Yamaha SPS-10MM Manual

Yamaha Hi-Fi system SPS-10MM

Læs gratis den danske manual til Yamaha SPS-10MM (2 sider) i kategorien Hi-Fi system. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 20 anmeldelser. Har du et spørgsmål om Yamaha SPS-10MM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

ASSEMBLY

INSTRUCTIONS

Read this before use

SPEAKER STAND

SPS-10MM

Thank you for selecting the Yamaha SPS-10MM speaker stand.

●This speaker stand is only for the speaker systems

listed in “USABLE SPEAKERS” below. Do not use the

speakers other than these listed.

●To prevent the speaker from falling, use the screws

and parts provided with the stand.

●To prevent the speaker stand from falling over, select

a location which is flat and stable.

●To avoid accidents resulting from tripping over loose

speaker cables and to prevent the speaker stand from

falling over, fix the speaker cables to the wall, etc.

●Do not let the children lean on the stand as this might

cause the serious accidents resulting from the falling

over of the speaker stand.

●To prevent the speaker stand from discoloring and

warping, keep the speaker stand away from the

stoves and places where it will be exposed to direct

sunlight, etc.

●Do not attempt to clean the speaker stand with

chemical solvents as this might damage the finish.

Use a clean, dry cloth.

●Secure placement or installation is the owner’s

responsibility. YAMAHA shall not be liable for any

accident caused by improper placement or

installation of speakers.

PRECAUTIONS

618–868 (24-5/16”–34-3/16”)

282

(11-1/8”)

(2-1/2”)

(13/16”)

(3-3/16”)

300

(11-13/16”)

300

(11-13/16”)

(2-3/8”)

DIMENSIONS (mm/inch)

Top view

Front view

SPECIFICATIONS

Dimensions (W x H x D) : 300 x 618 – 868 x 300mm

(11-13/16” x 24-5/16

– 34-3/16” x 11-13/16”)

Weight : 1.6 kg (3 lbs. 8 oz.)

USABLE SPEAKERS

●NS-10MM

●NS-10MMT

●NX-220P

(the main and rear speakers included in the NS-P220

speaker package)

●NS-E104

(the rear speakers included in the NS-P320 speaker

package)

●NS-E114

(the rear speakers included in the NS-P326 speaker

package)

●NX-S100S

(the front and rear speakers included in the DVX-S100

sound system)

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Japan V816800-1

●ASSEMBLY FIGURE

ASSEMBLY PROCEDURES

Before beginning assembly, check the parts list and make sure all the parts are included.

●ASSEMBLY PROCEDURES

(You will need a screwdriver for assembly.)

1. Attaching the base and support.

Pass the support through the hole from the bottom of the base,

and fasten the + self-binding tapping screws 1.

●Fix the support so that the holes for the screws comes to the

rear side.

●Do not overtighten the + self-binding tapping screws 1.

Doing so may damage the screws or assembly.

2. Attaching the pole and support.

Insert the pole to the support, and fasten the hexagon socket

set screws into the three hole on the support using the2

included wrench 5.

●The line on the pole shows the limit of the stand height. Do

not use the stand pulling out the pole above from this line.

The hexagon socket set screw of the lower side becomes2

ineffective and the fixation becomes unstable.

3. Attaching the pads.

Put the pads 4to the four corners on the bottom of the base to

prevent the stand from moving rickety.

4. Attaching the gaskets.

Put the gaskets to the both side of the plate.6

5. Wiring the speaker cables.

Insert the speaker cables to the hole on the plate, and aligned

them to the grooved part on the bottom of the base.

6. Attaching the speakers.

Line up the holes on the bottom of the speaker and the center

hole on the plate, and fasten the + binding screws 3.

●In order to ensure that the speakers do not fall, always hold

the speakers while attaching the speakers.

●PARTS LIST

NAME PARTS NOS.

QUANTITY

1+ self-binding tapping screws EP040090 12

(4 x 12)

2Hexagon socket set screws VV249400 7

3+ self-binding screws (4 x 8) EG340360 4

4Pads VV249200 8

5Wrench (hexagonal) VV249500 1

6Gaskets VV249300 4

Speaker

cable

Pole

Limit of the stand

height

Plate

Support

Base

Produkt Specifikationer

Mærke:	Yamaha
Kategori:	Hi-Fi system
Model:	SPS-10MM

Har du brug for hjælp?

Hvis du har brug for hjælp til Yamaha SPS-10MM stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Hi-Fi system Yamaha Manualer

Yamaha CD-C603 Manual

10 August 2025

Yamaha MCR-332 Manual

31 December 2025

Yamaha MusicCast SRT-1500 Manual

6 Oktober 2024

Yamaha R-N1000A Manual

21 August 2024

Yamaha MusicCast NP-S303 Manual

20 August 2024

Yamaha R-N800A Manual

20 August 2024

Yamaha R-N2000A Manual

3 August 2024

Yamaha CRX-E300 Manual

31 Juli 2024

Yamaha CRX-E200 Manual

30 Juli 2024

Yamaha MCR-N570 Manual

21 Juli 2024

Hi-Fi system Manualer

Nyeste Hi-Fi system Manualer

Elta 2444MP3 Manual

14 September 2025

Meridian F80 Manual

14 September 2025

Panasonic SC-PM91D Manual

13 September 2025

Samsung DA-E550 Manual

12 September 2025

Aiwa MSBTU-700DAB Manual

12 September 2025

JK Audio AutoHybrid IP2 Manual

11 September 2025

Shure MVX2U Manual

10 September 2025

Lynx AES16 Manual

10 September 2025

Medion P85444 (MD 89295) Manual

9 September 2025

Reflexion HIF1937 Manual

8 September 2025