Amprobe CT-326-C Manual

Amprobe Ikke kategoriseret CT-326-C

Læs gratis den danske manual til Amprobe CT-326-C (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Amprobe CT-326-C, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
CT-326-C Current Tracer
Probe Range Switch
1. Range switch determines the probe’s gain.
2. If the probe displays 10 LEDs, gain is too sensitive. Turn switch to lower setting.
Identify Circuit Breaker (Fig. 2)
1. Connect the transmitter to a source of power.
2. Set the probe’s range switch to BREAKERS-3.
3. Push ON and wait for it to calibrate.
4. Hold the probe’s tip to each circuit breaker as shown. The correct breaker
produces the strongest signal. Adjust gain as necessary.
5. In critical areas, remove panel trim and turn the probe’s range switch to
WIRES-1. Hold the tip to each wire. The wire with the strongest signal may
be visually traced to the breaker.
Locating Wires In Walls (Fig. 3)
1. Attach pigtail connector to transmitter.
2. Clip one lead to a seperate earth ground such as a water pipe.
3. Clip the other lead to the hot conductor.
4. Set the probe’s range switch to SCAN position.
5. Push ON and wait for it to calibrate.
6. Hold the probe’s tip close to the wall or floor where you suspect the
conductor is located.
7. Sweep the probe across large areas until the probe’s signal locates the
conductor. Adjust range switch as necessary.
NOTE: The same procedure may be used for tracing individual wires in
bundles.
Following Conduit (Fig. 4)
1. Attach transmitter and follow signal as explained in
“Locating Wires in Walls”.
2. Adjust the probe’s range switch as necessary.
HINT: Since the feeder panel may radiate a magnetic signal to
nearby conduit, make sure the probe is always more than 5’
(1.5 m) away from the circuit breaker box.
Fig. 4
Fig. 3
Fig. 1
Fig. 2
Test Position (Fig. 1)
1. Connect the transmitter to source of power.
2. Set the probe’s range switch to BREAKERS-5.
3. Push ON and wait for it to calibrate.
4. Hold the probe next to the transmitter, observe blinking LEDs and
“chirping” sound.
Probe Battery Test
1. Push the probe’s BATTERY TEST and ON buttons at the same time.
2. If the probe’s LEDs do not light in BATTERY OK range, change the battery.
Short To Ground (Fig. 5)
1. Find affected breaker panel and make sure circuit breaker is in
OFF position.
2. Attach pigtail connector to transmitter.
3. Clip one lead to shorted power line.
4. Clip the other lead to hot conductor of adjacent breaker as
shown.
5. Adjust the probe’s range switch as necessary.
6. Push ON and wait for it to calibrate.
7. Hold the tip close to the shorted wire.
8. Trace the wire until the signal suddenly stops. This is the
location of the short. Fig. 5
Fig. 7
Tracing Coax Cable (Fig. 6)
1. Attach pigtail connector to transmitter.
2. Clip one lead to the shield of the coax cable.
3. Clip other lead to grounded power source.
4. Follow the transmitter’s signal as explained in
“Locating Wires in Walls”.
NOTE: Make sure the coax shield is grounded.
Locating Ground Faults (Fig. 7)
1. Identify ground fault with voltmeter. Grounded
phase will have reduced voltage compared to the
other phases.
2. Attach pigtail connector to transmitter.
3. Clip one lead to system ground.
4. Connect the other lead to one of the two
phases that doesn’t have the ground fault. The
transmitter’s LED will blink if the ground fault
impedance is low enough to allow the transmitter to operate.
5. Adjust the probe’s range switch as necessary.
6. Push ON and wait for the probe to calibrate.
7. Hold the probe’s tip close to a faulty phase and watch for a dramatic change in LED readout.
Fig. 6
Amprobe®
www.Amprobe.com
info@amprobe.com
Everett, WA 98203
Tel: 877-AMPROBE (267-7623)
Amprobe® Europe
Beha-Amprobe
In den Engematten 14,
79286 Glottertal, Germany
Tel.: +49 (0) 7684 8009 - 0
P/N 3356291 Rev 002
10/2013 6001650 A
©2013 Amprobe® Test Tools. All rights reserved.

Produkt Specifikationer

Mærke: Amprobe
Kategori: Ikke kategoriseret
Model: CT-326-C

Har du brug for hjælp?

Hvis du har brug for hjælp til Amprobe CT-326-C stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Amprobe Manualer

Amprobe

Amprobe AD40B Manual

28 September 2024
Amprobe

Amprobe TMD-55W Manual

19 August 2024
Amprobe

Amprobe THWD-10W Manual

15 August 2024
Amprobe

Amprobe WT-20 Manual

13 August 2024
Amprobe

Amprobe VPC-10 Manual

12 August 2024
Amprobe

Amprobe TP110KA Manual

11 August 2024
Amprobe

Amprobe BAT-100 Manual

11 August 2024
Amprobe

Amprobe AT-4001-A Manual

4 August 2024
Amprobe

Amprobe FLASH-80 Manual

4 August 2024
Amprobe

Amprobe AC50A Manual

4 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

OmniMount

OmniMount POWER40 Manual

17 Juni 2025
OmniMount

OmniMount OL50FT Manual

17 Juni 2025
Intermatic

Intermatic FD30MHW Manual

17 Juni 2025
Toorx

Toorx SRX-EVOLVE Manual

17 Juni 2025
OmniMount

OmniMount WorldMount 2N1-L Manual

17 Juni 2025
OmniMount

OmniMount WorldMount 4N1-L Manual

17 Juni 2025
Intermatic

Intermatic FD60MC Manual

17 Juni 2025
Microchip

Microchip MPFS160TLS Manual

17 Juni 2025
Hughes & Kettner

Hughes & Kettner Metal Master Manual

17 Juni 2025
Hansgrohe

Hansgrohe AXOR Montreux 16516310 Manual

17 Juni 2025