ZTE MF80 Manual

ZTE Mobiltelefon MF80

Læs gratis den danske manual til ZTE MF80 (4 sider) i kategorien Mobiltelefon. Denne vejledning er vurderet som hjælpsom af 55 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 28 anmeldelser. Har du et spørgsmål om ZTE MF80, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
ZTE CORPORATION
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057 Tel: +86-755-26779999
URL: http://www.zte.com.cn E-mail: mobile@zte.com.cn
ZTE MF80
Quick Guide
Operate system Windows 7, Windows Vista(32bit or 64bit),
Windows XP (SP2 or later), MAC (10.4 or later)
Web Browser
IE (7.0 or later), Firefox (2.0 or later), Opera (10.0
or later), Safari (4.0 or later), Chrome (5.0 or
later)
Operating temperature 0°C ~ +40°C
Storage temperature -20°C ~ +50°C
Charging temperature 0°C ~ +45°C
Humidity 5%~ 95%
Notes: microSD is a trademark of SD Card Association.
The device’s standby and working time are only for your reference, and
based on ideal working environment.
Getting to Know Your Device
The following gure shows the appearance of the device, it is only for your
reference. The actual device may be different.
1
2
3
4
5
7
6
Right Side Front Left Side
Interface and Buttons
1. External Antenna
Connector
It is used to connect an external antenna to enhance
the signal strength.
2. Power Hold the button to switch on/off the device.Power
3. Connect
• Press it to connect to the Internet or disconnect
from the Internet.
• Hold it for more than 3 seconds to switch the
WAN Connection Mode between A(Always on) or
M(Manual).
4. WPS
This button is used to start/end Wi-Fi Protected Setup
authentication process and enable/disable the Wi-Fi
function.
• Hold it for more than 3 seconds to activate the WPS
function.
• Press it to enable/disable Wi-Fi function.
5. LED Screen It indicates the signal type, signal strength, battery, Wi-
Fi, etc.
6. Memory card slot
(microSD card) It is where you insert the memory card (microSD card).
7. Charger/USB
port
• Charge your device.
• Connect the client to your device via USB cable.
Notes:
Hold the and buttons simultaneously until the LED screen turns WPS Power
off, and then release the buttons. The device will restart automatically and
restore to the factory default settings.
LED Indicator
When the device is powered on, the following icons will appear on the LED
screen, with the corresponding indicates listed in the table below:
Icon Indication
Network signal strength.
Network type. 2G or 3G icon will appear on the LED
screen according to the network being connected.
Connect to the Internet automatically.
Connect to the Internet manually.
Roaming network indication.
New message received.
Wi-Fi Status and number of the connecting users.
Battery power indication.
Hardware Installation
Inserting SIM Card and Battery
1. Slide the battery cover, and remove it.
2. Insert the SIM card into the SIM card holder.
3. Insert the battery as shown with the contacts located against the metal
springs, and press the battery down into the case.
1
2
4. Put the battery cover of the modem atly upon the body of device. Direct
the battery cover towards the locking catches on the sides of the device,
and then push the battery cover to lock the cover into its place.
Inserting microSD Card
1. Pull the microSD cover out of the card slot.
Notes:
Do not pull the cover rudely, as it is connected with the device.
2. Insert the microSD card into the microSD slot. The following picture
shows the correct inserting direction. You will hear a click when the
microSD card locks in place.
3. Close the microSD cover.
Switching On/Off Your Device
Hold the button to switch on/off the device.Power
Notes:
The device is powered on when the LED screen lights up.
Charging Your Device
You can charge your device by using USB cable or adapter.
1. Insert the charger lead carefully with the plug arrow facing the bottom of
the device.
2. The plug only ts one way. Do not use excessive force to insert the plug.
3. Make sure the plug is the right way round and lined up correctly and
insert it gently.
Working Mode
Your device supports three working modes. For the client, we only use PC or
laptop as the example in this document.
USB Mode: Connect to the device with the USB cable.
Wi-Fi Mode: Connect to the device via Wi-Fi.
Mixed Mode: Connect to the device with the above two connection methods.
Notes:
If you want to connect to the Internet by using Wi-Fi mode, make sure that
the client supports the Wi-Fi function.
The following picture is the application example. All of the client devices can
surf on the Internet at the same time.
LEGAL INFORMATION
Copyright © 2011 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted, reproduced, translated or utilized in
any form or by any means, electronic or mechanical, including photocopying and
microlm, without the prior written permission of ZTE Corporation.
The manual is published by ZTE Corporation. We reserve the right to make
modications on print errors or update specications without prior notice.
Version No. : R1.0
Establish a connection between your device and
the client
Via USB Cable
1. Connect your device and the client with the USB cable.
2. Power on your device.
3. Follow the system prompts to complete the software installation.
Notes:
• If the system does not launch installation automatically, you can run the
installation program in path of .My Computer > Mobile Hotspot
• The driver of your device will be installed at the same time.
4. After the installation, the system will create a shortcut icon on your
desktop and a program group in the Start→Programs menu. The
connection between your device and the client will be established
successfully a moment later.
Via Wi-Fi
1. Power on your device directly. It will take 1~2 minutes to initialize.
2. Use your normal Wi-Fi application on the client to search the available
wireless network.
Notes:
You need to check your Wireless Network Connection. Set the client
to obtain an IP address automatically in the Internet protocol (TCP/IP)
properties, and the client will get an IP address like “192.168.0.100”.
3. Select the SSID of your device, and then click .Connect
Introduction
ZTE MF80 is a 3G/2G mobile hotspot device, working in GSM/GPRS/
EDGE/WCDMA/HSPA/HSPA+ network. The client devices could connect to
it via USB or Wi-Fi interface. The device supports data and SMS services,
enabling you to communicate anytime and anywhere.
This quick guide provides instructions on how to install and get started with
the product. For information about connection of services, please consult
your service provider.
Specication
Data Service
HSPA+: DL 42Mbps
HSUPA: UL 5.76Mbps
WCDMA CS: 64kbps UL/DL
WCDMA PS: 384kbps UL/DL
Interface USB and Wi-Fi
Wi-Fi Standard 802.11b/g
Wi-Fi Security WEP/WPA/WPA2
USB Version USB 2.0 HIGH SPEED
USB Interface Type Micro USB
Weight 97g
Dimensions (W×H×D): 102mm*53mm*16.6mm
microSD card Support up to 32GB microSD card
Power Adapter 5V/1.5A
Battery 1900mAh
*Standby time 100hours
*Working time 4.5hours
123456789

