XO UIM1585NOASS Manual
XO
Isterningmaskine
UIM1585NOASS
Læs nedenfor 📖 manual på dansk for XO UIM1585NOASS (32 sider) i kategorien Isterningmaskine. Denne guide var nyttig for 32 personer og blev bedømt med 4.9 stjerner i gennemsnit af 16.5 brugere
Side 1/32
I worked really hard
on this manual -
so please read it...
UNDERCOUNTER NUGGET ICE MAKERS
MODELS:
XOUIMN1585NO, XOUIMN1585NOP
XOUIMN1585NOA, XOUIMN1585NOPA
2
REGISTRATION HELPS YOU BY -
5
STANDARD HEIGHT
XOUIM 15 5 & XOUIM 15 5 PN 8 NO N 8 NO
ADA HEIGHT
XOUIMN1585NOA & XOUIMN1585NOPA
2
these are the models
covered in this
book
take a minute to circle your model above
and record your serial number
here in case you need it later
INDOOR NUGGET
GOURMET ICE MAKER
7
Serious injury, fire or death...
Okay -
8
When installing, remember you need
to leave ready access to both the power
Cut access to an adjoining cabinet to
locate outlet and water there.
a perfect fit
install under counter
ALL XO UNDERCOUNTER
UNITS A E E-WIREDRRIV PR
WITH LOW P E PLUGSROFIL
FOR EASY INSTALLATION
4"
(100mm)
7"
(178mm)
15”
WH E N IN S TAL L ING W ITH
TH E H INGE SIDE NEXT TO A WA LL -
LEAV DE ATE SPACE FOR E A QU
YOUR DOOR HANDLE
DOOR HAS THE ABILITY TO OPEN TO 115
(381mm)
MINIMUM
Standard Height Units
33-3/4” MINIMUM
(853mm)
ADA Height Units
31-7/8” MINIMUM
(808mm)
Clearance
Gap
90°
Door Swing
WALL
9
a perfect fit
your xo is this big ( )or small, as the case would be
XOUIMN1585__ & XOUIMN1585__A ICE MAKER
33-
STANDARD HEIGHT
(853mm)
31-13/16”
STANDARD HEIGHT
(808mm)
9/16”
W
H
height & width
depth
22-25/32”
(579mm)
D
THE OVERALL DEPTH SHOWN (22-25/32”) INCLUDES THE DOOR WITH 3/4” PANEL.
THE DEPTH OF THE ICE MAKER CABINET ONLY IS 20-13/32”
14-15/16” WIDE
(379mm)
TOP VIEW
115
90
11
All water contains some impurities and minerals.
Your XO Ice Maker is designed to produce chewable, nugget ice. It does this by compressing
ice flakes as they are forming.
PURER WATER YIELDS PURER ICE.
Cubes are formed by cold water spraying against a chilled mold. Pure water freezes faster
than water containing impurities. The spraying action causes the cubes to be built up in layers
as the pure water freezes more quickly and the water containing impurities is washed away by
the spray and falls into the water bin to be diluted and drained away.
The ice maker uses an auger system to take the ice as it is forming in flakes and compresses
them, capturing air in the process to form soft, chewable nuggets of ice.
Periodic maintenance is required to ensure that your ice maker is performing at its best.
See the maintenance section of this book and the Maintenance Schedule.
FILTERS AND WATER TREAMENT
The correct filter is always recommended. It has the ability to remove odors as well as
particulate from water prior to reaching the ice maker.
(consult www.xoappliance.com for more information on which filter is right for you)
Water softeners exchange one mineral for another (salt) which can cause inferior ice quality
such as soft, mushy ice that clumps together. If you are using a water softener, you should
install a bypass to supply untreated water to the ice maker.
Water produced by Reverse Osmosis and deionized water are not recommended. It is more
corrosive than tap water and can cause harm to the equipment over time.
water quality
12
Plan the arrangement of the water supply pipes. You will need both a water supply line and
a drain (see section on installing a gravity drain unit or pump drain unit)
If the tap water has a high level of minerals, an inline filter will be required.
Attach the water supply line to the rear of the unit
with flexible tube to the fitting indicated here.
The tubing must be long enough to permit the
unit to be pulled out for service.
Water supply should be between 20psi and 80psi.
