Amtrol Therm-X-Trol ST-200V Manual

Amtrol Kedler & kedler Therm-X-Trol ST-200V

Læs gratis den danske manual til Amtrol Therm-X-Trol ST-200V (2 sider) i kategorien Kedler & kedler. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Amtrol Therm-X-Trol ST-200V, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

USE ONLY WITH RESIDENTIAL POTABLE

WATER SYSTEMS. Do not operate in a setting

with freezing temperatures or where the temperature can exceed 200°F

and do not exceed the maximum working pressure specified for this

Product. Do not use on a system with ASME-rated vessels.

READ CAREFULLY THE PRODUCT

INSTALLATION, OPERATING AND

MAINTENANCE MANUAL. FAILURE TO FOLLOW THE

INSTRUCTIONS AND WARNINGS IN THE MANUAL MAY RESULT IN

SERIOUS OR FATAL INJURY AND/OR PROPERTY DAMAGE, AND

WILL VOID THE PRODUCT WARRANTY. THIS PRODUCT MUST BE

INSTALLED BY A LICENSED PROFESSIONAL. FOLLOW ALL

APPLICABLE LOCAL AND STATE CODES AND REGULATIONS, IN

THE ABSENCE OF SUCH CODES, FOLLOW THE CURRENT

EDITIONS OF THE NATIONAL PLUMBING CODE AND NATIONAL

ELECTRIC CODE, AS APPLICABLE.

This Product, like most Products under pressure,

may over time corrode, weaken and burst or

explode, causing serious or fatal injury, leaking or flooding and/or

property damage. To minimize risk, a licensed professional must install

and periodically inspect and service the Product. Do not install this

product where leaking or flooding could cause property damage to the

area adjacent to the appliance or to lower floors of the structure.

RUPTURE OR EXPLOSION HAZARD. Do not

expose Product to freezing temperatures or

temperatures in excess of . Do not adjust the pre-charge or 200°F

re-pressure this Product except during installation or regular inspection.

Replace the Product and do not adjust the precharge if corroded,

damaged or with diminished integrity. Adjustments to pre-charge must be

done at ambient temperature only. Failure to properly size the Product or

follow these instructions may result in excessive strain on the system and

may lead to Product failure, serious or fatal personal injury, leakage and/

or property damage.

A relief valve must be installed to prevent pressure

in excess of local code requirement or maximum

working pressure designated in the Product Manual, whichever is less.

At least once every 3 years or if discharge is present, a licensed

professional should inspect the temperature and pressure relief valve

and replace if corrosion is evident or the valve does not function.

FAILURE TO INSPECT THIS VALVE AS DIRECTED COULD RESULT

IN UNSAFE TEMPERATURE OR PRESSURE BUILD-UP WHICH CAN

RESULT IN PRODUCT FAILURE, SERIOUS INJURY OR DEATH AND/

OR SEVERE PROPERTY DAMAGE AND VOID THE PRODUCT

WARRANTY.

Chlorine & Aggressive Water: The water quality

can significantly influence the life of this Product.

You should test for corrosive elements, acidity, total solids and other

relevant contaminants, including chlorine and treat your water

appropriately to insure satisfactory performance and prevent premature

failure.

This product can expose you to chemicals including

lead, which is known to the State of California to

cause cancer and birth defects or other reproductive harm. For more

information go to www.P65Warnings.ca.gov.

THERMAL EXPANSION TANKS

FOR POTABLE WATER

INSTALLATION & OPERATION INSTRUCTIONS

Models ST-5 through ST-210V

Models T-5 and T-12

NOTE: Inspect for shipping damage and notify freight carrier or store where purchased immediately if damage is present. To avoid risk of personal

injury and property damage, if the product appears to be malfunctioning or shows signs of corrosion, call a qualified professional immediately. Current

copies of the Product manual can be viewed at www.amtrol.com. Use proper safety equipment when installing.

THIS IS THE SAFETY ALERT SYMBOL. IT IS USED TO ALERT YOU TO POTENTIAL PERSONAL INJURY AND OTHER

HAZARDS. OBEY ALL SAFETY MESSAGES THAT FOLLOW THIS SYMBOL TO REDUCE THE RISK OF PERSONAL

INJURY AS WELL AS PROPERTY DAMAGE.

Pre-Installation

1 Ensure expansion tank is sized properly for application (Figure 1).

2. Remove plastic cap from air valve.

3. With tank empty of water, adjust air precharge to match cold water

supply pressure.

4. Replace and tighten plastic cap on air valve.

5. ST-5 and ST-12 only: Insert Turbulator

™ into connector.

FAILURE TO PROPERLY SEAL VALVE CAP

WILL RESULT IN LOSS OF PRECHARGE

CAUSING PRODUCT TO FAIL.

Installation

1. Install the expansion tank on the cold water supply line to the water

heater at a point between the water heater and backflow preventer or

other one-way device (Figure 2).

Mount vertically only. Ensure that tank is

supported properly to hold the entire weight of

the tank when full of water.

Models ST-25V through ST-210V are floor

standing and may not be hung from the piping.

2. Once the expansion tank is installed, check the cold water supply line

for any leakage. Make repairs if necessary.

3. Before the initial firing of the water heater, open a hot water fixture and

draw for one minute to purge air. Next, close and open the fixture in 30

second intervals, repeating three thimes to flush the tank and piping.

Finally, turn the water heater temperature control to desired ending

temperature (see water heater instructions). Do not set temperature

higher than the expansion tank maximum.

4. To relieve initial thermal expansion, momentarily open a hot water

faucet. Continue until water heater aquastat temperature is satisfied.

Once heater is at its operating range, no further bleeding of expanded

water is required.

