Antec Rockus 3D 2.1 Manual

Antec Højttaler Rockus 3D 2.1

Læs gratis den danske manual til Antec Rockus 3D 2.1 (1 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 17 anmeldelser. Har du et spørgsmål om Antec Rockus 3D 2.1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

M AX PO W ER

CO NSUM PTIO N:

SUBWOOFER -100W

For additional information and product support, please visit us at .www.soundscienceaudio.com

soundscience™ rockus™ speakers

soundscience™ rockus™ speakers: 1 x subwoofer,

1 x remote control, 2 x satellite speakers

8-pin-to-8-pin RCA-to-open-ended

(red)

RCA-to-open-ended

(white)

3.5 mm-to-3.5 mmRCA-to-3.5 mm

Parts and Components

How to Configure and Connect the soundscience™ rockus™ Speaker System:

1. Carefully remove the two satellite speakers, subwoofer, four sets of cables and remote from the box.

2. Connect the remote to the subwoofer using the supplied 8-pin-to-8 pin cable. Ensure that the pins are correctly

aligned on both ends of the cable before plugging them in.

3. Connect the satellite speakers to the subwoofer using the supplied RCA-to-open-ended speaker cables. Pay

attention to which speakers are left/right and position the speakers accordingly.

4. Connect the subwoofer to your sound source using one of the following methods:

a. RCA-to-3.5 mm cable: Plug the RCA (red & white) end into subwoofer, and plug the other end into your sound

source (i.e. computer, mp3 player, etc.).

b. 3.5mm-to-3.5 mm cable: Plug one end into the subwoofer, and the other end into your sound source (i.e.

computer, mp3 player, etc.).

c. Optical cable (not included): Plug one end into the subwoofer, and the other end into your sound source (i.e.

computer, DVD player, etc.) To enable/disable optical input, press and hold the gray “mode” button on the

front of the remote control for three seconds when the system is powered on.

5. Plug the power cable that is hard-wired into the subwoofer into a power outlet (100-240V, 50-60 Hz).

Note: Although you can use multiple devices for analog input (RCA/3.5 mm), when two devices are connected and playing, both

will be heard simultaneously. However, the volume of either device will be cut in half when both are connecting (even if only

one device is outputting sound).

How to Use the soundscience™ rockus™ Speaker System:

• To turn on the system, flip the power switch on the back of the subwoofer to the “on” position.

• To adjust the strength of the bass, use the switch on the back of the subwoofer labeled “bass level”. By default,

rockus is set to bass level 1 (low).

• To mute the sound, press down on the volume knob on the top of the remote control.

• To switch between “3D” mode and “music” mode, press the gray “mode” button on the front of the remote

control. To enable/disable optical input, press and hold the “mode” button for three seconds.

• To adjust the volume, turn the knob on the top of the remote control.

• The LED lights on the front of the remote indicate the status of the rockus system according to the following scheme:

- Green: optical input active - Blue: music mode enabled

- White: 3D mode enabled - Red: mute

Troubleshooting:

If there is no sound coming from the speakers, check the following:

• Verify the power switch on the back of the subwoofer is in the “on” position, and that the plug is plugged into a

functioning power outlet.

• Make sure your audio source is not muted, and the volume is set to an audible level.

• Make sure both input and speaker cables are firmly connected at both sides.

• Check the status LEDs on the front of the remote to see if the “mute” light is lit. If it is, press down on the top of

the remote to unmute the system.

If you cannot hear a connected optical device:

• Check the status LEDs on the front of the remote control and verify that the optical signal light is lit.

• Verify that optical output is enabled on your audio source.

• Make sure both sides of the audio cable are securely fastened.

On / Off Switch

Bass Level Switch

Subwoofer Back Panel Remote Control

Mute Button

Mode Button

Volume Control

English English

Produkt Specifikationer

Mærke:	Antec
Kategori:	Højttaler
Model:	Rockus 3D 2.1

Har du brug for hjælp?

Hvis du har brug for hjælp til Antec Rockus 3D 2.1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Antec Manualer

Antec SP-0 Manual

26 August 2024

Antec Rockus 3D 2.1 Manual

26 August 2024

Antec SP1 Manual

8 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Energy Sistem TempoRave Manual

11 December 2025

RCF C 5215-W MKIII Manual

10 December 2025

RCF X 28 L Manual

10 December 2025

Fostex PM0.4d Manual

8 December 2025

Amphion Argon 3LX Manual

8 December 2025

Amphion Argon 7LX Manual

8 December 2025

8 December 2025

8 December 2025

7 December 2025

7 December 2025