Attach the drain to the connection indicated here
If you are installing an XOUIMN1585NO unit with a
gravity drain, the line must be pitched down
1/4” per ft to ensure correct drainage.
If the drain is positioned at a higher elevation than
the connection on the rear of the unit, a pump
will be required. Use model XOUIMN1586NOP.
This unit comes with a pre-installed drain pump
capable on discharging to a drain up to 8’ above
the unit.
IMPORTANT: The keep drains as short and straight
as possible for optimal performance.
The electric power, water supply pipeline and drain pipeline must be in compliance with all
provisions under the local laws and building regulations.
IMPORTANT: The product is designed for use in a fixed condition but it may be required to
pull the product out for service. Therefore, do not install any material at the front, upper or
lower end of the product which may be an obstacle when pulling the product out.
Once the unit is in place, use the leveling legs to ensure the unit is level.
Each side should have at least 1/16" of space for projection of the screw head near the bottom.
the plumbing
1/4” O.D.
DRAIN
WATER
SUPPLY
13
INSTALLING THE XOUIMN1585 without a drain pump.
Position the ice maker in front of the opening. Level the unit using the leveling legs.
Wash and flush the water supply tube and connect the unit to the cold water isolation valve.
Prepare the drain. The drain must be pitched downward at a drop of 1/4” per foot to drain properly.
Horizontal runs of 5’ or more must be anchored to a wall for support to prevent sagging.
A sanitary trap and air gap must be installed in the line prior to entering the home’s drain system.
The trap prevents sewer gas from flowing back to the ice maker.
The air gap device prevents siphoning drain water back into the ice maker.
Cut the 5/8” ID drain hose (not supplied) to the required length. Immerse the hose in warm water to make
installation easie
hose to the drain using hose clamps.
r, then using a threaded hose barb connection sealed with teflon tape, connect the drain
Turn the water supply on and check to ensure there are no leaks.
If there are no leaks, plug the unit into the electrical outlet.
Press the switch to the “ICE” position. The compressor will run approximately 3 - 5 minutes.
Slide the unit back into it’s final position and recheck to ensure it is level.
REMEMBER to adhere to all local building codes and regulations
with gravity drain
DRAIN VENT
THE DRAIN POINT
MUST BE LOWER
THAN THE DRAIN
OUTLET OF THE
ICE MAKER
AI
DEVICE
R GAP
SANITARY TRAP
If you purchase a gravity drain unit
and find you need one with a pump
the XOUIMN1585 can easily be
retrofitted with one in the field.
Simply order a XOUIMPUMP from
www.xoappliance.com
14
INSTALLING THE XOUIM1565SP with DRAIN PUMP.
Position the ice maker in front of the opening.
Level the unit using the leveling legs.
Wash and flush the water supply tube and connect the unit to the cold water isolation valve.
Cut the 3/8” diameter drain hose to the required length. Immerse the hose in warm water to make
installation easie
(9’ of 3/8” ID drain hose is included with pump models)
r, then connect the drain hose to the drain using hose clamps.
IMPORTANT: Check local codes to determine if an air gap is required between the drain and the pump.
Turn the water supply on and check to ensure there are no leaks.
If there are no leaks, plug the unit into the electrical outlet.
Fill the ice container with clean tap water approximately 3/4 full. The drain pump should turn on and pump
the water out. Check again for leakage.
Press the switch to the “ICE” position. The compressor will run approximately 3 - 5 minutes.
Fill the ice container to 3/4 full once more. Block the drain tube while the pump is running.
The pump should continue to run.
Slide the unit back into it’s final position and re-check to ensure it is level.
REMEMBER to adhere to all local building codes and regulations
with drain pump
DRAIN VENT
THE DRAIN POINT
MAY BE HIGHER
THAN THE DRAIN
OUTLET OF THE
ICE MAKER
SANITARY TRAP
AIR GAP DEVICE
16
installing the door panel
The panel is held in place by self tapping screws and/or machine screws.
To install your panel, follow these simple steps:
1. First prepare your custom panel.
The panel must be 14-7/8” wide and no more than 3/4” thick. It cannot weigh more than 20 lbs.
The height of the panel can vary but cannot block the free exchange of air through the toekick.
