1
ENGLISH H 500, H 750, HB 750, HBE 800
You demand the best and buy quality – quality provided by Atlas Copco.
We have built for you a reliable and lasting tool. Working effectively and without
endangering your health is only possible if these instructions for use are being read
carefully before first using this tool. We want to satisfy our customers and would
like you to buy again AEG Electric Power Tools from Atlas Copco.
H 500 H 750 HB 750 HBE 800
Nominal power 500 W 750 W 750 W 800 W. . . . . . . . . . . . . . . . . . . . . . . . . . .
Planing width 82 mm 82 mm 102 mm 102 mm. . . . . . . . . . . . . . . . . . . . . . . .
Planing depth 0–1,6 mm 0–2,5 mm 0–2,0 mm 0–2,0 mm. . . . . . . . . . . . . .
Rabbet depth 0–16 mm 0–22 mm 0–22 mm 0–22 mm. . . . . . . . . . . . . . . . . .
No-load speed 17000 min-1 13000 min-1 13000 min-1 11000 min-1
. . . . . . . . . .
Weight 2,5 kg 3,5 kg 3,7 kg 3,8 kg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Please pay attention to the safety instructions in the attached leaflet!
Appliances used at many different locations including open air must be connected
via a current surge preventing switch.
Always use the protective shields on the machine.
Always wear goggles when using the machine. It is recommended to wear gloves,
sturdy non slipping shoes and apron.
Sawdust and splinters must not be removed while the machine is running.
Do not pierce the motor housing as this could damage the double insulation (use
adhesives).
Always disconnect the plug from the socket before carrying out any work on the
machine.
Keep mains lead clear from working range of the machine. Always lead the cable
away behind you.
Before switching on ensure that protective swing cover moves freely.
Only plane with sharp blades and avoid metal (nails, screws).
When doing stationary planing (not rabbeting) use the guard.
For stationary operation, for trimming small pieces of wood also use push stick.
Only put the planer down after the blades have stopped moving.
The protective swing cover and the blade drive cover on the side must be easy to
move to and fro.
The protective swing cover must not be locked open except when the plane is
beeing used in afixed mounting.
Operate the protective swing cover only by means of the lever or automatically by
pressure against the piece being planed.
In the fixed position, the plane may only be used in the Atlas Copco stationary
mounting or in the Atlas Copco dressing and planing table.
Do not put the machine down until the blade drive has stopped running.
Never reach into the danger area of the plane when it is running.
Typically the A-weighted noise levels of the tool are:
Sound pressure level = 87 dB (A). Sound power level = 100 dB (A).
Wear ear protectors!
Typically the hand-arm vibration is below 2.5 m/s2.
The plane can plane surfaces and rabetts, and bevel and chamfer edges.
Do not use this product in another way as stated for normal use.
Connect only to a single-phase AC current supply and only to the mains voltage
specified on the rating plate. Connection to sockets without earth protection is
possible as the appliance features protective insulation to DIN 57 740/ VDE 0740
and CEE 20. Radio suppression complies with the European standard EN 55014.
When fitting the plug, make sure that the brown (live) wire of this appliance is
connected to the plug terminal marked L or coloured red, and the blue (neutral) wire
of this appliance is connected to the plug terminal marked N or coloured black.
Under no circumstances must the wires of this appliance be connected to the earth
terminal of the plug marked either E, with the earth symbol or coloured green or
green/yellow.
The range of accessories with part numbers is shown in our catalogue.
Introduction
Technical Data
Advice for your
safety
Measured sound
value
Measured
vibration value
Use
Mains
connection
Accessories