Produkt Specifikationer

Mærke: ZTE
Kategori: Mobiltelefon
Model: MF80

Har du brug for hjælp?

Hvis du har brug for hjælp til ZTE MF80 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Mobiltelefon ZTE Manualer

ZTE

ZTE Blade A3 Joy Manual

19 Oktober 2025
ZTE

ZTE S512 Manual

18 Oktober 2025
ZTE

ZTE Z957 Manual

18 Oktober 2025
ZTE

ZTE Chorus Cricket Manual

18 Oktober 2025
ZTE

ZTE Vodafone 520 Manual

18 Oktober 2025
ZTE

ZTE Blade L9 Manual

18 Oktober 2025
ZTE

ZTE Blade 10 Prime Manual

18 Oktober 2025
ZTE

ZTE Whirl Manual

7 Juli 2025
ZTE

ZTE Cymbal U Manual

7 Juli 2025
ZTE

ZTE Link III Manual

6 Juli 2025

Mobiltelefon Manualer

Nyeste Mobiltelefon Manualer

Asus

Asus MyPal A686 Manual

5 November 2025
Asus

Asus MyPal A730 Manual

4 November 2025
NGM

NGM Tango 1 Manual

19 Oktober 2025
NGM

NGM Pico Manual

19 Oktober 2025
NGM

NGM Prestige Manual

19 Oktober 2025
Realme

Realme RMX3231 Manual

4 Oktober 2025
Realme

Realme C35 Manual

3 Oktober 2025
Realme

Realme C67 5G Manual

3 Oktober 2025
Amplicom

Amplicom PowerTel M6750 Manual

29 September 2025
Amplicom

Amplicom PowerTel M9500 Manual

27 September 2025