Adesso NuScan 2500 Manual

Adesso Stregkodelæser NuScan 2500

Læs gratis den danske manual til Adesso NuScan 2500 (1 sider) i kategorien Stregkodelæser. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Adesso NuScan 2500, eller vil du spørge andre brugere om produktet?

Side 1/1
1
2
3
4
6
7
8
11
QuickGuide
English
www.adesso.com
Bluetooth® and 2.4Ghz Wireless Spill Resistant
Antimicrobial 2D Barcode Scanner
with
Charging Cradle
DESCRIPTION
CONTENTS
Scan Window
Trigger
LED Indicator
Handle
NuScan 2500
NuScan 2500_QSG_EN_04212025
Cradle Quick Start Guide
Cradle USB Cable
INTRODUCTION
The NuScan 2500 is a dual mode Bluetooth and 2.4Ghz Wireless, industrial, water-
proof, antimicrobial, highly portable barcode scanner designed to simplify your job and
increase productivity. Offering a wide scanning range from multiple symbologies from
up to 30 ft away the NuScan 2500TB makes an excellent choice for delivering intuitive
and rapid scanning regardless of the environment!
CHARGING THE DEVICE
1. The scanner is charged via USB cable while sittiing on its charging cradle.
1. Scan below Barcode to select the transfer mode 2.4GHz or Bluetooth. The
scanner is connected to the device via RF 2.4GHz with the Receiver inside the
charging cradle by default.
Re: Unplug the Receiver, scan above
barcode, then insert the RF dongle
within 30 seconds, the beeps will stop
immediately once paired.
Re: make sure it is in bluetooth
mode, scan above barcode, the Led
on the scanner will flash BLUE, and
solid BLUE once paired.
2. Scan below barcode to re-pair with 2.4GHz or Bluetooth if necessary.
Charging the Battery
1. Remove scanner from cradle and press the barcode scanners trigger until the
CONNECTING THE NUSCAN 2500 WITH YOUR DEVICE
SCANNER LED DEFINITIONS
LED Indicators
Descripon
Good Scan Read
BLUE LED BLINK 1 TIME
FLASHING
BLUE LED LIGHT
Off / Sleep Mode
Low Baery
Scanner Charging
Scanner Charged
1 BEEP / LED ON SCANNER OFF
2 BEEPS / SCANNER LED FLASHES
BLUE
LED ON CRADLE SOLID RED
LED ON CRADLE SOLID GREEN
1 BEEP / SOLID BLUE LED LIGHT
Disconnected
1 BEEP AND FLASHING
BLUE LED
Pairing Mode
Paired
Flashing BLUE Light
Go to your ( ) Windows Start Menu
Click on ( ) Settings
Click the catagory Devices ( )
Once inside the Devices catagory, click the word located on the left Bluetooth
2. Please proceed to the instructions that reference whatever device you are using
Transfer Mode Selection
Bluetooth WINDOWS Setup
2. Connect the other end of the USB cable to the host USB power (PC or socket) to
begin charging.
3. The LED indicator will be initially solid
RED to show the scanner is on the charging
cradle. The LED will turn solid
GREEN when charging is completed. It takes 5~6
hours to be fully charged.
LED light on top of scanner flashes
BLUE and then release trigger (this can take
up to 30 seconds).
Trigger
(Windows, Mac, iOS, Andriod...)
column, click the add bluetooth device your Windows device will automatically
start searching for any Bluetooth Devices in the area.
You should see exactly what is shown below. Once you have identified the
Adesso Nuscan 2500, click the word Pair
Once you have clicked the word Pair,Windows will assign your Nuscan 2500
a driver and connect to your scanner. You will see the Window below if successful-
ly connected and the LED light on the top of the Nuscan 2500 will turn solid
BLUE.
Once you have clicked the word Nuscan 2500 your iOS device will connect to your
scanner. You will see the Window below if successfully connected and the LED light
on the top of the Nuscan 2500 will turn solid BLUE .
QuickGuide
English
www.adesso.com
Model: NuScan 2500
Bluetooth® and 2.4Ghz Wireless Spill Resistant
Antimicrobial 2D Barcode Scanner
Imager:640 x 480 CMOS
Light Source: 650 nm visible red LED&White
Microprocessor: 32 bit
Depth of Field: 0 12 inches (UPC/EAN 100%, PCS=90%)
Scan Angle: Roll: ±360°, Pitch: ±45°, Yaw: ±40°
Motion Tolerance: 5 inches per second (IPS)
Minimum Bar Width (1D):5 mil/0.127 mm @ PCS 90%, Code 39
Minimum Bar Width (2D):10 mil/0.254 mm @ PCS 80%, Data Matrix.
Print Contrast: PCS 30% EAN13 @10mil
Indicators (LED): Blue LED successful scan / Red scanning beam
Input Voltage: 5 VDC ±0.5V
Battery Type:Lithium Polymer Rechargeable Battery
Charge Time: 5~6 hours
Cable:6 (1.8 meters)
Dimensions: 6.75 (L) x 3.7 (W) x 2.7 (H) in. (172 x 94 x 68 mm)
