2hp Swarm Manual

2hp Ikke kategoriseret Swarm

Læs gratis den danske manual til 2hp Swarm (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 20 anmeldelser. Har du et spørgsmål om 2hp Swarm, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

2hp Swarm

Swarm

OUT

DETUNE

VOICES

FREQ

2hp

Hyper Oscillator

Discover more at https://www.twohp.com/modules/swarm

Voices CV Input

Range: -5V to +5V

Voices

Controls the number of active

oscillators. Only 1 oscillator is

active when the knob is fully

counter clockwise.

20 oscillators are active when

the knob is at the center posi-

tion. From there, the number

of active oscillators increments

to dozens of oscillators (max of

88 for Saw, 55 for Pulse) when

the knob is fully clockwise. Detune

Controls the amount detune

applied to each oscillator. The

rst half of the knob provides

tasteful detune, while the

second half provides chaotic

detune.

No detune is applied when

the knob is fully counter

clockwise.

Detune CV Input

Range: -5V to +5V

Freq

1V/Oct Input

Range: -5V to +5V

Freq

Controls the macro pitch of all

active voices. Tracks 1v/oct.

Audio Output

Range: 10Vpp

Tech Specs

Width: 2HP

Depth: 45mm

Power Consumption:

+12V=85mA, -12V=7mA,

+5V=0mA

Wave Toggle

Toggles between sawtooth

(left) and pulse (right)

waveforms.

Watch The Demo

Module Installation

• To install your 2hp module, locate a space with the appropriate HP in your rack for instal-

lation.

• Next, connect the module’s power cable to your power supply. The cables on this end are

keyed, though you should make sure to align the red stripes on both connectors to en-

sure safe and proper connection. Our illustration uses a ying bus cable, though the same

action applies for busboards/alternate power solutions. See the gure below for refer-

ence:

• Next, make sure your module’s power cable is properly connected to your module. For

2hp modules, conrm that your cable’s red stripe aligns with the white marker line on

the module’s PCB, just above the power header. You may notice that even though there

is only 1 row of 5 pins on your 2hp module, but 2 rows on the power cable. You can use

either row of 5 pin connectors on the cable with your module, so long as the red stripe is

properly aligned. See gure below for reference:

• Finally, mount your module to the rails

using 2.5mm mounting screws and the

included sliding mounting nuts. Your

module is now ready to be powered on and

patched!

Produkt Specifikationer

Mærke:	2hp
Kategori:	Ikke kategoriseret
Model:	Swarm

Har du brug for hjælp?

Hvis du har brug for hjælp til 2hp Swarm stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret 2hp Manualer

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Simrad Active Imaging HD (Thru-Hull) Manual

14 Juni 2025

Garritan Harps Manual

14 Juni 2025

Marshall CV-H20-HF Manual

14 Juni 2025

Aiphone IXW-MAA Manual

14 Juni 2025

Rival HM-743 Manual

14 Juni 2025

Lutec Avony Manual

14 Juni 2025

Giordani G-SAFE & PLAY Manual

14 Juni 2025

Gourmia GAF799 Manual

14 Juni 2025

Arendo 307503 Manual

14 Juni 2025

Hughes & Kettner Tube 100 Manual

14 Juni 2025