ABB DY365 4CE Manual

ABB Ikke kategoriseret DY365 4CE

Læs gratis den danske manual til ABB DY365 4CE (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om ABB DY365 4CE, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

User manual

DY365 4CE REMOTE ACTUATOR

Read all instructions carefully

• The DY365 4CE remote actuator is a four-relay electronic device that receives the command signals

from the switch via DY365 I/O extension ports.

It performs actions of 1B type and is intended to operate in a domestic and similar environment

with overvoltage category III and normal pollution degree (EN 60730-1).

SAFETY WARNINGS

During product installation and operation it is necessary to observe the following

instructions:

1) The device must be installed by a qualiﬁed person

2) Before accessing the terminals, make sure that the leads are not live

3) Do not power the device if any part of it is damaged

4) Connect the product following the diagrams described in this manual

5) In the electrical system upstream of the device must be installed a switch and a

protection device against the overcurrents.

6) The product must be installed and activated in compliance with current electric

systems standards.

7) After installation inaccessibility to the terminals without using dedicated tools

must be guaranteed.

Code Model Description

2CSM221181R1000 DY365 4CE 4-channel remote actuator

TECHNICAL FEATURES

• Power supply: 12/24 V AC/DC (-15%/+10%) 50/60 Hz

• 4 relays normally open 8A / 250 V AC

• I/O extension port for connection to the switchDY365

• Operating temperature: 0 ÷ +50 °C

• Storage temperature: -25 ÷ +70 °C

• Container: 4 DIN modules

• Protection degree: IP20 (IP40 when correctly installed in the electrical panel)

OPERATION

• When switched on, the red LEDs emit 2 ﬂashes lasting half a second (switch-on sequence).

• Once the switch-on sequence is completed, the green LED is lit to indicate normal device

operation and the red LEDs are turned on/off to indicate the corresponding status of the

4 channels (on = ON).

Channels conﬁguration

• During normal operation, press and hold the SET button for at least 3 seconds to enter

in conﬁguration mode. In this mode the green LED is off while the red LED

corresponding to the relay to be conﬁgured ﬂashes.

• To select the relay to be associated with the channel of DY365 switch , press the SET

button until the red LED for the relay to be conﬁgured ﬂashes.

• Once the channel is selected, the actuator remains in conﬁguration mode for 60 seconds:

activate the channel conﬁguration on the DY365 switch.

To activate the channel conﬁguration, see the DY365 switch user manual.

• Once the relay conﬁguration is complete, the actuator resumes normal operation

• To cancel the conﬁguration of a channel, enter the conﬁguration mode, select the channel

with the SET button (relative red LED ﬂashing), then press the SET button for at least three

seconds until the green LED lights up again.

Each new conﬁguration cancels the previous conﬁguration

REFERENCE STANDARDS

Compliance with Community Directives:

2014/35/EU (LVD)

2014/30/EU (EMCD)

is declared in reference to the harmonized Standards:

EN 60730-1

EN 301 489-1/3 and EN 300 220-3

Description

Connection diagram

8 A / 250 V ~

8 A / 250 V ~ 8 A / 250 V ~ 8 A / 250 V ~

Out 1

Out 2 Out 3 Out 4

I/O extension port

(B) (A)

 Green LED for operating status signaling

 Red LEDS for relay status signaling

 SET BUTTON for channels programming and resetting

Dimensions (mm)

87 mm

72 mm

45 mm

60 mm

65 mm

DY365 4CE

2CSM441048D0201

ABB S.p.A

V.le dell’Industria 18

20010 Vittuone (MI) - Italy

Tel. +39 02 2415 0000

https://new.abb.com/low-voltage

We reserve the right to make technical changes or modify

the contents of this document without prior notice.

Installation Manual







Produkt Specifikationer

Mærke:	ABB
Kategori:	Ikke kategoriseret
Model:	DY365 4CE

Har du brug for hjælp?

Hvis du har brug for hjælp til ABB DY365 4CE stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret ABB Manualer

ABB FW/S 8.2.1 Manual

18 September 2024

ABB S750DR-QA Manual

24 August 2024

ABB US/U 12.2 Manual

9 August 2024

ABB VAA/S6.230.2.1 Manual

1 August 2024

ABB System Pro M DT2-K Manual

1 August 2024

ABB SA/S8.16.2.1 Manual

31 Juli 2024

ABB AW1CO-R-210m Manual

31 Juli 2024

ABB DY GPS Manual

30 Juli 2024

ABB UA63-30-00RA Manual

30 Juli 2024

ABB DWS Manual

25 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Black Diamond HotForge Hybrid Quickpack Manual

31 Juli 2025

RADEMACHER RolloTron Comfort DuoFern 1800 Manual

31 Juli 2025

Infiniton GG-430 Manual

31 Juli 2025

AIC RSC-4ET Manual

31 Juli 2025

Advantech PPC-MB-610 Manual

31 Juli 2025

Intellinet 561730 Manual

31 Juli 2025

Oppo X7 Ultra Manual

31 Juli 2025

Oppo K11 Manual

31 Juli 2025

Bestway Hydro-Force 6531R Manual

31 Juli 2025

RYOBI RSCR4 Manual

31 Juli 2025