Weight: 0.38 lb (174 g; Cradle excluded)
Operating Temperature: 0°C ~ 50°C (32°F ~ 122°F)
Storage Temperature: -40°C ~ 70°C (-40°F ~ 70°F)
Humidity: 5% ~ 95% RH (non-condensing)
LIMITED WARRANTY
Adesso
®
provides a one year limited warranty for all of its products against defects
in materials and workmanship.
During this period, Adesso
®
will repair or replace any product which proves to be
defective. However, Adesso
®
will not warrant any product which has been subject
to improper handling, abuse, negligence, improper installation or unauthorized
repair. The warranty will not cover products installed with components not
approved by Adesso
®
and products where the sealed assembly trace has been
broken.
If you discover a defect, Adesso
®
will, at its option, repair or replace the product free
of charge, provided you return it during the warranty period with freight charges
pre-paid to Adesso
®
. Before returning any product, you must obtain a Return
Merchandise Authorization number (RMA). This RMA # must be clearly marked on
the outside of the package you are returning for warranty service. Be certain to also
include your name, shipping address (no PO Boxes), telephone number, and a
copy of the invoice showing proof of purchase in the package.
We have listed most of our FAQs (Frequently Asked Questions) at: http://www.ades-
so.com/faqs.asp. Please visit our FAQ Service & Support pages before you contact our
E-mail or Telephone Support.
Email Support:
If our FAQs do not help you resolve your issues, please email support@adesso.com
Telephone Support:
Toll Free: (800) 795-6788
9:00AM to 5:00PM PST Monday - Friday
SUPPORT
SPECIFICATIONS
REQUIREMENTS
Connectivity Interface: Windows: 7/8/10/11 & above; Mac OSX & All iPad,
iPhone, & Android OS Devices
Interface: Bluetooth or 2.4Ghz Wireless
CONNECTING WITH MAC OS DEVICE
Go to your Macs Bluetooth Icon ( ) located in the top upper right corner of
your desktop and click on it.
CONNECTING WITH YOUR iOS DEVICE
Locate your iPads or iPhones ( ) on your home screen Settings Icon
and tap on it with your finger.
From the drop down menu, click on Set up Bluetooth Device (Your Mac will
automatically start searching for any Bluetooth Devices in the area)
You should see exactly what is shown below. Once you have identified the
Nuscan 2500, click the word Continue to proceed.
Once you have clicked the word Pair,Windows will assign your Nuscan 2500
a driver and connect to your scanner. If successfully connected and the LED light
on the top of the Nuscan 2500 will turn solid BLUE.
Once in your settings, click on in the left column. (BluetoothYour iOS device
will automatically start searching for any Bluetooth Devices in the area). You should
see exactly what is shown below. Once you have identified the Nuscan 2500,
click the word.
INVENTORY MODE
NORMAL MODE
Scan below barcode to enter “Inventory Mode”. In inventory mode, the scanner will not
display the barcodes you scan and will not output them onto your device. Instead, the
scanner will store them in its built-in memory chip.
Scan below barcode to exit “Inventory Mode”. and enter “Normal Mode”. In normal mode
your scanned barcodes will be uploaded into your device as your scanning.
Scan below barcode to show the total count of
the number of barcodesstored in inventory mode.
Scan below barcode to upload your stored barcodes.
Scan below barcode to erase your stored barcodes.
Inventory Mode
Total Count
Upload Barcodes
Clear Memory
Normal Mode
5
9
10
12
RETURN TO FACTORY DEFAULT
Factory Default:
SCANNING MODE:
Continuous:
Manual Trigger:
MESSAGE TERMINATOR:
No Terminator:
Enter/Return
Carriage:
Horizontal Tab:
SLEEP TIMER SETTINGS
iOS On Screen Keyboard
Scan below barcodes to set dierent sleep timers for the scanner. By default sleep
timer is set to 1 minute.
When the scanner is rst connected to your iOS device, the on screen keyboard will
disappear because the device recognizes the scanner as a keyboard input. Scan the
below barcode and the on screen keyboard will reappear.
3 minutes
iOS On Screen Keyboard
30 minutes
10 minutes
Never
2.4GHz Mode
Bluetooth Mode
2.4GHz Pairing Bluetooth Pairing


Produkt Specifikationer

Mærke: Adesso
Kategori: Stregkodelæser
Model: NuScan 2500

Har du brug for hjælp?

Hvis du har brug for hjælp til Adesso NuScan 2500 stil et spørgsmål nedenfor, og andre brugere vil svare dig