American Standard Colony Pro 7075.002.002 Manual

American Standard Vandhane Colony Pro 7075.002.002

Læs gratis den danske manual til American Standard Colony Pro 7075.002.002 (4 sider) i kategorien Vandhane. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 14 anmeldelser. Har du et spørgsmål om American Standard Colony Pro 7075.002.002, eller vil du spørge andre brugere om produktet?

Side 1/4
- 1 -
SINK OR
MOUNTING
SURFACE
2
3
4
1
(HAND TIGHTEN)
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2016
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS
1
M965766 (8/16)
INSTALL FAUCET
COLONY® PRO
SINGLE CONTROL
CENTERSET
LAVATORY FAUCET
INSTALLATION
INSTRUCTIONS
7075.054 / 7075.055 / 7075.056
7075.050 / 7075.004 / 7075.005
7075.006 / 7075.002 / 7075.000
Screwdriver Adjustable Wrench Tubing CutterChannel Locks
Certied to comply with ANSI A112.18.1M
CAUTION Turn off hot and cold water
supplies before begining.
Insert FAUCET and POP-UP CABLE (1) (2) through mounting
holes of Sink or Mounting Surface.
Assemble LOCKNUTS onto SHANKS (3) (4) from under
side of Sink. Hand tight
- 2 -
2
3
4
Operate LIFT KNOB (1) to verify that
STOPPER (2) opens and closes.
CHECK OPERATION OF POP-UP
MAKE WATER SUPPLY AND WASTE CONNECTIONS
M965766 (8/16)
• Push TAIL PIECE TRAP (11) down into (C) (threaded end up).
Thread LOCKNUT WASHER GASKET (5), and (4) (3)
(Bevel side up) onto DRAIN BODY (10).
• Apply a bead of PUTTY FLANGE (D) to underside of (2).
Feed DRAIN BODY SINK up through (10) (A) and thread
the fully onto .FLANGE (2) DRAIN BODY (10)
Tighten LOCKNUT (5) rmly, keeping the pivot rod hole pointed
towards the back of the sink.
Assemble PIVOT ROD (9) Figure-2a. as shown in
Notice the position of the CONCAVE WASHER (G).
Insert PIVOT ROD DRAIN BODY (9) into (10) and tighten
PIVOT NUT (F).
Pull TAIL PIECE (11) up and thread tightly into
DRAIN BODY .(10)
Position EXTENSION ROD POP-UP ROD(7) onto (E) and tighten
THUMBSCREW (6).
Remove one end of PIVOT ROD ENDS TOGETHER WHILE SLIDING.CLIP from (8) (9) by squeezing
Insert PIVOT ROD EXTENSION ROD (9) into second or third hole in (7) and reassemble CLIP .(8)
• DROP STOPPER DRAIN BODY (1) into (10).
Adjust stopper height by repositioning EXTENSION ROD THUMBSCREW (7) and tightening (6).
INSTALL POP-UP DRAIN
1
APPROX. 20"
2
COLD
HOT
3/8" COMPRESSION
RED
BAND
BLUE
BAND
Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
Connection on tting supplies are 3/8 compression. "
Connect left SUPPLY to Hot (Marked with a Red Band) (1)
and right supply to COLD wall supply.(2)
Faucet supplies are 20 long from faucet base. "
Note: If additional supply length is required, installer must
purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are to long, loop as
illustrated to avoid kinking.
Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to
waste outlet.
1-1/4"
6
E
D
7
8
9
C
F
2
A
1
3
4
5
10
11
2a
F
G
2
1


Produkt Specifikationer

Mærke: American Standard
Kategori: Vandhane
Model: Colony Pro 7075.002.002

Har du brug for hjælp?

Hvis du har brug for hjælp til American Standard Colony Pro 7075.002.002 stil et spørgsmål nedenfor, og andre brugere vil svare dig