If you are using one of the optional Stainless Steel door panels (XOUIMN15S or XOUIMN15ADA)
it is ready to install out of the box, simply peel off the protective layer of plastic before installing.
2. If your cabinetry uses a handle, locate and attach it before mounting the panel. Remember to
recess the screw heads.
2. If installing a custom panel, clamp the panel in position on the open door being careful not to
damage the panel or door liner. Use the 14 self tapping screws provided to secure the panel
as outlined on the exploded diagram shown on the next page. Check the screw depth if your
panel is less than 3/4” thick to ensure the screw points do not protrude through the panel.
If using one of the optional Stainless Steel door panels, using the machine screws provided,
secure the panel with the 14 machine screws supplied as outlined on the exploded diagram
shown on the next page.
3. Install Hole Covers as required and remove the clamps.
AFTER INSTALLATION UNDERCOUNTER DOOR MUST BE ABLE TO OPEN 90
o
overlay panel dimensions xouimn1585no & xouimn1585nop
14-7/8"
(378mm)
FRONT
TOP
18
ouimn1585noada & xouimn1585nopadax
Standard Height
29-13/32”
(747mm)
ADA Height
27-5/8”
(702mm)
PANEL HEIGHTS ARE MINIMUMS, PANEL MAY BE TALLER.
PANEL MUST NOT INTERFERE WITH TOEKICK VENTS.
21
operation
You XO Ice Maker is simple to operate.
When you open the door you will see
the electronic button/display located at
the top center of the appliance.
The first button, , allows you to cycle through the 5 differentLAMP
interior LED Light colors (white, Dark Blue, Green, Red and Light Blue).
The light will always come on first when the unit is switched on.ICE
Initially, the unit will automatically fill and drain water three times then,
the ice making cycle will begin.
The light will come on to indicate there is a problem with NO WATER
the water s pply.u
The light will come on when the drain valve is open.DRAIN
INITIAL OPERATION:
When you open the door, located at
the bottom, right of the face of the
unit is a three position toggle switch.
The center position is OFF.
The top position is ICE.
The bottom position is WASH.
Turn the appliance to ICE, this will start the ice making process.
Always discard the first batch of ice. Good quality ice is produced in
1-2 hours.
23
maintenance
Proper maintenance, cleaning and santizing is essential to ensure your
ice is safe, fresh and odor free.
WASH FEATURE:
Regular maintenance is the key to delicious, wholesome ice.
The WASH feature helps make this easy to perform.
When the ASH Position of the switch is ected, the ng cess W sel cleani pro
takes approximately 10 minutes and the following action take place:
BEFORE BEGINNING - REMOVE ALL ICE FROM THE ICE BIN.
1. Water is supplied to the first water tank and the auger operates for
5 minutes.
NOTE: You may optionally cleaning solution (see CLEANING)add
to the ice outlet.
2. After Step 1 is complete, drain and re-fill with water.
3. Operate the Auger for 1 minute.
4. Repeat Steps 2 and 3, twice more for a total of 3 times.
5. Drain and stop the product. When restarting follow the procedures
for an initial start, discarding the first batch of ice.
Produkt Specifikationer
| Mærke: | XO |
| Kategori: | Isterningmaskine |
| Model: | UIM1585NOASS |
Har du brug for hjælp?
Hvis du har brug for hjælp til XO UIM1585NOASS stil et spørgsmål nedenfor, og andre brugere vil svare dig
Isterningmaskine XO Manualer
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
Isterningmaskine Manualer
- Isterningmaskine Innoliving
- Isterningmaskine Emerio
- Isterningmaskine Scotsman
- Isterningmaskine CDA
- Isterningmaskine Whirlpool
- Isterningmaskine Domo
- Isterningmaskine Bartscher
- Isterningmaskine Hendi
- Isterningmaskine Bomann
- Isterningmaskine Livoo
- Isterningmaskine GE
- Isterningmaskine U-Line
- Isterningmaskine Heinner
- Isterningmaskine Trebs
- Isterningmaskine Manitowoc
Nyeste Isterningmaskine Manualer
21 Februar 2025
20 Februar 2025
15 Februar 2025
14 December 2024
24 November 2024
24 November 2024
4 November 2024
22 Oktober 2024
22 Oktober 2024
28 September 2024