Aeon Labs Extender Manual

Aeon Labs Smart hjem Extender

Læs gratis den danske manual til Aeon Labs Extender (5 sider) i kategorien Smart hjem. Denne vejledning er vurderet som hjælpsom af 70 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 35.5 anmeldelser. Har du et spørgsmål om Aeon Labs Extender, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

Image not readable or empty

images/manufacturers/aeon%20labs%20logo.png

AEO_EXTENDER

Z-Wave Extender

Firmware Version : 0.0

Quick Start

S This device is a wireless Z-Wave sensor. A single click on the Z-Wave switch will conﬁrm Inclusion and

Exclusion.

Please refer to the chapters below for detailed information about all aspects of the products usage.

What is Z-Wave?

This device is equipped with wireless communication complying to the Z-Wave standard. Z-Wave is the

international standard for wireless communication in smart homes and buildings. It is using the

frequency of 868.42 MHz to realize a very stable and secure communication. Each message is reconﬁrmed

( ) and every mains powered node can act as a repeater for other nodes (two-way communication meshed

network) in case the receiver is not in direct wireless range of the transmitter.

Z-Wave diﬀerentiates between Controllers and Slaves. Slaves are either sensors transmitting metered or (S)

measured data or actuators capable to execute an action. Controllers are either static mains powered (A)

controllers also referred to as gateways or mobile battery operated remote controls . This results in a (C) (R)

number of possible communication patterns within a Z-Wave network that are partly or completely supported

by a speciﬁc device.

1. Controllers control actuators

2. Actuators report change of status back to controller

3. Sensors report change of status of measured values to controller

4. Sensors directly control actuators

5. Actuators control other actuators

6. Remote controls send signals to static controllers to trigger scenes or other actions

7. Remote controls control other actuators.

There are two diﬀerent role a controller can have. There is always one single primary controller that is managing the

network and including/excluding devices. The controller may have other functions - like control buttons - as well. All other

controllers don't manage the network itself but can control other devices. They are called secondary controllers. The

image also shows that its not possible to operate a sensor just from a remote control. Sensors only communicate with

static controllers.

Product description

This device take existing Z-WAVE signal, repeat and send it to a longer range where it is too far away for

the controller (supporting FLiRS devices). Due to a special antenna ampliﬁer the operating range will be up

to 200 meters when installed correctly.

Before Device is installed

Please read carefully the enclosed user manual before installation of the radio-actuator, in order to ensure

an error-free functioning.

ATTENTION: only authorized technicians under consideration of the country-speciﬁc installation

guidelines/norms may do works with 230?Volt mains power. Prior to the assembly of the product, the

voltage network has to be switched oﬀ and ensured against re-switching.

The product is permitted only for proper use as speciﬁed in the user manual. Any kind of guarantee claim

has to be forfeited if changes, modiﬁcations or painting are undertaken. The product must be checked for

damages immediately after unpacking. In the case of damages, the product must not be operated in any

case. If a danger-free operation of the equipment cannot be assured, the voltage supply has to be

interrupted immediately and the equipment has to be protected from unintended operation.

Installation Guidelines

Produkt Specifikationer

Mærke:	Aeon Labs
Kategori:	Smart hjem
Model:	Extender
Vekselstrømsindgangsspænding:	240 V
Vekselstrømsindgangsfrekvens:	50 Hz
Maksimal overførselsafstand:	200 m
Driftsfrekvens:	868.42 MHz
Antal produkter inkluderet:	1 stk