American Standard 7075.100.002 Manual

American Standard Kran 7075.100.002

Læs gratis den danske manual til American Standard 7075.100.002 (4 sider) i kategorien Kran. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 10 anmeldelser. Har du et spørgsmål om American Standard 7075.100.002, eller vil du spørge andre brugere om produktet?

Side 1/4
- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2016
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS
1
M965764 (8/16)
INSTALL FAUCET
COLONY® PRO
SINGLE LEVER MONOBLOCK
LAVATORY FAUCET
INSTALLATION
INSTRUCTIONS
7075.100
7075.102
7075.104
Screwdriver Adjustable Wrench Tubing CutterChannel Locks
Certied to comply with ANSI A112.18.1M
2
5
8
4
MOUNTING
SURFACE
3
Figure A
(OPTIONAL
DECK PLATE)
2000102P-YYY
1
CAUTION Turn off hot and cold water
supplies before begining.
Seat SEAL into under side of FAUCET BODY (2) (1).
FAUCET SUPPLIES , MOUNTING STUD and DRAIN ASSEMBLY Feed (3) (4)
(8) through the mounting hole of lavatory. Figure A.
below, push GASKET and RETAINING WASHER From (7) (5) onto
MOUNTING STUD . Secure Faucet with MOUNTING NUT (4) (6), pulling
faucet to front of sink, so SUPPLIES (3) rests against mounting hole.
Before nal tightening, make sure collar on MOUNTING NUT (6) is
seated into RETAINING WASHER (5).
Faucet so that it is centered. Tighten MOUNTING NUT Adjust (6)
to complete faucet mounting.
6
4
COLLAR ON
MOUNTING NUT
7
5
Figure B
- 2 -
2
3
4
Operate LIFT KNOB (1) to verify that
STOPPER (2) opens and closes.
CHECK OPERATION OF POP-UP
MAKE WATER SUPPLY AND WASTE CONNECTIONS
M965764 (8/16)
• Push TAIL PIECE TRAP (11) down into (C) (threaded end up).
Thread LOCKNUT WASHER GASKET (5), and (4) (3)
(Bevel side up) onto DRAIN BODY (10).
• Apply a bead of PUTTY FLANGE (D) to underside of (2).
Feed DRAIN BODY SINK up through (10) (A) and thread
the fully onto .FLANGE (2) DRAIN BODY (10)
Tighten LOCKNUT (5) rmly, keeping the pivot rod hole pointed
towards the back of the sink.
Assemble PIVOT ROD (9) Figure-2a. as shown in
Notice the position of the CONCAVE WASHER (G).
Insert PIVOT ROD DRAIN BODY (9) into (10) and tighten
PIVOT NUT (F).
Pull TAIL PIECE (11) up and thread tightly into
DRAIN BODY .(10)
Position EXTENSION ROD POP-UP ROD(7) onto (E) and tighten
THUMBSCREW (6).
Remove one end of PIVOT ROD ENDS TOGETHER WHILE SLIDING.CLIP from (8) (9) by squeezing
Insert PIVOT ROD EXTENSION ROD (9) into second or third hole in (7) and reassemble CLIP .(8)
• DROP STOPPER DRAIN BODY (1) into (10).
Adjust stopper height by repositioning EXTENSION ROD THUMBSCREW (7) and tightening (6).
INSTALL POP-UP DRAIN
1
APPROX. 20"
2
COLD
HOT
3/8" COMPRESSION
RED
BAND
BLUE
BAND
Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
Connection on tting supplies are 3/8 compression. "
Connect left SUPPLY to Hot (Marked with a Red Band) (1)
and right supply to COLD (2) wall supply.
Faucet supplies are 20 long from faucet base. "
Note: If additional supply length is required, installer must
purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are to long, loop as
illustrated to avoid kinking.
1-1/4"
6
E
D
7
8
9
C
F
2
A
1
3
4
5
10
11
2a
F
G
2
1


Produkt Specifikationer

Mærke: American Standard
Kategori: Kran
Model: 7075.100.002

Har du brug for hjælp?

Hvis du har brug for hjælp til American Standard 7075.100.002 stil et spørgsmål nedenfor, og andre brugere vil svare dig