Aimpoint CompM2 Manual

Aimpoint Ikke kategoriseret CompM2

Læs gratis den danske manual til Aimpoint CompM2 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 21 anmeldelser. Har du et spørgsmål om Aimpoint CompM2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Aimpoint AB

Jägershillgatan 15

SE- 213 75 Malmö, Sweden

Phone +46 (0)40 671 50 20

Fax +46 (0)40 21 92 38

e-mail: info@aimpoint.se

www.aimpoint.com

Aimpoint Inc.

14103 Mariah Court

Chantilly, VA 20151-2113, USA

Phone +1 703-263-9795

Fax +1 703-263-9463

e-mail: info@aimpoint.com

www.aimpoint.com

User Manual for

Aimpoint CompM2

and

Aimpoint CompML2

CHAPTER III – OPERATION UNDER EXTREME CONDITIONS

a. Extreme heat (moist or dry): No special procedures required.

b. Extreme cold: Extreme cold might shorten battery life. Keep spare batteries

in your inner pockets to keep them warm.

c. Salt air: No special procedures required.

d. Sea spray, water, mud and snow: Ensure that the Battery cap (2) and the

two Adjustment screw caps (5) are tight before exposing the sight to sea

spray, mud, snow or before submersing the sight into water. Hand tighten

only. Keep lens covers closed when the sight is not being used. Clean

lenses with lens paper/cloth and wipe the sight dry as soon as possible

after exposure to water, sea spray, mud or snow.

e. Dust storms and sand storms: Keep lens covers closed when the sight is

not being used.

f. High altitudes: No special procedures required.

CAUTION: The lenses shall never be cleaned with ngers but with lens

paper/cloth. If lens paper/cloth is not available:

– To clear away debris (sand, grass etc): blow away the dirt or rinse with

clear water.

– To clean lenses: mist up the lenses or rinse with clear water and clean

them with a soft piece of cloth.

2.2 OPERATING PROCEDURES

2.2.1 Zeroing

Aimpoint’s sights are delivered in a centered position. Normally this means

that only small adjustments are necessary, providing that the base(s) are

properly aligned.

CAUTION: Do not continue to adjust windage and elevation mechanisms if

you encounter resistance.

The elevation Adjustment screw is located on top of the sight, while the

windage screw is located on the right or left side, depending on how the

sight has been mounted on the weapon. Aimpoint sights can be installed to

support either right hand (g. 2) or left hand (g. 3) shooters.

a. Open Front and Rear Lens covers (9) and (8).

b. Turn the Rotary switch (4) clockwise until the red dot has a sufcient

intensity to contrast against target.

NOTE: Each click of the Adjustment screws (7) corresponds to a 13 mm

movement of the point of impact at 80 meters, (4 mm at 25 meters, 16 mm at

100 meters and 32 mm at 200 meters or 1/4” at 50 yds, 1/2” at 100 yds and

1” at 200 yds).

c. Insert adjustment tool (coin, screwdriver, knife) or cartridge casing in

Adjustment screw slot (7) and turn as follows:

• To move the point of impact to the right, turn windage adjustment screw

counter clockwise (clockwise if screw located on left side).

• To move the point of impact to the left, turn windage adjustment screw

clockwise (counter clockwise if screw located on left side).

• To move the point of impact up, turn elevation adjustment screw counter

clockwise.

• To move the point of impact down, turn elevation adjustment screw

clockwise.

d. Conrm zeroing by ring at least three shots at a zeroing target. Check

impact points on zeroing target to conrm accuracy and repeat above

procedure if required.

e. After initial ring, ensure that the mount and sight are secure.

f. Turn Rotary switch (4) to OFF position (counter clockwise).

g. Close front and rear Lens cover (9) and (8).

CHAPTER IV – TROUBLE SHOOTING PROCEDURES

4.1 RED DOT DOES NOT APPEAR

Discharged battery: Replace Battery (3)

Battery installed incorrectly: Remove and reinstall Battery (3)

with (+) toward Battery cap (2).

Battery is not making good contact: Clean contact surfaces and

reinstall Battery (3).

Defective rotary switch: Notify dealer/armourer

4.2 IMPOSSIBLE TO ZERO

Adjustment screw is at its limit: Check alignment of mount to barrel

Impact point is moving: Check mount stability

CHAPTER V – MAINTENANCE

a. This reex sight does not require any particular maintenance while used

under normal conditions.

b. Under severe weather conditions please refer to CHAPTER III.

c. Keep Lens covers (8) and (9) closed whenever the sight is not in use.

d. Warehouse storage: Remove Battery (3) and allow lens surfaces to dry

completely (if wet) before closing the Lens covers (8) and (9).

e. To clean lenses refer to CAUTION in CHAPTER III.

Produkt Specifikationer

Mærke:	Aimpoint
Kategori:	Ikke kategoriseret
Model:	CompM2
Vægt:	220 g
Produktfarve:	Sort
Husmateriale:	Aluminium
Vandtæt op til:	25 m
Vandfast:	Ja
Batterier inkluderet:	Ja
Batteritype:	Lithium 3V
Optisk zoom:	- x
Længde:	130 mm
Linse, diameter:	- mm
Beskyttelsesdæksel:	Ja
Maksimal forstørrelse:	1 x
Egenskaber for linsebelægning:	Anti-reflekterende
Rør, diameter:	30 mm
Konstant øjenlindring:	- mm
Klik værdi:	1/2 MOA
Objektiv tromlediameter:	38 mm