AIM Sportline Multichron Manual

AIM Sportline Diverse Multichron

Læs gratis den danske manual til AIM Sportline Multichron (3 sider) i kategorien Diverse. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om AIM Sportline Multichron, eller vil du spørge andre brugere om produktet?

Side 1/3
Release 1.04
Aim s.r.l. Via Cavalcanti 8, 20063 Cernusco sul Naviglio – MI – ITALY
Tel (+39) – 02- 9290571 . Fax (+39) – 02 – 92118024 www.aim-sportline.com
1) Initial set up When you first use the Multichron, press the CONF-SPEED button to set the following options (press the plus or
minus buttons to vary the settings and then press the DATA-STOP button to move to the next line):
i) Contrast (to alter the display and viewing angle)
ii) Light on/off (for versions with backlight)
iii) Beep sound on/off
iv) Send (IRDA) PC transmission data (see PC data section)
v) Econ on/off (Power saver, when “on” the display closes down until a button is pressed.
Press the CONF-SPEED button to move to the next set up screen:
vi) Alarm on/off
vii) Set the time when the alarm will go off (use the DATA-STOP button to choose the hours and minutes to change. Change
the flashing digit by using the plus or minus button.
viii) Chime on/off (when “on” the multichron beeps every 30 minutes)
ix) Time of day: Use the same button logic as in vii) above to set the correct time of day. The default setting is 12 hour mode.
You can change this from A (am) to P (pm) or _ (24 hour mode)
Press the CONF-SPEED button to move to the next set up screen:
x) Distance measurement ( you can choose between Miles or Kilometers
Competitor 2,3 and 4
previous lap/current lap
times
Competitor 1 previous lap
time
Competitor 1 current lap
running time.
Lap number
Number in SPL
column shows the
number of split
times per lap. A b
in this column
denotes best time
Use – set + when configuring your required
settings
For competitor
1,2,3 and 4 timing
IR PC Data Transmission system
Release 1.04
Aim s.r.l. Via Cavalcanti 8, 20063 Cernusco sul Naviglio – MI – ITALY
Tel (+39) – 02- 9290571 . Fax (+39) – 02 – 92118024 www.aim-sportline.com
xi) Length of the Circuit: Enter the distance to be timed (optional)
xii) Stopwatch operating mode: Multi /Single (see operating mode section)
xiii) Stopwatch operating mode: Multi start/One start (see operating mode section)
xiv) Stopwatch operating mode: Timer on/off (see operating mode section)
Press the CONF-SPEED button to move to the next set up screen:
xv) Countdown timer settings: Use the same button logic as in vii) above to set the required countdown time
When the settings are complete, press the MODE button to go to either Stopwatch, Data review, Countdown or Alarm screens.
Stopwatch operating mode
Multichron offers four ways of capturing split/lap times using a combination of two options:
Multi or One start: Choose Multi-start if competitors start at different times. Choose One-start if competitors start at the same time.
Single mode/multi mode:
Single mode allows you to take lap times and or split times by pressing the LAP/STARTand or RESET/SPLIT button to take a
time then allocate the competitor number later (useful when competitors are close together)
Multi mode allows you to take lap times and or split times and is best for timing when competitors are less close together.
There are four operating modes for you to choose from:
Multi Mode, Multi Start = Competitors start at individual times
To take lap times for up to 4 competitors:
Press START/LAP button when competitor 1 begins.
The bottom display shows competitor 1’s current lap running time.
Press button 2 when competitor 2 begins, Press button 3 when competitor 3 begins and Press button 4 when competitor 4 begins.
The current running lap time is shown for each competitor.
Press button 1, 2, 3 and 4 when each competitor completes a lap. A lap time is taken and the next lap starts timing from zero.
Repeat this process until you have the required number of lap times.
The display will show the previous lap number and time for each competitor and the current running lap time for competitor 1.
After a short time, the display for competitors 2,3 and 4 return to current lap running time.
You can also capture up to 9 split times within a lap for each competitor as well as lap times:
To do this, press and hold down the RESET/SPLIT button. When you want to take the split time, press the buttons for the
competitors (button 1 for competitor 1 etc.)
The display will show the lap number, the number of splits within that lap and the last split time. After a short time, the display
returns to current lap running time.
Multi Mode, One Start = Competitors start at the same time
To take lap times for up to 4 Competitors:
Press START/LAP button when competitors start the event
The bottom display shows competitor 1’s current lap running time.
Press button 1,2,3,4 to take competitors 1,2,3 and 4’s lap times
The display will show the previous lap number and time for each competitor and the current running lap time for competitor 1.
After a short time, the display for competitors 2,3 and 4 return to current lap running time.
Repeat this process until you have the required number of lap times.
Note: Pressing the START/LAP button in this mode will only capture lap times for competitor 1.
You can also capture up to 9 split times within a lap for each competitor as well as lap times:


Produkt Specifikationer

Mærke: AIM Sportline
Kategori: Diverse
Model: Multichron

Har du brug for hjælp?

Hvis du har brug for hjælp til AIM Sportline Multichron stil et spørgsmål nedenfor, og andre brugere vil svare dig