5. The water heater and expansion tank will now be operational. The

expansion tank will control pressure increases caused by thermal

expansion to a level below the water heater relief valve setting.

Maintenance

A licensed professional should check the complete system, including the

expansion tank, yearly and more frequently as the system ages. Checking

the precharge allows a small quantity of air to escape and can result in an

insufficient air charge. Always check the precharge while the tank is isolated

and empty of water, and be sure to maintain the proper precharge whenever

the tank is inspected. Monitor the tip of the indicator cap for discoloration

(Figure 3) in addition to regular product inspection. Contact the installer

or a plumbing professional if indicator cap is discolored; tank replacement

is required. Do not rely on indicator cap as sole means of determining of

tank condition.

Warranty

ST-5 and ST-12 Models: Seven (7) Year Limited Warranty

ST-25V through ST-210V Models: One (1) Year Limited Warranty

T-5 and T-12 Models: One (1) Year Limited Warranty

Visit www.amtrol.com for complete warranty details.

Residential sizing based on: 40°F incoming water temperature; 150 psi T&P safety relief valve; Pre-charge equal to static supply pressure.

Models: ST-5, ST-12, T-5, T-12 for residential use only.

For larger commercial applications: Visit www.amtrol.com, download the AMTROL App or contact Technical Support at 401.535.1216.

Figure 1.

Expansion Tank Volume (Gal.)

Maximum Temperature Setting 180°F

Water Heater

Size

(Gals.)

Static Supply Pressure (psig)

40 60 80

40 ST-12 ST-12 ST-12

50 ST-12 ST-12 ST-12

60 ST-12 ST-12 ST-25V

80 ST-12 ST-25V ST-25V

120 ST-25V ST-25V ST-25V

Expansion Tank Volume (Gal.)

Maximum Temperature Setting 160°F

Water Heater

Size

(Gals.)

Static Supply Pressure (psig)

40 60 80

40 ST-5 ST-5 ST-12

50 ST-5 ST-12 ST-12

60 ST-12 ST-12 ST-12

80 ST-12 ST-12 ST-25V

120 ST-12 ST-25V ST-25V

Expansion Tank Volume (Gal.)

Maximum Temperature Setting 140°F

Water Heater

Size (Gals.)

Static Supply Pressure (psig)

40 60 80

Tankless & POU

up to 2 gal. ST-1 ST-1 ST-1

40 ST-5 ST-5 ST-5

50 ST-5 ST-5 ST-5

60 ST-12 ST-12 ST-12

80 ST-12 ST-12 ST-12

120 ST-12 ST-12 ST-25V

PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY

IMPORTANT GENERAL SAFETY INFORMATION -

ADDITIONAL SPECIFIC SAFETY ALERTS APPEAR IN THE FOLLOWING INSTRUCTIONS.

Figure 3.

Clear / White

Normal

Operation

Discolored

Replace

Tank

InSight® Service Indicator Cap (ST-5 and ST-12 Inline models only)

Figure 2.

In-Line Models Stand Models

Thermal

Expansion

Tank

3/4”

Threaded

Tee

Cold

Water

Supply

Backflow Preventor, Check Valve

or Pressure Reducing Valve

Hot Water

T & P

Relief

Valve

Water

Heater

Turbulator™ Installation (ST-5 and ST-12 only)

Press Turbulator fully

into connector prior

to installing tank.

3/4” Threaded Tee

Turbulator

Tank Connector

Thermal

Expansion

Tank

Hot Water

T & P

Relief

Valve

Water

Heater

Cold

Water

Supply

Backflow Preventor Check Valve

or Pressure Reducing Valve

Remove cap and

charge to cold

supply pressure.

Replace cap

and tighten until

flush with tank.

Precharge Adjustment

One or more features of this product are covered by U.S. patents, visit www.amtrol.com/patents for more information.

1400 Division Road, West Warwick, RI USA 02893

T: 800.426.8765 www.amtrol.com Models up to

10.3 gallons

Produkt Specifikationer

Mærke:	Amtrol
Kategori:	Kedler & kedler
Model:	Therm-X-Trol ST-200V

Har du brug for hjælp?

Hvis du har brug for hjælp til Amtrol Therm-X-Trol ST-200V stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Kedler & kedler Amtrol Manualer

Amtrol Extrol SX-130V Manual

22 August 2024

Amtrol Extrol EX-30 Manual

22 August 2024

Amtrol Extrol Pro EX-15PRO Manual

22 August 2024

Amtrol Extrol SX-40V Manual

22 August 2024

Amtrol Extrol SX-30V Manual

22 August 2024

Amtrol Extrol EX-90 Manual

22 August 2024

Amtrol Therm-X-Trol ST-200V Manual

22 August 2024

Amtrol Therm-X-Trol ST-12 Manual

22 August 2024

Amtrol Extrol SX-110V Manual

22 August 2024

Amtrol Therm-X-Trol ST-60V Manual

22 August 2024

Kedler & kedler Manualer

Nyeste Kedler & kedler Manualer

Daikin EKHWSP180D3V3 Manual

9 April 2025

Daikin SDGTB1209 Manual

9 April 2025

Daikin SDGTB06 Manual

9 April 2025

SIME HOME PLUS Manual

1 April 2025

Corbero CTEV350 Manual

10 Marts 2025

Corbero CTM80 Manual

10 Marts 2025

Stiebel Eltron SHC 15 AU Manual

27 Februar 2025

Stiebel Eltron SNU 5 Plus Manual

27 Februar 2025

Stiebel Eltron DEM 6 Manual

27 Februar 2025

Stiebel Eltron DHCE 8/50 Manual

27 Februar 2025