying operation, use originals within
the following ranges:
Paper weight range: 16 to 24 lb/60 to 90 gsm
Paper size range: 5.5×8.5"/A5 (Short Edge feed only)
8.5×11"/A4 and 8.5×14"/216×353 mm
The ADF comes from the factory with the Auto Start feature disabled.
Refer to Customizing Your WorkCentre section of this User Guide for
information about changing this setting.
Note: Automatic two-sided copying is available only in the copying mode,
not the print mode.
The available copy options are:
Icon Original Copy Max
Quantity
(2!1) Two-sided Single sided 100 sets
(2!2) Two-sided Two-sided 1 set
(1!2) Single sided Two-sided 1 set
(1!1) Single sided Single sided 100 sets
Single sided original to single sided copies (1!
!!
!1)
This mode will create single sided copies from your originals.
1. Place the originals face up in the ADF.
2. Select the icon (1 to 1) and any additional features
and the desired quantity.
3. Press Start to begin copying.
The WorkCentre will produce the requested number of
uncollated (1,1,1…2,2,2…3,3,3…) single sided sets.
19
Making Copies on the Automatic Document
Feeder (XD130df/155df)
Single sided originals to two-sided copies (1!
!!
!2)
This mode will create two-sided copies from your single sided
originals.
1. Place the originals face up in the ADF.
2. Select the icon (1 to 2) and any additional
features.
• The maximum copy quantity is 1. Reinsert the originals
into the ADF for each set required.
3. Press Start to begin copying.
The WorkCentre will produce one set of two-sided copies.
Two-sided originals to two-sided copies (2!!!!2)
This mode will create two-sided copies from your two-sided
originals.
1. Place the originals face up in the ADF.
2. Select the icon (2 to 2) and any additional features.
• The maximum copy quantity is 1. Reinsert the originals
into the ADF for each set required.
3. Press Start to begin copying.
The WorkCentre will produce one set of two-sided copies.
Two-sided originals to single sided copies (2!!!!1)
This mode will create single sided copies from your two-sided
originals.
1. Place the originals face up in the ADF.
2. Select the icon (2 to 1) and any additional features
and the desired quantity.
3. Press Start to begin copying.
The WorkCentre will produce the number of uncollated single
sided sets that you requested.
20
Manual Two-Sided Copying (XD130df/155df only)
Important Tip: The WorkCentre has been configured to copy onto
8.5×11/A4 paper. When copying onto any other paper size the image may
not be placed properly. The default paper size for both paper trays is
8.5×11/A4.
You may want to change the default setting for one or both of the trays if
you find the factory settings do not meet your needs. Refer to
Customizing Your WorkCentre for information about changing the default
paper size.
Xerox
1
1. Place side 1 original face down on
the Document Glass, with the TOP
toward the . Lower theLEFT
document cover.
Note: 16 lb / 60 gsm copy paper is not
recommended for two-sided copying.
2. Select the desired 1-Sided/2-Sided
mode.
3. Select the quantity.
4. Press Start to make side 1 copies.
• After scanning side 1, the light next
to the selected mode will flash to let
you know that the WorkCentre is
ready to scan side two.
Xerox
2
5. Remove the side 1 original and place
the side 2 original face down on the
Document Glass with the TOP toward
the LEFT. Lower the document
cover.
6. Press Start.
21
Image Quality
The image quality features described on this page can be used to improve
copies of documents printed on colored paper, photographs, or are of poor
quality.
Auto
Auto: Use Auto when copying from originals with a colored
background or mixed text and graphics.
Note: When Auto is selected, the copier automatically varies the
contrast of your copies. Lighter/Darker settings are not available.
Text: Use Text to copy documents containing mostly text.
Photo: Use Photo when the originals are photographs.
Toner Save: Toner Save mode lowers overall copy density on each
page. This feature can be used when making draft copies.
Copy Contrast
You can vary the copy contrast of your
copies in small increments when Text,
Photo, or Toner Save settings are
selected.
Note: When Auto is selected the copy
contrast settings are not available.
Press the copy contrast key to lighten or
darken copies while in the Text, Photo, or
Toner Save settings.
There are 5 contrast settings represented by 3 indicator lights. The
indicators light up one or two at a time to represent the selected setting.
Successive pushes of the key will change the indicators in successive
order. Darkest, normal and lightest settings are depicted by one indicator.
When 2 indicators are lit, the copy contrast will be mid point between the
darker setting and the lighter setting.
Toner
S
ave
Photo
Auto
Text
22
Reduction/Enlargement
Preset Reduction/Enlargement
Press the Preset Reduction/Enlargement
key to quickly select one of the 6 preset
percentages. The customer settable
percentage ( ) has been set at the
factory for 50%. Refer to Customizing
Your WorkCentre for information about
changing the default percentage.
50% 200%
DOCU
MENT
10
Wo
rkCent
re
88
Variable Percentage
Press the Variable Percentage key to
increase or decrease the reduction or
enlargement by 1% increments. You may
select any percentage from 50 – 200%.
Press the % key to display the current
percentage. When any reduction or
enlargement is selected the variable
percent indicator will light.
50% 200%
DOCU
MENT
10 1
Wo
rkCent
re
Display Window
Preset or variable reduction/enlargement
percentages appear in the Display Window
at the time selections are made. After a
few seconds, the reduction/enlargement
percent is replaced with the number of
copies selected. Press the % key to recall
the current reduction/enlargement ratio.
Reduction/Enlargement Reference Table
Original Size Copy Size % To Use
5.5 × 8.5 8.5 × 14 154%
5.5 × 8.5 8.5 × 11 129%
8.5 × 14 8.5 × 11 78%
8.5 × 11 5.5 × 8.5 64%
A4 A3 141%
B4 A4 81%
A4/ A3 A5/ A4 71%
Produkt Specifikationer
| Mærke: | Xerox |
| Kategori: | Printer |
| Model: | WorkCentre XD130 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Xerox WorkCentre XD130 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Printer Xerox Manualer
29 December 2024
29 December 2024
13 December 2024
13 December 2024
13 December 2024
13 December 2024
14 Oktober 2024
9 Oktober 2024
30 September 2024
23 September 2024
Printer Manualer
- CSL
- Velleman
- Lenovo
- Fujifilm
- Testo
- EC Line
- OKI
- Sawgrass
- Ibm
- Datamax-O'neil
- Evolis
- Orient Technologies
- Star
- Dell
- Royal Sovereign
Nyeste Printer Manualer
25 Juni 2025
23 Juni 2025
23 Juni 2025
23 Juni 2025
22 Juni 2025
22 Juni 2025
22 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025